Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Reliable BARRACUDA 200ZW
Summary of Contents for Reliable BARRACUDA 200ZW
- Page 1 BARRACUDA 200ZW INSTRUCTION MANUAL PORTABLE WALKING FOOT SEWING MACHINE...
- Page 3 THE BARRACUDA 200ZW PORTABLE WALKING FOOT SEWING MACHINE INSTRUCTION MANUAL MATERIAL IS OWNED BY RELIABLE AND MAY NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT EXPRESS WRITTEN PERMISSION FROM RELIABLE CORPORATION COPYRIGHT 2016 RELIABLE CORPORATION...
- Page 4 PREFACE The Reliable Barracuda 200ZW zig-zag and straight stitch portable walking-foot machine is remarkably versatile. Designed for boat owners, hobbyists, and small businesses, the Barracuda is ideal for medium-to-heavy-weight sewing jobs. SMALL SIZE, BIG PERFORMANCE With a stitch quality comparable to an industrial machine, there’s no job too big for the Barracuda.
-
Page 5: Table Of Contents
TABLE OF CONTENTS Machine speed ....................Oiling ....................... Needle ......................Thread ......................Bobbin winding ....................Threading the machine and needle ............Prepare for sewing ..................To start sewing ....................To regulate the length of stitch ..............Reverse sewing ....................Adjusting the tension ................... To remove the hook and clean the race ............ -
Page 6: Machine Speed
SPEED OF MACHINE The maximum speed recommended for this machine is 900 RPM or “stitches per minute”. Use regular house-hold circuit 115 Volts, 60 HZ. The machine is equipped with a one tenth (1/10) HP motor with reduction pulley to provide good power at the recom- mended speed. -
Page 7: Needle
NEEDLE Use 135x17 needles size 10 to 23. Use size 22 for most medium to heavy sewing. Install needle as illustrated. THREAD To obtain the best results with your sewing machine, we recommend size 69 Bonded Nylon Thread. GROOVE... -
Page 8: Bobbin Winding
WINDING THE BOBBIN... -
Page 9: Threading The Machine And Needle
THREADING THE MACHINE AND NEEDLE... -
Page 10: Prepare For Sewing
PREPARE FOR SEWING Thread the machine. Then pick up the bobbin thread as follows: While holding the loose end of the needle thread in your left hand, turn the balance wheel toward you by hand until the needle moves down and up again to its highest point. -
Page 11: To Regulate The Length Of Stitch
TO REGULATE THE LENGTH OF STITCH Most sewing will be done with the maximum stitch length. However, the length of the stitch can be adjusted as follows: Loosen the thumb nut on the stitch length lever. Raise the stitch length (feed regulator) lever until the desired stitch length is obtained. -
Page 12: Adjusting The Tension
ADJUSTING THE NEEDLE THREAD TENSION ADJUSTING THE BOBBIN TENSION... -
Page 13: To Remove The Hook And Clean The Race
TO REMOVE THE HOOK AND CLEAN THE RACE DO NOT FORCE ANY OF THESE OPERATIONS Turn the balance wheel by hand until the needle is at its highest point. Remove the bobbin and bobbin case. Turn knob (A) one half turn toward you. Turn knob (B) one half turn away from you. -
Page 14: Clutch Washer/Screw-Assembly Instructions
CLUTCH WASHER/SCREW-ASSEMBLY INSTRUCTIONS Remove clutch stop screw. Remove hand clutch screw. Notice position of prongs on clutch washer in slot of balance wheel bushing. Remove clutch washer and make 1/2 turn and replace. Screw in hand clutch screw very light Screw in stop screw. -
Page 15: Constructional Drawing
CONSTRUCTIONAL... -
Page 16: External Group
GROUP 1 CONSTRUCTION EXTERNAL GROUP 18-1... -
Page 17: External Group Parts List
GROUP 1 KEY NO. PART NO. PART NAME Q’TY KEY NO. PART NO. PART NAME Q’TY TOP PLATE BOBBIN WINDER SET SCREW W047 B010 B071 TOP PLATE SET SCREW W032 NEEDLE PLATE EO66 BOBBIN WINDER STOPPER A052 NEEDLE PLATE SET SCREW E066-2 BOBBIN WINDER STOPPER SET SCREW A048-B... -
Page 18: Sewing Transmission Group
GROUP 2 SEWING TRANSMISSION GROUP 28-1... -
Page 19: Sewing Transmission Group Parts List
GROUP 2 KEY NO. PART NO. PART NAME Q’TY KEY NO. PART NO. PART NAME Q’TY E053 ARM SHAFT A021 NEEDLE BAR CONNECTING JOINT SET SCREW B007 FEED CAM W015 ZIGZAG CONNECTING ROD B051 ARM SHAFT BUSHING B099 NEEDLE BAR CONNECTING JOINT PIN A012 THREAD TAKE-UP ASSEMBLY SET SCREW WO66... -
Page 20: Shuttle Transmission Group
GROUP 3 SHUTTLE TRANSMISSION GROUP... -
Page 21: Shuttle Transmission Group Parts List
GROUP 3 KEY NO. PART NO. PART NAME Q’TY B139 CRANK CONNECTING ROD A027B CRANK CONNECTING ROD SET SCREW A0278 CRANK CONNECTING ROD SET NUT A023 OSCILLATING SHAFT SET SCREW & NUT A024 OSCILLATING SHAFT A018 SHUTTLE DRIVER PIN OSCILLATING SHAFT CRANK SET PIN A021 OSCILLATING SHAFT CRANK SET SCREW B179... -
Page 22: Feed Transmission Group
GROUP 4 FEED TRANSMISSION GROUP 17-1... -
Page 23: Feed Transmission Group Parts List
GROUP 4 Q’TY KEY NO. PART NO. PART NAME Q’TY KEY NO. PART NO. PART NAME W109 FEED REGULATOR THUMB NUT A07IB-1 FEED ROCK SHAFT CRANK SET SCREW FEED LIFTING ROCK SHAFT CRANK SET SCREW WIO5 FEED REGULATOR LEVER A067 FEED REGULATOR SCREW WASHER A053B-2 FEED REGULATOR LEVER NUT... -
Page 24: Driving & Reversing Mechanism Group
GROUP 5 DRIVING & REVERSING MECHANISM GROUP 17-1... -
Page 25: Driving & Reversing Mechanism Group Parts List
GROUP 5 KEY NO. PART NO. PART NAME Q’TY KEY NO. PART NO. PART NAME Q’TY W042 PRESSER BAR LIFTER C097 BRACKET SET SCREW W042-3 PRESSER BAR LIFTER HINGE SCREW W036 PRESSER BAR FEED ROD W026 LIFT BAR W024-1 PRESSER BAR ACTUATOR SPACER W042-2 UPPER LIFT BAR SCREW W022... -
Page 26: Electric Power & Dynamic Transmission Group
GROUP 6 ELECTRIC POWER & DYNAMIC TRANSMISSION... -
Page 27: Electric Power & Dynamic Transmission Group Parts List
GROUP 6 Q’TY KEY NO. PART NO. PART NAME KEY NO. PART NO. PART NAME Q’TY AOO4 STOP MOTION CLAMP STOP SCREW W049-1 MOTOR BASE SET SCREW AOO2-1 STOP MOTION CLAMP SCREW W049-2 MOTOR SET WASHER A005 STOP MOTION CLAMP WASHER C097 MOTOR SET SCREW A003... -
Page 28: Zigzag Mechanism Group
GROUP 7 ZIG ZAG MECHANISM GROUP... -
Page 29: Zigzag Mechanism Group Parts List
GROUP 7 Q’TY KEY NO. PART NO. PART NAME KEY NO. PART NO. PART NAME Q’TY ZIG ZAG CAM & GEAR (ASSEMBLY) H777 ZIG ZAG CONTROL PLATE SET SCREW (3) FOR NO. 703, 707 412-1 SET SCREW FOR NO. 725(1) 705-2 NEEDLE DISPLACEMENT REGULATOR (ASSEMBLY) SET SCREW FOR NO. -
Page 30: Base Plate & Working Plate
BASE PLATE & WORKING PLATE KEY NO. PART NO. PART NAME Q’TY E316 HEAD SCREW A106 BASE SlDE SET SCREW E428 BASE SIDE PRESSER PLATE W428-1 BASE SIDE PRESSER PLATE RUBBER E425 BASE SHAFT SET SCREW E423 BASE SHAFT E427 BASE PRESSER PLATE E433 BASE PRESSER PLATE RUBBER... -
Page 31: Base Plate & Working Plate Parts List
CUDA CRANK INSTALLATION STOP MOTION SCREW HAND WHEEL 1 Unscrew & remove the stop motion stop screw with screw driver. 2 By hand, unscrew & remove the stop motion screw. 3 Remove clamp washer from under the stop motion screw. 4 Remove the drive belt cover SCREW DRIVER CLAMP WASHER... - Page 32 NEW BELT BIG WHEEL 7 Install the BIG WHEEL on the end of the shaft making sure that the teeth on the wheel are facing the sowing head. 8 Tighten the BIG WHEEL on the 1/8” Allen key provided. 9 Install the new mail drive belt. 1/8"...
-
Page 33: Optional - Cuda Case
OPTIONAL – CUDA CASE • 3/4” plywood construction • Reinforced metal corner guards • Heavy-duty handle • Dual exterior case latches • Separate insert houses the accessory kit for extra needles, bobbins and more... - Page 34 You will be issued a return authorization number (RA#) to new. If Reliable is unable to repair or replace a Barracuda, it will refund the and asked to ship the defective product together with proof of purchase and RA#, current value of that Barracuda at the time the warranty claim is made.
- Page 35 RA#, to new. If Reliable is unable to repair or replace a Reliable Product, it will refund prepaid insured to the following address: Reliable Corporation, 5-100 Wingold Avenue, the current value of that Reliable Product at the time the warranty claim is made.
- Page 40 1 800 268 1649 www.reliablecorporation.com...
Need help?
Do you have a question about the BARRACUDA 200ZW and is the answer not in the manual?
Questions and answers