Panasonic VL-SWD275 Instruction Manual
Hide thumbs
Also See for VL-SWD275:
- Operating instructions manual (41 pages) ,
- Important information and quick manual (16 pages)
Table of Contents
Advertisement
Quick Links
R This guide is for use with the above 2 models.
R Door station is described as "doorphone" and Main monitor station is described as "main
monitor" in this guide.
R In this guide, the suffix of each model number (e.g., the "BX" in "VL-MWD275BX") is omitted
unless necessary.
Note to the installer
R Before attempting to connect or operate this product, please read the nameplate on
the bottom or rear of the product.
R Please read this guide carefully, and install the product safely and correctly by following
the instructions. Carefully read the information found in the section titled "For your
safety" in particular.
R Only use attachments/accessories specified by the manufacturer.
R The installation shall be carried out in accordance with all applicable installation rules.
R
To the maximum extent permitted by law, Panasonic assumes no responsibility for
injuries or property damage resulting from failures arising out of improper installation or
operation inconsistent with this document.
R After installation, make sure to leave this guide with the customer.
Model Name
Wireless Video Intercom System
Main Monitor Station
VL-V524
Door station
Installation Guide
VL-MWD275
Main monitor station
Model No.
VL-SWD275
VL-MWD275
Advertisement
Table of Contents
Related Manuals for Panasonic VL-SWD275
Summary of Contents for Panasonic VL-SWD275
- Page 1 R Only use attachments/accessories specified by the manufacturer. R The installation shall be carried out in accordance with all applicable installation rules. To the maximum extent permitted by law, Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this document.
-
Page 2: For Your Safety
R Do not make any wiring connections For your safety when the power supply is turned on. R Do not use the supplied power supply To prevent severe injury or loss of life or unit for outdoor installations (it is for property, and to ensure proper and safe indoor use only). -
Page 3: Supplied Accessories For Installation
product may cause such devices to R Install the product securely adhering malfunction, resulting in an accident. to the instructions in this guide to prevent it from falling off the wall. Avoid installing onto low-strength CAUTION walls, such as gypsum board, ALC (autoclaved lightweight concrete), Preventing electric shock concrete block, or veneer (less than... -
Page 4: Precautions For Installation
Note: R The illustrations in the supplied manual(s) may vary slightly from the actual product. *1 VL-SWD275 models only *2 VL-SWD275AZ/VL-MWD275AZ models only Precautions for installation To avoid malfunction or communication disturbances, do not install the doorphone or the main monitor/ extension monitor in the following locations: –... - Page 5 Wiring schematic diagram Set up correctly according to the following wiring schematic diagram and "Wire type and length". R For information, such as order numbers, about optional devices that can be connected to, refer to the "Additional/replacement accessories" section in the Operating Instructions. DOORPHONE 1 DOORPHONE 2 MAIN MONITOR...
- Page 6 Wire type and length Wire type Wiring run Diameter Length (Max.) ø 0.65 mm 22 AWG 100 m Doorphone – Main monitor – ø 1.0 mm 18 AWG 130 m Extension monitor ø 0.5 mm CAT 5 50 m ø 0.65 mm 22 AWG 10 m Main monitor –...
- Page 7 n Connecting an optional lobby station For information about connections, refer to the documentation of the lobby station to be connected. Example: VL-V591 Lobby station MAIN MONITOR <Rear view> Ml-1 Ml-2 MO-1 MO-2 MO-3 MO-4 MO-5 MO-6 NP: Non-polarised <Be sure to perform the following to ensure proper operation> R Connecting an optional VL-V591 lobby station –...
-
Page 8: Doorphone Installation Position
Doorphone installation position Installation position of the doorphone and camera range Views when the camera is facing forwards at 0° (default). R Example: Installation height is 1450 mm (standard position). (Units: mm) A view when looking from above A Image range B Approx. 54° C Centre of doorphone D Approx. 1450 E Approx. 500 F Approx. -
Page 9: Installing The Doorphone
When using flush mount box (option): Installing the doorphone Model No. VL-MB524 Install the flush mount box (A) in the Important: wall. R On the bottom surface of the doorphone and the mounting base, there are holes to allow water to drain. - Page 10 Examples of camera angle Attach the doorphone to the mounting base. Facing forwards Facing upwards Facing left Facing upper left A Screws (accessory) ´ 4 When using flush mount box (option): Model No. VL-MB524 Attach the doorphone to the flush mount R The angle can also be adjusted to the right box.
- Page 11 Power supply unit (with cable cover removed) Installing the power supply Top view Bottom view unit (VL-SWD275AZ, VL-MWD275AZ models only) About the installation location R The AC cable plug is used as the main disconnect device. Ensure that the power outlet J DC cable binder hole is installed near the product and is easily accessible.
- Page 12 Attach to the DIN rail Attach in the order described below so that hook Main monitor/extension (A) is positioned at the bottom. monitor installation position Hang hook (B) on the DIN rail (C). Pull and hold the lever down (D). About the installation position of the main monitor/extension monitor and mounting Secure hook (A) to the DIN rail (E).
- Page 13 D Wiring from doorphone or other device Installing the main monitor/ [For power supply unit attached models] extension monitor VL-SWD275AZ/VL-MWD275AZ etc.: Connect the DC cable and wires. Attach the mounting bracket (A) to the wall R Connect the wires correctly according to securely.
- Page 14 2-2 How to make wiring connections [For power supply unit non-attached While pressing on the button (F) with a models] pointed object such as a screwdriver, insert VL-SWD275BX/VL-MWD275BX etc.: the wire into the terminal connector (G). (To 3-1 Line up the tab on the bottom of the disconnect a wire, pull out the wire while bracket with the groove on the main monitor/ pressing on the button (F).)
- Page 15 [For power supply unit attached models] VL-SWD275AZ/VL-MWD275AZ etc.: 3-1 Line up the tab on the bottom of the bracket with the groove on the main monitor/ extension monitor. 3-2 Line up the tab on the top of the bracket with the groove on the main monitor/extension monitor, and push the main monitor/extension monitor down until it is secure.
- Page 16 1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8501, Japan http://www.panasonic.com © Panasonic Corporation 2020 PNQX9067ZA C0320MM0...