Advertisement
Quick Links
SFF time P-ATX v0.1 manual
Dear customer,
Thank you for purchasing SFF time P-ATX case. Please read full compatibility list before assembling your PC. You can find it on sfftime.com.
If you have any doubts about choosing your components, or steps in this manual, please contact us via email on info@sfftime.com, and we will
be glad to assist you.
Important notes:
-
always use the correct screwdriver tip for corresponding bolts (PH1 or PH2)
-
always use the correct bolt type
-
do not overtight the bolts
-
do not force the components in, each component should be installed without using excessive force
1
Advertisement
Related Manuals for SFF time P-ATX
Summary of Contents for SFF time P-ATX
- Page 1 Dear customer, Thank you for purchasing SFF time P-ATX case. Please read full compatibility list before assembling your PC. You can find it on sfftime.com. If you have any doubts about choosing your components, or steps in this manual, please contact us via email on info@sfftime.com, and we will be glad to assist you.
- Page 2 SFF time P-ATX v0.1 manual 1. Installing the motherboard (ATX, m-ITX, e-ATX, m-DTX) prepare the motherboard by installing cpu, ram, m.2 drives, and cpu air cooler if using one install the IO shield align the motherboard on the standoffs screw the motherboard down using provided bolts after installing the motherboard, connect internal USB 3.0 cable, and power switch and power LED...
- Page 3 SFF time P-ATX v0.1 manual 2. Installing the motherboard (m-ATX) follow the instructions from step no.1, and in addition install two extra standoffs as shown on the picture...
- Page 4 SFF time P-ATX v0.1 manual 3. Installing the GPU riser cable (2 slot GPU) carefully bend the riser cable in a way shown on the picture (it has to go under the riser PCB) screw the riser to the two standoffs in the...
- Page 5 SFF time P-ATX v0.1 manual 4. Installing the GPU riser cable (2.1-3 slot GPU) graphic cards thicker than 2 slot can only be installed if using m-ITX motherboard follow the instructions from step no.3, and in addition install two extra standoffs...
- Page 6 SFF time P-ATX v0.1 manual 5. Installing the GPU – part 1 plug the graphic card into the riser engage the latch at the end of the riser connector screw the graphic card to the case using two provided bolts...
- Page 7 SFF time P-ATX v0.1 manual 6. Installing the GPU – part 2 carefully plug the male end of the GPU riser cable in the PCI-E x16 slot on the motherboard...
- Page 8 SFF time P-ATX v0.1 manual 7. Installing the SFX power supply – part 1 put the power supply on the flat surface, with fan side up take the power supply mounting bracket and put in next to power supply like...
- Page 9 SFF time P-ATX v0.1 manual 8. Installing the SFX power supply – part 2 before Installing the power supply to the case, insert the AC plug to the connector on the power supply like shown on the picture power supply fan should be...
- Page 10 SFF time P-ATX v0.1 manual 9. Installing the SFX power supply – part 3 screw the power supply bracket to the case from the back side using two provided screws...
- Page 11 SFF time P-ATX v0.1 manual 10. Installing hard drives – part 1 prepare your hard drives by screwing in the provided bolts to the right side of the drive like shown on the picture if you are using both 2.5 and 3.5 inch drives, then you only need to apply this step to the 3.5 inch drive...
- Page 12 SFF time P-ATX v0.1 manual 11. Installing hard drives – part 2 screw down the hard drives to the mounting bracket with provided bolts be careful, 2.5 and 3.5 inch drives use different type of bolts...
- Page 13 SFF time P-ATX v0.1 manual 12. Installing hard drives – part 3 line up the hard drives so that the bolt heads on the right side of the hard drives slide into the holes on the front of the case...
- Page 14 SFF time P-ATX v0.1 manual 13. Installing hard drives – part 4 if using radiator or long graphic card, you might want to install 2.5 inch hard drive to the alternative location above the motherboard, on the back side of the case...
- Page 15 SFF time P-ATX v0.1 manual 14. Installing case fans optionally, you can install up to three 60mm case fans on the top of the case place the fans above the motherboard like shown on the picture, and screw them to the...
- Page 16 SFF time P-ATX v0.1 manual 15. Installing the water cooling radiator optionally, you can install 120 mm water cooling radiator in the position normally occupied by hard drives place the radiator in a position shown on the picture, and screw it to the case using four...
- Page 17 SFF time P-ATX v0.1 manual 16. Closing the left side panel – part 1 lay the case on its right side place the left panel on the cases side flanges slide the panel into the channels on the case, making sure that both front and top part of the...
- Page 18 SFF time P-ATX v0.1 manual 17. Closing the left side panel – part 2 screw the left panel to the case using provided thumb screw like shown on the picture...
- Page 19 SFF time P-ATX v0.1 manual 18. Closing the right side panel – part 1 lay the case on its left side place the right panel on the case slide the panel into the channels on the case, making sure that both front and top...
- Page 20 SFF time P-ATX v0.1 manual 19. Closing the right side panel – part 2 screw the right panel to the case using provided screw like shown on the picture IMPORTANT NOTE: use only 3 mm bolt for securing the right side panel, using longer...
- Page 21 SFF time P-ATX v0.1 manual 20. Attaching the stand put the case on the stand so that the tabs on the stand enter the slots at the bottom of the case, like shown on the picture...
- Page 22 SFF time P-ATX v0.1 manual 20. Build complete congratulations, you have completed your build in the P-ATX case! if you have any questions, comments or want to send us your feedback, please write to us at info@sfftime.com be sure to check out our website sfftime.com to see the...
Need help?
Do you have a question about the P-ATX and is the answer not in the manual?
Questions and answers