Sealey ML11.V2 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: please read THese insTrUCTiOns CareFUlly. nOTe THe saFe OperaTiOnal reQUiremenTs, warnings & CaUTiOns.
Use THe prOdUCT COrreCTly and wiTH Care FOr THe pUrpOse FOr wHiCH iT is inTended. FailUre TO dO sO may CaUse
damage and/Or persOnal inJUry and will invalidaTe THe warranTy. please Keep insTrUCTiOns saFe FOr FUTUre Use.
1. saFeTy insTrUCTiOns
1.1. eleCTriCal saFeTy
warning! it is the user's responsibility to read, understand and comply with the following:

You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and
all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An rccB (residual current circuit Breaker) should be incorporated in the main distribution board. We also recommend that an rcd
(residual current device) is used with all electrical products. It is particularly important to use an rcd with portable products that are plugged
into an electrical supply not protected by an rccB. If in doubt consult a qualified electrician. You may obtain a residual current device by
contacting your sealey dealer. you must also read and understand the following instructions concerning electrical safety.
1.1.1. the electricity at work act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the Health & safety at work act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. ensure the insulation on all cables and the product itself is safe before connecting to the mains
power supply. see 1.1.1. & 1.1.2. above and use a Portable Appliance tester (PAt).
1.1.4. ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply, leads, plugs for wear and damage and all electrical connections to
ensure that none is loose.
1.1.6. Important: ensure that the product voltage matches the power supply to be used.
1.1.7. dO nOT pull power plugs from sockets by the power cable.
1.1.8. dO nOT use worn or damaged leads, plugs or connections. Immediately replace or have repaired by
a qualified electrician. A u.K. 3 pin plug with AstA/Bs approval is fitted.
In case of damage, remove and fit a new plug according to the following instructions (discard old
plug safely). (uK only - see diagram at right).
Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the green/yellow earth wire to the earth terminal 'E'.
b) Connect the brown live wire to live terminal 'L'.
c) Connect the blue neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that cable outer insulation extends beyond the cable restraint and that the restraint is tight.
2. inTrOdUCTiOn
High output lighting with even spread of light. low power consumption on both led and fluorescent models saving on energy costs.
Manufactured to low Voltage directive 73/23/eec. each model is supplied with 5mtr cable and Bs approved plug. Ideal for the professional
garage/workshop user.
3. TeCHniCal speCiFiCaTiOns
model no: ............................................. ml11.v2
voltage: ................................................. 230v
power:................................................... 11w
lamp Type: ........................................... neon Tube
Tube included: ..................................... yes
Cable length: ....................................... 5mtr
Fitted plug: ........................................... yes
Overall length: .................................... 420mm
reolacement Tube: .............................. ml11/12/B
4. OperaTiOn
4.1. to use the lamp, plug it into a mains socket to turn the light on.
4.2. When finished, disconnect the plug from the mains supply, and store it in a safe, dry and childproof location.
© Jack sealey limited
InstructIons for:
energy saving lead lamp
11w/230v
Model no: ml11.v2
Original Language Version
reCOmmended
FUse raTing: 3amp
Ml11.V2 Issue no.1 30/09/13