Table of Contents
Advertisement
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL
To avoid damaging the treadmill, adjust the incline
to zero before you fold the treadmill. Then, remove
the key and unplug the power cord. CAUTION: You
must be able to safely lift 45 lbs. (20 kg) to raise,
lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown
by the arrow below. CAUTION: Do not hold the
frame by the plastic foot rails. Bend your legs
and keep your back straight.
1
Frame
2. Hold the frame firmly with your right hand. Pull the
latch knob to the left and hold it. Raise the frame
until the latch plate is past the latch pin. Then,
slowly release the latch knob; make sure that the
latch plate is resting against the latch pin.
2
Latch
Knob
To protect the floor or carpet, place a mat under the
treadmill. Keep the treadmill out of direct sunlight. Do
not leave the treadmill in the storage position in tem-
peratures above 85°F (30°C).
Engaged
Latch
Knob
Latch Pin
Latch Plate
HOW TO MOVE THE TREADMILL
Before moving the treadmill, fold it as described at
the left. CAUTION: Make sure that the latch plate is
resting against the latch pin. Moving the treadmill
may require two people.
1. Hold the frame and one of the handrails, and place
one foot against a wheel.
1
Handrail
Wheel
2. Pull back on the handrail until the treadmill will roll
on the wheels, and carefully move it to the desired
location. CAUTION: Do not move the tread-
mill without tipping it back, do not pull on the
frame, and do not move the treadmill over an
uneven surface.
3. Place one foot against a wheel, and carefully lower
the treadmill.
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2. Hold the upper end of the treadmill
with your right hand. Pull the latch knob to the left
and hold it. Next, lower the frame until it is past
the latch pin. Make sure that the pin does not hit
against the foot rail. Then, release the latch knob.
2. See drawing 1 at the left. Hold the metal frame
firmly with both hands, and lower it to the floor.
CAUTION: Do not hold the frame by the plastic
foot rails, and do not drop the frame. Bend your
legs and keep your back straight.
22
Frame
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the H70t and is the answer not in the manual?
Questions and answers
Doit on lubrifier le tapis roulant et si oui à quels endroits?
Yes, the HealthRider H70T treadmill should be lubricated. The treadmill belt is specified as a "2 Ply Lubricated Treadmill Belt," indicating that lubrication is necessary for its proper functioning. The lubrication should be applied between the treadmill belt and the deck to reduce friction and ensure smooth operation. Follow the manufacturer's instructions in the manual for the correct application process and frequency.
This answer is automatically generated
what size of hex key is for the treadmill?
The included hex key is used to adjust the walking belt on the HealthRider H70T treadmill. However, the specific size of the hex key is not mentioned in the provided context.
This answer is automatically generated
H70t turns on then shuts off. I need some help
The Healthrider H70t treadmill turns on, but the motor does not run. The user reports that the LCD screen comes on, the console safety key is inserted, and the incline motor fan is turning. This suggests that power is reaching the treadmill, but the main motor may not be functioning due to a faulty motor, a damaged motor controller, or a wiring issue. Further troubleshooting is needed to check for error codes, loose connections, or a failed motor control board.
This answer is automatically generated
When i step on it the treadmill stops help
The HealthRider H70T treadmill may stop when you step on it due to insufficient lubrication on the walking belt. The manual advises against applying silicone spray or other substances unless instructed by an authorized service representative. If the walking belt still slows when walked on, refer to the front cover of the manual for further instructions.
This answer is automatically generated