Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Datalogic DX8200A-3002
Summary of Contents for Datalogic DX8200A-3002
- Page 1 DX8200A-3002 QUICK REFERENCE GUIDE 821001253 (Rev. C)
-
Page 2: Updates And Language Availability
- Material Return Authorization LEGAL NOTICES © 2005 - 2010 Datalogic Automation S.r.l. ALL RIGHTS RESERVED. Protected to the fullest extent under U.S. and international laws. Copying, or altering of this document is prohibited without express written consent from Datalogic Automation S.r.l. - Page 3 DX8200A-3002 QUICK GUIDE DX8200A-3002 GENERAL VIEW Figure A Laser Beam Output Windows Laser Safety Label Mounting Slots Mounting Reference Label Figure B Programming Keypad TX Data LED (Green) Power On LED (Green) Network LED (Red) LCD Display Phase On LED (Yellow)
- Page 4 DX8200A-3002 QUICK GUIDE CONNECTIVITY Local Lonworks Network Host ETHERNET CAB-SC6103 Cable VAC INPUT SC6000 Power/Net CAB-SC6013 CAB-SC6003 Extended I/O LONWORKS ENCODER BTK-8500 CAB-85xx Bus Return PS Aux CAB-85xx CAB-85xx CAB-85xx CAB-85xx BTK-8500 Bus Return DX8200A-3002 DS8100A-3002 DX8200A-3002 DS8100A-3002 CAB-85xx CAB-85xx...
- Page 5 DX8200A-3002 QUICK GUIDE to Host ETHERNET SC6000 VAC INPUT CAB-SC6103 Power/Net CAB-SC6013 Working CAB-SC6003 Controller Extended I/O LONWORKS ENCODER CAB-85xx PS Aux CAB-85xx CAB-85xx CAB-85xx BTK-8500 DX8200A-3002 DS8100A-3002 DX8200A-3002 DS8100A-3002 Redundancy CAB-PWO 03 to Host ETHERNET VAC INPUT SC6000 Power/Net...
-
Page 6: Electrical Connections
DX8200A-3002 QUICK GUIDE SC6000 Working Conveyor SC6000 Protecting Example Redundant Reading Station ELECTRICAL CONNECTIONS Two 17-pin connectors provide access to the scanner’s local Lonworks network used for both input and output connections to build a multi-sided or omni-station system. 17-pin Lonworks Connector Pinout... -
Page 7: Technical Features
DX8200A-3002 QUICK GUIDE APPENDIX TECHNICAL FEATURES ELECTRICAL FEATURES Supply Voltage 20 to 30 Vdc Power Consumption 1.5 to 1.0 A; 30 W typical 1.75 to 1.17 A; 35 W Max. (including startup current) Auxiliary Baud Rate Communication Interfaces RS232 1200 to 115200... - Page 8 DX8200A-3002 QUICK GUIDE ENVIRONMENTAL FEATURES Operating Temperature 0° to +50 °C (+32° to +122 °F) Storage Temperature -20° to +70 °C (-4° to +158 °F) Humidity 90% non condensing Ambient Light Immunity 20000 lux Vibration Resistance EN 60068-2-6 Frequency range from 5 to 150 Hz;...
-
Page 9: Mechanical Installation
MECHANICAL INSTALLATION DX8200A-3002 can be installed to operate in any position. There are 4 slots (dia. 8.5 mm) on the sides of the scanner for mounting. The diagram below can be used for installation; refer to the Reading Diagrams for correct positioning of the scanner with respect to the reading zone and scanner orientation. -
Page 10: Scanner Direction
DX8200A-3002 Scanner Direction 0° (Forward) DX8200A-3002 Scanner Direction 180° (Reverse) READING DIAGRAMS Note: x = 0 and z = 0 correspond to the edge of the DX8200A-3002 scanner as shown in the figure below. DX8200A-3002 (0.50 mm/20 mils) (in) -100... -
Page 11: Laser Safety
DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT MAXIMUM OUTPUT RADIATION 1 mW EMITTED WAVELENGTH 630~680 nm TO EN 60825-1:2001 Datalogic Automation S.r.l. Via Candini, 2 40012 Calderara di Reno - Bologna - Italy Manufactured Volt Model No. Amp. -
Page 12: Fcc Compliance
DX8200A-3002 QUICK GUIDE FCC COMPLIANCE Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment. This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference which may cause undesired operation.
Need help?
Do you have a question about the DX8200A-3002 and is the answer not in the manual?
Questions and answers