Philips AutoDome TC700 Series User Manual page 7

Camera - Using Auxiliary Controls
Camera Aux
Function No.
BL_COMP 20
HIGH-LIGHT 21
SHUTTER_ADJ 22
SHUTTER 23
WHITE_BALANCE 30
RED 31
BLUE 32
R_Y_HUE 33
B_Y_HUE 34
FIXED_WB 35
FACTORY_ 40
DEFAULTS
LL_PHASE 41
SYNC 42
AGC 43
Note: Auto-pan is discontinued when the manual pan
control (joystick) is used.
Auto-iris and auto-focus revert to manual mode when the
manual iris and focus controls are used, respectively.
Switching to manual iris or manual focus from auto mode
reverts to the last manual setting used.
Auto-focus is activated automatically upon pan or tilt
when Auto-focus Activation is on (AUX #12).
Manual iris is activated automatically upon activating
(ON) Backlight Compensation.
Commands Using Pre-Position Controls
Receiver/Driver Pre-
Function Position
No.
Pre-position 1-60
Future 61-100
PP Expansion
Auto-pan 101
left limit
Auto-pan 102
right limit
Home Position 110
Disable/Enable 901-960
PP
Global Disable/ 900
Enable PP
Description On/Off
Backlight On/off
Compensation
Highlight On/off
Shutter Adjust Inc/dec
Shutter On/off
White Balance Auto/
manual
Red Adjust Inc/dec
Blue Adjust Inc/dec
R-Y Hue Adjust Inc/dec
B-Y Hue Adjust Inc/dec
Fixed Indoor/out
White Balance door
Factory Default Set/---
Settings
Adjust LL Phase Inc/dec
Delay
Sync Mode ll/xtal
AGC On/off
Description SET/SHOT
--- Set/show
--- ----/----
--- Set/show
--- Set/show
--- Recalibrate/
show
--- Disable/
enable
--- Disable/
enable
Notes:
1. The following settings are stored with pre-position
Notes
scenes:
Pan position.
1
Tilt position.
Zoom position.
1, 7
Focus mode AUTO/MANUAL.
1
Focus position for MANUAL mode.
1
Iris mode AUTO/MANUAL.
8
Iris ALC/LEVEL for AUTO mode or position for
MANUAL mode.
1, 8
White Balance mode AUTO/MANUAL (color
1, 8 cameras only).
Red content and Blue content for MANUAL
3, 8
mode (color cameras only).
3, 8
Shutter mode ON/OFF.
1, 8
Shutter setting for ON mode.
Backlight compensation ON/OFF.
1,3
Highlight ON/OFF (monochrome cameras only).
3
2. The following settings are stored as a default setting
in nonvolatile memory (EEPROM) on R/D board and
3
are used to restore settings at power-up:
3
Auto-pan left limit = 0 degrees.
Auto-pan right limit = 359.9 degrees.
Auto-pan speed = 30 degrees per second.
Auto-focus activation = ON.
Auto-iris activation = ON.
Auto-speed = OFF.
3. This setting stored as a default setting in nonvolatile
memory in camera.
4. Pre-position #1 (if set) is automatically called-up
upon power-up just after the homing sequence.
5. Scan direction determined by last manual pan
direction.
6. Pre-positions can be disabled such that they do not
operate during pre-position tour. They are still
Notes
available for manual call-up.
7. Applies to monochrome cameras only.
4
8. Applies to color cameras only.
--
Auto-Playback
2
Applicable only to units fitted with this feature.
2
Recording Playback:
1. Position AutoDome to the point where playback is to
--
start.
6
2. Press On, AUX 100, ENTER.
3. Begin controlling the AutoDome.
6
4. At the completion of controlling the AutoDome, press
Off, AUX 100, ENTER.
Note: If you run out of record time prior to issuing the stop record
command, the AutoDome will position itself at the beginning and
not move until the joystick is released for one second.
7