Wash Cycles - Electrolux ELAI3 Series User Manual

• Cycle II (recommended)
For very dirty dishes: press button Wash cycle 2 (see table
of times).
• Cycle III
For very dirty dishes: press button Wash cycle 3 (see table
of times).
• To stop the wash cycle, just press the selected cycle button
or open the door.
• To continue the wash cycle, press the cycle button again or
close the door. The cycle starts again from where it was
stopped.
• At the end of the wash, the dishwasher emits a series of
beeps and the message "END" blinks on the display:
IMPORTANT
At the end of the rinse phase for wash cycle 2
(VUCA060 model) or cycle 3 (EUCA060,
EUCA060/DD,
models), the dishwasher carries out a pause
stage of 1 minute. Plus the door lock hinders
door open to avoid interruption of the wash cycle
by opening the door. This procedure complies
with requirement to meet "A060" level according
to EN 15883-1 Standard, also improving the
drying result on the wares.
• Open the door and remove the rack containing the clean
dishes.
CAUTION
The use of "foaming/nonspecific" deter-
gents or in any case detergents used in
different ways from that prescribed by the
manufacturer, can cause damage to the
dishwasher and compromise the washing
results.
NOTE!
To obtain excellence washing performance, use
detergent, rinse aid and descaling agent sug-
gested by Electrolux Professional. In the Electrolux
Professional web site, open the "Accessories and
Consumables" web page and navigate into the
dishwashing equipment tab to order most suitable
detergents and accessories.
J.5

Wash cycles

The wash cycle includes one wash with hot water and
detergent (min 55℃ [131℉]) and one rinse with hot water and
rinse-aid (min 82 ℃ [180℉]).
20
EUCA060WS and ZUCA60
NOTE!
• The "Thermal Label" model is designed to
guarantee thermal sanitization with a temper-
ature of 71℃ [160℉] reached at tableware
surface when operating continuously, loaded at
70% of nominal productivity (i.e. racks slightly
spaced). Since the performance depends on the
load and environmental and water feed condi-
tion, before starting washing operations it is
suggested to test (using 71℃ [160℉] thermal
labels) a full-load rack to confirm the effective-
ness of parameters; in case of test failure, a
lower speed washing cycle must be set and the
test repeated.
• In the "Hygiene & Clean" model, the wash cycle
includes a wash with hot water and detergent at
a temperature of at least 77℃ [170℉] and a
rinse with hot water and rinse aid (min. 90℃
[194℉]).
Table of times: standard cycle time with supply water at
50℃ [122℉]
Model
ELAI1G - CLAI1G -
ELAI1GCL - ELAI1WG
- NLAI1WG - ELAI1G8
- ELAI1G4 -
ELI1G36M
ELAI3... - ZLAI3... -
NLAI3... - VLAI3... -
XLAI3... - ELI3 - ZLI3 -
ELI3CG - ZLI3CD -
ELAI3WP - ZLAI3WP -
ZLAI3WG - ELI3G5M -
ELI3G35M - ELI3G6M
- DW6-38
ELAI3GTL -
ELAI3GCL
VLAI1G8 - VLAI1G4
VLAI3G
ELAI3GUSPH5 -
ELAI3GUSPH6
ELAI3GWL
EUCA060 - ZUCA060
ELAI3PML -
ELAI3WGML
VUCA060
1. Wash cycle compliant with A060 standard is guaranteed using supplied
racks.
2. Compliant with DIN10512 Standard.
3. Disinfection cycle. Compliant with A060 level according to EN 15883-1
Standard.
Table of times: standard cycle time with supply water at
10℃ [50℉]
Model
ET5AI - ET5AIP
NOTE!
Standard cycle time may vary should the inlet
water temperature and/or the boiler heating ele-
ments be different from that indicated above.
A device lengthens the cycle time if the water in the boiler has
not reached the minimum temperature for correct rinsing.
The cycle times and the temperature may be personalised (e.g.
increase of the rinse time and temperature). The cycle times
should only be set by a specialised personnel.
90 sec 120 sec 240
120 sec 240 sec
90 sec 180 sec
120 sec 180 sec 240 sec
90 sec 113 sec 173 sec
2 2
90 sec 120 sec 240 sec
2 3
90 sec 240 sec
90 sec 120 sec 120 sec
1
-
-
3
-