Page 1 R E V ® G E N 4 T R A I L / C R O S S O V E R A C E S E R I E S OP E R AT OR ’S GUIDE WARNING Read this guide thoroughly.
Page 2 WARNING Disregarding any of the safety precautions and instructions SAFETY VIDEO contained in this Operator's Guide, on-product safety labels could cause injury including the pos- sibility of death! WARNING This vehicle may exceed the performance of other vehicles you may have ridden. Take time to familiarize yourself with your new vehicle.
Page 3: Foreword
FOREWORD The following are trademarks of Bombardier Recreational Products Inc. or its subsidiaries. Renegade™ Ski-Doo ® ACE™ HPG™ Adrenaline™ iTC™ RER™ XPS™ pDrive™ D.E.S.S.™ ® X-RS™ Enduro™ Pilot™ rMotion™ Quick G4™ ROTAX™ Adjust™ The KYB Pro series is a registered mark of KYB America LLC.
Page 4 Whatever model you have chosen, it is backed by the Bombardier Recreational Products Inc. (BRP) warranty and a network of autho- rized Ski-Doo snowmobile dealers ready to provide the parts, service or accessories you may require. Your dealer is committed to your satisfaction. He has taken training...
Page 5: Know Before You Go
FOREWORD Know Before you Go To learn how to reduce the risk for you, your passenger or bystanders being injured or killed, read the following sections before you operate the vehicle: SAFETY INFORMATION – VEHICLE INFORMATION – The proper functioning of a snowmobile depends in part on the sur- face on which it is driven.
Page 6: Refer To Other Sources Of Information
Safety Card on the vehicle, all on-product safety labels and watch SAFETY VIDEO located at: https://www.ski-doo.com/safety Or, use the following QR code. We highly recommend that you take a safety riding course. Please check with your dealer or local authorities for availability in your area.
Page 7: Table Of Contents
TABLE OF CONTENTS FOREWORD ............1 Know Before you Go .
Page 8 TABLE OF CONTENTS IMPORTANT ON-PRODUCT LABELS (cont’d) Vehicle Safety Labels ......... . 53 Compliance Labels .
Page 9 TABLE OF CONTENTS LARGE PANORAMIC 7.8" WIDE LCD DISPLAY ....Basic Functions ..........Settings.
Page 10 TABLE OF CONTENTS VEHICLE TRANSPORTATION ........MAINTENANCE MAINTENANCE SCHEDULE .
Page 11 ® BRP LIMITED WARRANTY USA AND CANADA: 2021 SKI-DOO SNOWMOBILES ..........
Page 12 TABLE OF CONTENTS __________________...
Page 13: Safety Information
SAFETY INFORMATION ____ SAFETY INFORMATION...
Page 14: General Precautions
GENERAL PRECAUTIONS Avoid Carbon Monoxide Poisoning All engine exhaust contains carbon monoxide, a deadly gas. Breath- ing carbon monoxide can cause headaches, dizziness, drowsiness, nausea, confusion and eventually death. Carbon monoxide is a colorless, odorless, tasteless gas that may be present even if you do not see or smell any engine exhaust.
Page 15: Avoid Burns From Hot Parts
WARNING Never carry a passenger on a seat not approved by BRP. WARNING Passenger seat must have a strap or handholds and must meet SSCC standards. See your authorized Ski-Doo dealer for available accessories for your vehicle. ____ SAFETY INFORMATION...
Page 16: Special Safety Messages
SAFETY the snowmobile, the Operator's Guide and watch the VIDEO at www.ski-doo.com/safety before operating the snow- mobile. Only allow a new operator to operate the snowmobile in a restricted flat area, at least until he is completely familiar with its operation. If snowmobile operator's training course is offered in your area, have him enroll.
Page 17 SPECIAL SAFETY MESSAGES – Injury or death may result to the snowmobile operator, passenger or bystander if the snowmobile is used in risky conditions which are beyond the operator's, passenger's or snowmobile's capabil- ities or intended use. – BRP recommends the operator has at least 16 years old of age. Verify also your local laws for age and training requirements.
Page 18 SPECIAL SAFETY MESSAGES – Avoid road traveling. If you must do so, and it is permitted, re- duce speed. The snowmobile is not designed to operate or turn on paving. When crossing a road, make a full stop, then look carefully in both directions before crossing at a 90°...
Page 19 – Do not stud the track unless it has been approved for studs. At speed, a studded track that has not been approved for studs could tear and separate from vehicle. See an authorized Ski-Doo dealer for current specific studding availability and applications.
Page 20 SPECIAL SAFETY MESSAGES – You may stud the track on this vehicle model. However, you MUST only use the BRP approved type stud for use on Ski-Doo snowmobiles. DO NOT EVER use conventional studs because the track thickness is thinner then our standard tracks. The stud could tear off of track and separate from vehicle.
Page 21: Active Technologies (Itc)
ACTIVE TECHNOLOGIES (iTC) Introduction NOTE: Some functions or features described in this section may not apply to every model, or may be available as an option. The throttle is electronic and provides a command signal to an elec- tronic module whose function is to assure proper operation of its sys- tem within set parameters.
Page 22: Riding The Vehicle
Ski-Doo dealer is a great opportunity for your dealer to verify if your snowmobile is included in any safety campaign. We also urge you to visit your authorized Ski-Doo dealer in a timely manner if you become aware of any safety related campaigns.
Page 23 4. Check fuel and oil levels and look for leaks. Replenish if neces- sary and in case of any leaks; you should seek service from an authorized Ski-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement. Please refer...
Page 24 RIDING THE VEHICLE Pre-Ride Check List ✔ ITEM OPERATION Body including seat, footrests, Check condition and remove snow or lights, air filter, ice. controls and instruments Skis and steering Check for free movement and proper ACTION operation. Fuel and oil Check for proper level and no leaks.
Page 25: How To Ride
RIDING THE VEHICLE ✔ ITEM OPERATION Slider shoes Check for proper operation. Check for cracks, fraying or abnormal Drive belt wear and proper height. Horn (if equipped) Check for proper operation. How to Ride Riding Gear Proper snowmobile clothing should be worn. It should be comfort- able and not too tight.
Page 26 RIDING THE VEHICLE What to Bring First aid kit Provided tool kit Mobile phone Knife Flashlight Spare spark plugs Friction tape Trail map Spare drive belt Snack Rider Position (Forward Operation) Your riding position and balance are the two basic principles of making your snowmobile go where you want it to.
Page 27 RIDING THE VEHICLE mmo2008-003-001 Posting A semi-sitting position with the body off the seat and the feet under the body in a sort of squatting posture, thus allowing the legs to absorb the shocks when traveling over uneven terrain. Avoid abrupt stops.
Page 28 RIDING THE VEHICLE Kneeling This position is achieved by placing one foot firmly on the running board and the opposite knee on the seat. Avoid abrupt stops. mmo2008-003-003 Standing Place both feet on the running boards. Knees should be flexed to absorb the shock from surface bumps.
Page 29: Carrying A Passenger
RIDING THE VEHICLE mmo2008-003-004 Rider Position (Reverse Operation) We recommend sitting on your snowmobile when operating in reverse. Avoid standing up. Your weight could shift forward against throttle lever while operating in reverse, causing an unexpected acceleration. WARNING Unexpected acceleration when snowmobile operates in re- verse can cause a loss of control.
Page 30 RIDING THE VEHICLE WARNING Any passenger must be able to firmly lay his feet on the footrests and keep his hands on the handholds or seat strap at all times when seated. Respecting those physical criteria is important to ensure that the passenger is stable and to reduce the risks of ejection.
Page 31: Terrain/Riding Variations
RIDING THE VEHICLE WARNING When riding with a passenger: – Braking ability and steering control are reduced. Decrease speed and allow extra space to maneuver. – Adjust suspension according to weight. For complete information on how to adjust the suspension, please TUNE YOUR RIDE refer to Riding with a Child...
Page 32 RIDING THE VEHICLE Deep Snow In deep “powder” snow, your vehicle could begin to “bog” down. If this occurs, turn in as wide an arc as possible and look for a firmer base. If you do get “bogged”, and it happens to everyone, do not spin your track as this makes the vehicle sink deeper.
Page 33 RIDING THE VEHICLE position. Keep your weight on the uphill side at all times. Maintain a steady, safe speed. Continue as far as you can in this direction, then switch to an opposite hill angle and riding position. A direct climb could present problems. Choose the standing posi- tion, accelerate before you start the climb and then reduce throttle pressure to prevent track slippage.
Page 34 RIDING THE VEHICLE aware of the conditions and dangers on a daily basis when in the mountains. Check local avalanche forecasts and threats each day before heading out to ride and heed forecasters advice. You should always carry a snow shovel, probe and avalanche bea- con while riding on mountains.
Page 35 RIDING THE VEHICLE Bright Sunshine Bright sunny days can considerably reduce your vision. The glare from sun and snow may blind you to the extent that you cannot easily distinguish ravines, ditches or other obstacles. Goggles with colored lenses should always be worn under these conditions. Unseen Obstruction There may be obstructions hidden beneath the snow.
Page 36 RIDING THE VEHICLE “banking” condition beneath the track. By adopting this position and positioning yourself as far forward as possible, weight will be transferred to the inside ski. On occasion, you will find that the only way to turn the vehicle about in deep snow is to pull the snowmobile around.
Page 37 RIDING THE VEHICLE Railroad Crossing Never ride on railroad tracks. It is illegal. Railroad tracks and railroad rights-of-way are private property. A snowmobile is no match for a train. Before crossing a railroad track, stop, look and listen. Night Rides The amount of natural and artificial light at a given time can effect your ability to see or to be seen.
Page 38: Environment
RIDING THE VEHICLE Trail Stops Whenever possible, pull off the trail when you stop. This will reduce the hazard to other snowmobilers using the trail. Trails and Signs Trail signs are used to control, direct or regulate the use of snowmo- biles on trails.
Page 39 RIDING THE VEHICLE It is in every one's best interest to tread lightly into our recreational ar- eas. Because, in the long run, to protect the sport we must preserve the environment. Recognizing the importance of this issue and the need for snowmo- bilers to do their share in preserving areas that make it possible to en- joy our sport, BRP has developed the “Light Treading Is Smart Sled- ding”...
Page 40 Finally, Light Treading is the sign of a smart snowmobiler. You don't have to leave big tracks or careen through a virgin forest to show you can ride. So whether you're driving a high performance Ski-Doo, a sporty snowmobile or any other make or model, show you know what you're doing.
Page 41: Traction Enhancing Products
The stud could tear off of track and separate from vehicle. See an authorized Ski-Doo dealer for current specific studding availability and applications. Using traction enhancing products such as, adjustable or more...
Page 42 TRACTION ENHANCING PRODUCTS ski runners are adequate, they don’t necessarily give you optimal control, since that depends on your personal preferences, your riding style, and how your suspension is adjusted. WARNING If the front and rear of the snowmobile are out of balance due to an incorrect combination of traction enhancing products, the snowmobile may tend to oversteer or understeer, which could lead to a loss of control.
Page 43 TRACTION ENHANCING PRODUCTS A33A33A UNDERSTEERING Controlled Driving A balanced combination of carbide ski runners and studs on the track ensures adequate control and better handling, see illustration. A33A34A CONTROLLED DRIVING ____ SAFETY INFORMATION...
Page 44: Acceleration
TRACTION ENHANCING PRODUCTS Acceleration Using studs on the track will allow your sled to accelerate better on packed snow and ice but will have no noticeable effect on soft snow. This can cause sudden variations in traction under certain conditions. WARNING To prevent surprises that could lead to a loss of control of the snowmobile:...
Page 45: Effects Of Having A Studded Track On The Life Of The Snowmobile
TRACTION ENHANCING PRODUCTS Effects of Having a Studded Track on the Life of the Snowmobile The use of traction enhancing products can increase the load and the stress on certain snowmobile components, as well as the vibra- tion level. This can cause premature wear on parts such as belts, brake linings, bearings, chain, chaincase sprocket, and on approved studded tracks, shorten track life.
Page 46 TRACTION ENHANCING PRODUCTS A00A8KA TRACK SYMBOLS 1. Approved 2. NOT Approved To ensure safe and proper installation, BRP recommends to have the studs installed by your dealer. – Use only the BRP approved special studs. – Never use studs that exceed the height of your snowmobile’s track profile by more than 9.5 mm (3/8 in).
Page 47 TRACTION ENHANCING PRODUCTS WARNING – See an authorized Ski-Doo dealer for current specific stud- ding availability and applications. – DO NOT EVER use conventional stud because, the track thickness is thinner then our standard tracks and the stud could tear off of track and separate from vehicle.
Page 48: Maintenance/Replacement
TRACTION ENHANCING PRODUCTS Maintenance/Replacement PROCEED WITH A VISUAL INSPECTION OF YOUR TRACK BEFORE EACH USE. Look for any defects, such as: – Perforations in the track – Tears in the track (particularly around traction holes on studded tracks) – Lugs that are broken or torn off, exposing portions of rods –...
Page 49: Moving Loads And Doing Work
Your vehicle can help you perform a number of different LIGHT tasks ranging from pulling a load to carrying cargo. A variety of accessories are available from your authorized Ski-Doo dealer. To prevent possible injury, follow the instructions and warnings that accompany the accessory.
Page 50: Hauling A Load
MOVING LOADS AND DOING WORK MAXIMUM LOAD TABLE Evenly distributed. CARGO Includes rear rack, rear 16 kg (35 lb) LOAD models storage compartment and tongue load. Hauling a Load Never pull a load by attaching it directly to the bumper. Use only the hitch to pull a load.
Page 51 MOVING LOADS AND DOING WORK Reduce your speed when pulling a cargo carrier and turn gradually. Avoid hills and rough terrain. Never attempt steep hills. Allow more distance for braking, especially on inclined surfaces and when a pas- senger is on board. Be careful not to skid or slide. Improperly loading a cargo carrier may cause a loss of control.
Page 52: Important On-Product Labels
IMPORTANT ON-PRODUCT LABELS Hang Tag(s) 704901107 vmo2006-005-009_en TYPICAL ____ ____ SAFETY INFORMATION...
Page 53: Important On-Product Labels (Cont'd)
IMPORTANT ON-PRODUCT LABELS . Operating, servicing and WARNING maintaining an off-road vehicle can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
Page 54 IMPORTANT ON-PRODUCT LABELS mmo2010-003-100_en ____ ____ SAFETY INFORMATION...
Page 55: Vehicle Safety Labels
The following labels are on your vehicle and they should be consid- ered permanent parts of the vehicle. If missing or damaged, the decals can be replaced free of charge. See an authorized Ski-Doo dealer. NOTE: In the event of any discrepancy between this guide and the vehicle, the safety labels on the vehicle have precedence over the la- bels in this guide.
Page 56 IMPORTANT ON-PRODUCT LABELS NEVER SIT IN CARGO AREA ability and cause permanent damage. MAXIMUM cargo load (including tongue weight): 15,8 kg (35 lb) 155 N MAXIMUM towing capacity: 260 kg (573 lb) 2550 N 10575 EN-516010575-DEC Before studding this track, consult the Operator`s Guide included with this vehicle for all details pertaining to track studding.
Page 57 IMPORTANT ON-PRODUCT LABELS mmo2008-003-007 LABEL 5 ____ SAFETY INFORMATION...
Page 58 IMPORTANT ON-PRODUCT LABELS EN-516007667A-DEC LABEL 6 ____ ____ SAFETY INFORMATION...
Page 59 IMPORTANT ON-PRODUCT LABELS Always electrically disconnect both fuel injectors prior to testing for ignition spark. Otherwise, fuel vapors may ignite in presence of a spark creating a fire hazard. 516007661 EN-516007661-DEC LABEL 7 ____ SAFETY INFORMATION...
Page 60 IMPORTANT ON-PRODUCT LABELS EN-516010577-DEC LABEL 8 ____ ____ SAFETY INFORMATION...
Page 61 IMPORTANT ON-PRODUCT LABELS EN-516010578-DEC LABEL 9 ____ SAFETY INFORMATION...
Page 62 IMPORTANT ON-PRODUCT LABELS EN-516007652-DEC LABEL 10 • This shock absorber is pressurized. • An explosion may occur if heated or punctured. • Do not disassemble. mmo2010-003-101_en LABEL 11 - ON GAS CHARGED SHOCK ABSORBERS ____ ____ SAFETY INFORMATION...
Page 63 IMPORTANT ON-PRODUCT LABELS RU-516009934-DEC LABEL 12- MODELS IN EURASIAN UNION ONLY ____ SAFETY INFORMATION...
Page 64: Compliance Labels
IMPORTANT ON-PRODUCT LABELS Compliance Labels 520001663-102_c EPA Compliance Label EMISSION CONTROL INFORMATION THIS VEHICLE IS CERTIFIED TO OPERATE ON XXXX UNLEADED GASOLINE AND MEETS U.S. EPA REGULATIONS FOR SNOWMOBILE SI ENGINES. ENGINE FAMILY XXXXXXXXXXXX FAMILLE DE MOTEUR XXXXXXXXXXXX PERMEATION FAMILY FAMILLE DE PERMÉATION XX g/kW-hr HC LIMITE DES ÉMISSIONS...
Page 65 IMPORTANT ON-PRODUCT LABELS SSCC Label Safety standards for snowmobiles have been adopted by the Snow- mobile Safety and Certification Committee (SSCC) of which BRP is a proud participating member. Assurance that your snowmobile meets these standards is easily checked by locating the Certification Label on a right vertical portion of the vehicle.
Page 66 IMPORTANT ON-PRODUCT LABELS Regulation (EU) 2016/1628 applicable for Non-Road Mobile Machineries Vehicles who comply to Regulation (EU) 2016/1628 (NRMM) are identified on the engine valve cover. NRMM_ACE_MY20 TYPICAL Rotax NRSC H CO2 g/kWh: XXXX MXXXXXXX MM-YYYY Prod. date: Family type: XXXXXX SMB/P V-#### EN-516010559-DEC...
Page 67 IMPORTANT ON-PRODUCT LABELS Depending on your particular vehicle configuration, an additional NRMM identification decal may be installed on the tunnel, near the chaincase. 520002114-103 TYPICAL - ON RH SIDE OF TUNNEL Bombardier Recreational Products Inc. 565 de la Montagne, Valcourt,QC, Canada J0E 2L0 BRP Europe N.V.
Page 68: Technical Information Labels
IMPORTANT ON-PRODUCT LABELS Technical Information Labels – Install Suspension adjustment tool 1st (illustrated Red on label). – Install Pulley Expander and Headlight adjustment tool 2nd (illus- trated Blue on label). – Refer to your operator's guide. 516009984 EN-516009984-DEC LOCATED ON BELT GUARD DEC 513033942 EN-FR LOCATED ON FUEL CAP - ON 600 ACE AND 900 ACE ENGINE (IN COUNTRIES USING RON OCTANE RATINGS)
Page 69 IMPORTANT ON-PRODUCT LABELS OCTANE mmo2013-002-003 LOCATED ON FUEL CAP - ON 600 ACE AND 900 ACE ENGINE (IN COUNTRIES USING PUMP POSTED AKI (RON+MON)/2 OCTANE RATINGS) DEC 513033943 EN-FR ON FUEL CAP - ON TURBO ENGINES (IN COUNTRIES USING RON OCTANE RATINGS) ____ SAFETY INFORMATION...
Page 70 IMPORTANT ON-PRODUCT LABELS OCTANE mmo2013-002-002 ON FUEL CAP - ON TURBO ENGINES (IN COUNTRIES USING PUMP POSTED AKI (RON+MON)/2 OCTANE RATINGS) ____ ____ SAFETY INFORMATION...
Page 71: Reporting Safety Defects
REPORTING SAFETY DEFECTS In Canada, if you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Transport Canada in addition to notifying Bombardier Recre- ational Products Inc. If Transport Canada receives similar complaints, it may open an inves- tigation, and if it finds that a safety defect exists in a group of vehi- cles, it may order a recall and remedy campaign.
Page 72 REPORTING SAFETY DEFECTS This page is intentionally blank ____ ____ SAFETY INFORMATION...
Page 73: Vehicle Information
VEHICLE INFORMATION __________________...
Page 74: Controls, Instruments And Equipment
CONTROLS, INSTRUMENTS AND EQUIPMENT Some features may not apply to your model or could be optional. Some vehicle safety labels are not shown on illustrations. For infor- IMPORTANT ON-PRODUCT mation on vehicle safety labels, refer to LABELS 520002409-004 TYPICAL - MODELS WITHOUT LARGE PANORAMIC 7.8" WIDE LCD DISPLAY __________________...
Page 75 CONTROLS, INSTRUMENTS AND EQUIPMENT 520002409-001 MODELS WITH A LARGE PANORAMIC 7.8" WIDE LCD DISPLAY 520002114-101 __________________...
Page 76: Handlebar
CONTROLS, INSTRUMENTS AND EQUIPMENT Handlebar The handlebar controls the steering of the snowmobile. As the han- dlebar is rotated to right or left, the skis are turned right or left to steer the snowmobile. WARNING Fast reverse while turning, could result in loss of stability and control.
Page 77 CONTROLS, INSTRUMENTS AND EQUIPMENT WARNING Test the throttle lever operation each time before starting the engine. The lever must return to the rest position once released. Otherwise, do not start engine. Switching from Thumb to Finger Throttle Position CAUTION It is highly recommended to immobilize the snowmobile before attempting any modification to the throttle position as it could lead to a hazardous situation.
Page 78 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2015-008-100_a IF WANTED, CONTINUE TO ROTATE THE THROTTLE HOUSING mmo2015-008-101 FINGER THROTTLE POSITION __________________...
Page 79: Brake Lever
CONTROLS, INSTRUMENTS AND EQUIPMENT CAUTION – It is HIGHLY recommended to use gloves and NOT mitts when using the finger throttle position. – It is not recommended to use the finger throttle position while riding in dense off trail areas. The procedure to go back to the thumb throttle position is the reverse of the one shown above.
Page 80: Parking Brake Lever
CONTROLS, INSTRUMENTS AND EQUIPMENT Parking Brake Lever Parking brake lever is located on the LH side of handlebar. Parking brake should be used whenever snowmobile is parked. mmo2014-004-001_b TYPICAL 1. Parking brake lever WARNING Make sure parking brake is fully disengaged before operating the snowmobile.
Page 81: Engine Cut-Off Switch
CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2009-005-006_a TYPICAL — ENGAGE MECHANISM Step 1: Apply and hold brake Step 2: Lock brake lever using parking brake lever To Release Parking Brake Squeeze brake lever. Parking brake lever will automatically return to its original position. Always release parking brake before riding. Engine Cut-off Switch The engine cut-off switch (tether cord) is located on the console.
Page 82 The D.E.S.S. key contains an electronic chip which features a unique permanently memorized digital code. Your authorized Ski-Doo dealer has programed the D.E.S.S. of your snowmobile to recognize the D.E.S.S. key in the tether cord cap to al- low vehicle operation.
Page 83: Eco/Standard/Sport Modes (On Applicable Models)
CONTROLS, INSTRUMENTS AND EQUIPMENT Eco/Standard/Sport Modes (On Applicable Models) The Eco/Standard/Sport switch is located on the console to the left of the steering column. 520001896-013_a 1. Sport mode 2. Standard mode 3. Eco mode __________________...
Page 84: Emergency Engine Stop Switch
CONTROLS, INSTRUMENTS AND EQUIPMENT Emergency Engine Stop Switch The emergency engine stop switch is located on the RH side of han- dlebar. Push-pull type switch. To stop the engine in an emergency, select OFF position (down) and simultaneously apply the brake. To restart, button must be at the ON position (up).
Page 85 WARNING If the switch has been used in an emergency caused by a suspected malfunction, the source of the malfunction should be determined and corrected before restarting engine. See an authorized Ski-Doo dealer for servicing. __________________...
Page 86: Adjustable Handlebar Riser (If Equipped)
CONTROLS, INSTRUMENTS AND EQUIPMENT Adjustable Handlebar Riser (If Equipped) WARNING Always stop engine before adjusting handlebar. The handlebar can be set in four different positions. To change handlebar position, pull lever and position handlebar as de- sired. 520001663-014_a TYPICAL Move the handlebar back and forth to make sure mechanism is se- curely engaged.
Page 87: Handlebar Multifunction Switch
CONTROLS, INSTRUMENTS AND EQUIPMENT Handlebar Multifunction Switch Multifunction switch is located on the LH side of handlebar. mmo2014-004-001_c TYPICAL - MODELS WITHOUT THE LARGE PANORAMIC 7.8" WIDE LCD DISPLAY 1. Start/Electronic Reverse button 2. Headlights dimmer switch 3. Heated grips switch 4.
Page 88 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2014-004-001_c MODELS WITH THE LARGE PANORAMIC 7.8" WIDE LCD DISPLAY 1. Start/Electronic Reverse button 2. Headlights dimmer switch 3. Heated grips switch 4. Heated throttle lever switch 5. Audio Control and Phone call control __________________...
Page 89 CONTROLS, INSTRUMENTS AND EQUIPMENT Start/Electronic Reverse (RER) Button 520001899-210_a 1. Start / RER button ENGINE On electric start models, press to start engine. Refer to STARTING PROCEDURE BASIC PROCEDURES Once engine is started, press to engage the electronic reverse. Re- REVERSE (RER) BASIC PROCEDURES fer to...
Page 90 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2014-004-001_d VARIABLE INTENSITY 1. Heated grip switch 2. Increase heat 3. Decrease heat The heating intensity is displayed via the digital display. __________________...
Page 91 CONTROLS, INSTRUMENTS AND EQUIPMENT 619900974-707 MODELS WITHOUT THE LARGE PANORAMIC 7.8" WIDE LCD DISPLAY SHOWN 1. Heated grip icon 2. More heat 3. Less heat There are ten intensity settings. When released, display will return to fuel level. Heated grips will be in OFF position when there are no bars displayed on the gauge.
Page 92 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2014-004-001_e VARIABLE INTENSITY 1. Heated throttle lever switch 2. Increase heat 3. Decrease heat __________________...
Page 93 CONTROLS, INSTRUMENTS AND EQUIPMENT 619900974-708 MODELS WITHOUT THE LARGE PANORAMIC 7.8" WIDE LCD DISPLAY SHOWN 1. Heated grip icon 2. More heat 3. Less heat There are ten intensity settings. When released, display will return to engine temperature. Heated throttle lever will be in OFF position when there are no bars displayed on the gauge.
Page 94 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2014-004-001_f MENU/SET BUTTON 1. Menu function 2. SET function GAUGE Refer to for complete information. Audio Volume Control Models with the Large Panoramic 7.8" Wide LCD Display This button is used to manage the information displayed on the mul- tifunction gauge or answer/cancel a phone call.
Page 95: 10) Seat
CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2014-004-001_f 1. Volume DOWN/Cancelling a call 2. Volume UP/Answering a call LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Refer to section for complete information. 10) Seat Seat Removal While pushing in the center of the seat towards front, pull on both sides.
Page 96 CONTROLS, INSTRUMENTS AND EQUIPMENT 520001899-200_a Step 1: Push Step 2: Pull Step 3: Lift up and backward to unlock seat Slide seat rearwards to remove it. Seat Installation NOTICE Riding the vehicle with any objects between the seat and the fuel tank could damage the fuel tank. NEVER place any objects between seat and fuel tank.
Page 97: 11) Front And Rear Bumpers
CONTROLS, INSTRUMENTS AND EQUIPMENT 520001896-001_b WARNING Make sure seat is securely latched before riding. 11) Front and Rear Bumpers To be used whenever snowmobile requires manual lifting. CAUTION Beware of injuries by using proper lifting tech- niques, notably using your legs force. Do not attempt to lift the rear of vehicle if it is above your limits.
Page 98 CONTROLS, INSTRUMENTS AND EQUIPMENT 520001899-002_a 1. Front bumper 520001663-005_a TYPICAL 1. Rear bumper NOTICE Do not use skis to pull or lift snowmobile. __________________...
Page 99: 12) Storage Compartment
CONTROLS, INSTRUMENTS AND EQUIPMENT 12) Storage Compartment A storage compartment is located at the front of the vehicle, above the gauge. The Operator's Guide and the emergency starter rope are in the front storage compartment. To open, push the button and lift the cover. 619900974-004 TYPICAL NOTE: When closing, make sure cover is secured properly.
Page 100: 13) Operator's Guide
CONTROLS, INSTRUMENTS AND EQUIPMENT 520001896-003_a 1. Storage compartment 2. Latch 3. Battery cover 13) Operator's Guide STORAGE COMPART- The Operator's Guide should be stored in the MENT 14) Rotary Control The rotary control is located on the left side of the console. __________________...
Page 101 CONTROLS, INSTRUMENTS AND EQUIPMENT 520002409-006 It is used to navigate into the LCD display and control the audio sys- tem. – Seek/Play/Pause buttons allow to control volume and music listened in the helmet audio system. – The center knob can be used to navigate inside menu or select and set settings.
Page 102 CONTROLS, INSTRUMENTS AND EQUIPMENT 520002409-007 1. Audio control 2. Center knob 3. Vehicle data button 4. BRP Connect When audio source is selected, the Preset/Seek buttons work as fol- low: – Short press: Previous or Next Preset – Long press: Seek - up or down When Bluetooth audio source is selected, the Preset/Seek buttons work as follow: –...
Page 103: 15) Drive Belt Guard
CONTROLS, INSTRUMENTS AND EQUIPMENT 15) Drive Belt Guard Drive Belt Guard Removal WARNING NEVER operate engine: – Without shields and belt guard securely installed. – With hood and/or side panels opened or removed. NEVER attempt to make adjustments to moving parts while engine is running.
Page 104 CONTROLS, INSTRUMENTS AND EQUIPMENT Drive Belt Guard Installation Insert the tab into the slot and push belt guard toward engine into place. 520001899-211_a Step 1: Lower belt guard Step 2: Slide belt guard Position the rear portion of the belt guard over the retainer and secure it using the retaining pin.
Page 105: 16) Tools
CONTROLS, INSTRUMENTS AND EQUIPMENT 520001897-003_a 16) Tools A part of the drive belt guard is designed to hold the tools allowing for basic maintenance. The tools are supplied with the vehicle. They should always be installed in their proper location and orientation _________________...
Page 106 CONTROLS, INSTRUMENTS AND EQUIPMENT 520001897-001_a TYPICAL - DRIVE BELT GUARD TOOLS LOCATION 1. Suspension adjustment tool 2. Pulley expander Install in the following sequence: 1. Slide the Suspension adjustment tool open end under retaining tab. 2. Press the closed end on the retaining tabs. 3.
Page 107 CONTROLS, INSTRUMENTS AND EQUIPMENT 520002104-500 520002104-501 _________________...
Page 108: 17) Spare Drive Belt Holder
CONTROLS, INSTRUMENTS AND EQUIPMENT 520001798-008 PULLEY EXPANDER 520001663-022 SUSPENSION ADJUSTMENT TOOL 17) Spare Drive Belt Holder A spare drive belt can be stored in a holder located on the drive belt guard. NOTE: The spare drive belt is not supplied with the snowmobile. Position spare drive belt into drive belt guard slot.
Page 109 CONTROLS, INSTRUMENTS AND EQUIPMENT 520001897-002_a TYPICAL 1. Drive belt guard 2. Slot Secure in place by sliding it behind the tabs. 520001897-002_b TYPICAL _________________...
Page 110: Upper Body Module (Hood)
CONTROLS, INSTRUMENTS AND EQUIPMENT 18) Upper Body Module (Hood) Upper Body Module Removal 1. Open the storage compartment. 619900974-004 _________________...
Page 111 CONTROLS, INSTRUMENTS AND EQUIPMENT 2. Remove the gauge retaining screws. 619900974-008 _________________...
Page 112 CONTROLS, INSTRUMENTS AND EQUIPMENT 3. Lift the front of the gauge support, then slide it forward to remove 619900974-009 4. Set gauge support aside. _________________...
Page 113 CONTROLS, INSTRUMENTS AND EQUIPMENT 5. Remove the storage compartment. 520001663-017_a 6. Disconnect the MAPTS and headlight connectors. mmr2017-051-012 _________________...
Page 114 CONTROLS, INSTRUMENTS AND EQUIPMENT 7. Loosen the air intake duct clamp. 520001663-026_a 1. Clamp 8. Remove the upper body module retaining screws on both sides. mmr2017-051-014_a _________________...
Page 115 CONTROLS, INSTRUMENTS AND EQUIPMENT 9. Free the rear end hooks of the upper body module from the slots in the console. 520001899-207_a 10. Remove the upper body module. 10.1 Grab the upper body module in the gauge support area. 10.2 Pull the module forward.
Page 116 CONTROLS, INSTRUMENTS AND EQUIPMENT mmr2017-051-016 2. Lower the rear end of the upper body module. 3. Insert the rear end hooks of the upper body module into the slots in the console. NOTE: Make sure the air intake duct is properly connected. 4.
Page 117: 19) Side Panels
CONTROLS, INSTRUMENTS AND EQUIPMENT 19) Side Panels WARNING Never operate engine with side panels opened or removed from vehicle. Side Panels Opening and Closing Unlock all latches, then open panel. 520001896-022_a When closing panel, make sure latches are locked securely. Side Panels Removal Open side panel.
Page 118: Reverse (Mechanical) (If Equipped)
CONTROLS, INSTRUMENTS AND EQUIPMENT mmr2017-051-003_a 20) Reverse (Mechanical) (if equipped) 619900974-003 TYPICAL _________________...
Page 119: Heated Seats Switches (If Equipped)
CONTROLS, INSTRUMENTS AND EQUIPMENT BASIC PROCEDURES Refer to for proper operation. 21) Heated Seats Switches (if equipped) The heated seat switch is located on the console to the left of the steering column. 520001896-013_a HEATED SEAT SWITCH 1. Hi 2. OFF 3.
Page 120: Horn Button (Not Illustrated On Vehicle)
CONTROLS, INSTRUMENTS AND EQUIPMENT 22) Horn Button (Not illustrated on vehicle) For vehicles sold in Finland Press on the horn button (mounted on handlebar) to activate the horn. 520002346-003 TYPICAL _________________...
Page 121: 4.5" Digital Display
4.5" DIGITAL DISPLAY Multifunction Display Lower Display 619900974-706 619900974-700 May display the following: – RPM – Speed – Engine Temperature – Fuel Statistics – Settings – Messages – Outside temperature (if equipped) Use LOWER button to change the displayed information. _________________...
Page 122 4.5" DIGITAL DISPLAY The SPEED STAT display shows the maximum and the averaged speed. Hold LOWER button for 3 seconds to reset. When the SPEED display is chosen, the RPM is shown in the TRIP display. Left Lateral Display 619900974-701 The left lateral display includes: –...
Page 123 4.5" DIGITAL DISPLAY Central Display 619900974-703 Display the RPM of the engine or the vehicle speed in Km/h or MPH. MODE Display (ACE engines, if equipped) 619900974-704 The MODE display indicates the selected mode of operation: – SPORT – ECO –...
Page 124: Warning Lamps And Indicators
4.5" DIGITAL DISPLAY DRIVE MESSAGE AT MESSAGE AT MODE ACTIVATION DEACTIVATION Sport Sport Sport OFF Eco OFF Trip Display 619900974-705 This display shows trip informations: – Cumulative distance odometer – Trip A hours – Trip A distance (Km or mph) –...
Page 125 4.5" DIGITAL DISPLAY Telltale Lights - Lower Bar 219100975-004 LIGHTS DESCRIPTION ORANGE - Vehicle malfunction BLUE - The high beam are selected RED - The engine temperature is too high. RED - Parking brake is engaged or malfunction of the brake system RED - The battery voltage too low or problem with the electrical system RED - Low engine oil pressure (if applicable)
Page 126: Settings
4.5" DIGITAL DISPLAY Icons and Indicators - Multifunction Display ICONS AND INDICATORS Denotes SPORT mode is selected. Denotes ECO mode is selected. Settings Setup 520002114-102 1. Upper button (S) 2. Lower button (M) Using LOWER button, select SETTINGS and hold to enter setting menu.
Page 127 7. Press LOWER button to switch to minutes (minutes flash). 8. Push and hold LOWER button to acknowledge minutes selection. Setting Language The gauge display language can be changed. Refer to an authorized Ski-Doo dealer for language availability and to setup the gauge to your preference. _________________...
Page 128: 7.2" Digital Display
7.2" DIGITAL DISPLAY Multifunction Display 619900975-500 619900975-006 MENU (M) BUTTON _________________...
Page 129 7.2" DIGITAL DISPLAY 619900975-007 SET (S) BUTTON 1. Select the upper or center display by using the MENU (M) button on the multifunction switch. 619900975-006 MENU (M) BUTTON 2. While the desired display is flashing, navigate through the display, by using the SET (S) button on the multifunction switch. _________________...
Page 130 7.2" DIGITAL DISPLAY 619900975-007 SET (S) BUTTON Once the desired information is displayed, press the MENU (M) but- ton or wait 5 seconds to confirm. 619900975-006 MENU (M) BUTTON To reset – Average speed – Top speed – Total fuel consumption _________________...
Page 131 7.2" DIGITAL DISPLAY Press and hold the SET (S) button while display is flashing. Lower Display 619900975-501 May display the following: – Settings – Messages The SPEED display shows the Maximum and the averaged speed. Hold MENU button for 3 seconds to reset. Left Lateral Display 619900975-502 The left lateral display includes:...
Page 132 7.2" DIGITAL DISPLAY – Trip distance A and B (Km or mph) – Cumulative hours – Speed – RPM – Odometer 619900975-004 _________________...
Page 133 7.2" DIGITAL DISPLAY 619900974-802 HEATING INTENSITY DISPLAY 1. Heated Grip icon 2. More heat 3. Less heat Right Lateral Display 619900975-503 _________________...
Page 134 7.2" DIGITAL DISPLAY The right lateral display includes: – Engine Temperature – Heated throttle indicator – Clock 619900975-005 _________________...
Page 135 7.2" DIGITAL DISPLAY 619900974-803 Central Display 619900975-504 _________________...
Page 136 7.2" DIGITAL DISPLAY Display the vehicle speed in Km/h (or MPH) or the RPMs. Refer to SETTINGS mmo2014-004-001_h TYPICAL 1. MODE (M) button ACS Suspension Position Display (if equipped) 619900975-505 This display shows suspension setting. The suspension is calibrated from 1 to 5, 1 being the softest setting. _________________...
Page 137 7.2" DIGITAL DISPLAY 619900974-805 TUNE YOUR RIDE Refer to section for proper adjustment procedure. MODE Display (ACE engines, if equipped) 619900975-506 The MODE display indicates the selected mode of operation: – SPORT – ECO – NORMAL _________________...
Page 138: Warning Lamps And Indicators
7.2" DIGITAL DISPLAY 619900974-804 NOTE: When in NORMAL mode, no information is displayed. A message of the selected mode will be displayed on the lower dis- play at activation and deactivation as follow: DRIVE MESSAGE AT MESSAGE AT MODE ACTIVATION DEACTIVATION Sport Sport...
Page 139 7.2" DIGITAL DISPLAY Telltale Lights - Lower Bar 219100975-004 LIGHTS DESCRIPTION ORANGE - Vehicle malfunction BLUE - The high beam are selected RED - The engine temperature is too high. RED - Parking brake is engaged or malfunction of the brake system RED - The battery voltage too low or problem with the electrical system RED - Low engine oil pressure (if applicable)
Page 140: Settings
7. Push MENU button to switch to minutes (minutes flash). 8. Press MENU button to change minutes. Setting Language The gauge display language can be changed. Refer to an authorized Ski-Doo dealer for language availability and to setup the gauge to your preference. _________________...
Page 141: Large Panoramic 7.8" Wide Lcd Display
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Basic Functions LCD Display Default Display WideLCDDisplay1 Multifunction Display WideLCDDisplay2 Left Lateral Display The left lateral display includes: – Fuel level indicator – Engine temperature – Speedometer – Tripmeter – Rpm – Clock _________________...
Page 142 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY – Driving modes – Warning pop-up LeftScreenSki1 PRINCIPAL VIEW – Heated grips – Heated thumb _________________...
Page 143 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY LeftScreenSki2 SECONDARY VIEW - HEATED ELEMENTS To select the value to be displayed in the tripmeter; 1. Access the Stats/Trip screen 2. Select and activate the desired set of statistic to be shown (Trip A, Trip B or Total) Right Lateral Display The right lateral display includes:...
Page 144 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY RightScreenSki2 STATS/TRIPS VIEW _________________...
Page 145 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY RightScreenSki1 SETTINGS VIEW Navigating in the Digital Display WARNING Reading or tampering with the multifunction gauge can dis- tract you from the operation of the vehicle, particularly from constantly scanning the environment. Always pay attention to road conditions, ensure your environment is clear and free from obstacles.
Page 146 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Pressing the center knob will get the Menu selection in the right screen, in this order: – BRP Connect – Phone – Statistics – Audio – Settings When an icon is selected, its related screen will appear. RightScreenSki1 SETTINGS VIEW When an item is selected, this sets the item to the current value.
Page 147 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Indicator Lamps Telltale Lights - Lower Bar 219100975-004 LIGHTS DESCRIPTION ORANGE - Vehicle malfunction BLUE - The high beam are selected RED - The engine temperature is too high. RED - Parking brake is engaged or malfunction of the brake system RED - The battery voltage too low or problem with the electrical system...
Page 148 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Icons and Indicators - Multifunction Display ICON DESCRIPTION Smartphone Network connection Bluetooth device Smartphone battery level indicator Helmet pairing indicator Fuel indicator Temperature indicator Helmet audio output _________________...
Page 149: Settings
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Settings Menu BRP Connect BRP connect_test Before using BRP Connect, the app must be downloaded to the phone. The app can be downloaded from the Apple App Store or Google Play Store via a simple search. Not all phones are compati- ble.
Page 150 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Phone Phone_a The phone menu is to access: – The phone history – The phone contact list NOTE: To have access to the Phone menu, a phone and rider helmet PAIR YOUR SMARTPHONE VIA BLUE- must be paired.
Page 151 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Statistics RightScreenSki2 The Statistics menu is used to get : – Trip distance information – Trip elapsed time information – Instant fuel consumption – Average fuel consumption – Maximum speed – Average speed 3 sets of statistics are kept in memory. Each set of statistic can be reset independently.
Page 152 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Audio Allow to control volume and music listened in the helmet audio sys- tem. Gives also song informations when available. Settings RightScreenSki1 The Settings menu is to: – Adjust clock – Pair Bluetooth devices •...
Page 153: Pairing Your Smartphone Via Bluetooth
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY – Get information about firmware version and device regulatory compliance – Show vehicle fault codes. Pairing your Smartphone Via Bluetooth On the vehicle 1. Short press the rotary control knob to access menu. 2. Go to “Settings” and move the knob RIGHT. 3.
Page 154 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY 2) Download Apps Compatible With BRP Connect Visit our website to know more about the compatible apps. These apps will improve your riding experience. Some apps may require additional purchase to be compatible with the system or may require additional devices to be used.
Page 155: Quick Tour Of The Brp Connect App
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Quick Tour of the BRP Connect App 219002011-500 _________________...
Page 156 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY 1. News: Communications may occasionally be issued through the BRP Connect app and can be found through this menu. 2. Vehicle Finder: Allows you to store the location of your vehicle (or any other location you wish to remember). The feature is rel- atively rich as it also allows you to take a picture of the location you left your vehicle at, take notes (e.g.
Page 157 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY 219002011-501 1. Currently Installed Apps 2. Available Apps _________________...
Page 158: Messages In Multifunction Gauge
LIMP HOME. If you operate the vehicle in LIMP HOME, avoid abrupt maneuvers and immediately go to the nearest authorized Ski-Doo dealer to have your vehicle serviced before riding again. In LIMP HOME, the engine RPM is limited and therefore the vehicle speed.
Page 159 LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Important information messages can also be displayed temporarily to assist indicator lamps. When a digital warning appears, it will show the warning for 6 sec- onds and then the warning will disappear for 60 seconds. During the 60 seconds, the small digital indicator will flash.
Page 160: Fuel And Oil
FUEL AND OIL Fuel Requirements NOTICE Always use fresh gasoline. Gasoline will oxidize; the result is loss of octane, volatile compounds, and the production of gum and varnish deposits which can damage the fuel system. Alcohol fuel blending varies by country and region. Your vehicle has been designed to operate using the recommended fuels, however, be aware of the following: –...
Page 161: Fueling Procedure
FUEL AND OIL NOTICE Never experiment with other fuels. Engine or fuel sys- tem damages may occur with the use of an inadequate fuel. NOTICE Do NOT use fuel from fuel pumps labeled E85. Use of fuel labeled E15 is prohibited by U.S. EPA Regulations. Fueling Procedure WARNING Always stop engine before refueling.
Page 162 FUEL AND OIL 520001899-003_a TYPICAL 1. Fuel tank cap 4. Insert the spout into the filler neck. 5. Pour fuel slowly so that air can escape from the tank and prevent fuel flow back. Be careful not to spill fuel. 6.
Page 163: Recommended Oil
FUEL AND OIL Recommended Oil Rotax ® engines were developed and validated using the XPS™ oil. BRP recommends the use of its XPS engine oil or an equivalent at all time. Do not add any oil additives to the recommended engine oil. Damages caused by the use of an oil not suitable for the engine or by adding of an oil additives may not be covered by the BRP Limited Warranty.
Page 164: Break-In Period
BREAK-IN PERIOD Operation During Break-In Engine During the break-in period: – Avoid prolonged full throttle operation. – Avoid sustained accelerations. – Avoid prolonged cruising speeds. – Avoid engine overheating. However, brief accelerations and speed variations contribute to a good break-in. During a predetermined period, the engine management system controls some engine parameters.
Page 165: Operating Modes
OPERATING MODES WARNING Whenever changing operating mode, make sure to maintain situational awareness while riding. ECO Mode (Fuel Economy Mode) When ECO mode is selected (fuel economy mode), vehicle torque and speed are limited whereby an optimal cruising speed is main- tained in order to reduce fuel consumption.
Page 166: Navigating Operating Modes
OPERATING MODES Navigating Operating Modes Use ECO/Standard/Sport Mode switch to navigate between power levels, from ECO (reduced power) to Standard (full power) to Sport (increased response). To increase power, press the switch upwards. To decrease power, press the switch downwards. 520001899-004_a TYPICAL - LH SIDE OF FUEL TANK 1.
Page 167 OPERATING MODES To activate Sport mode when in ECO mode, press top end of switch twice. To activate Standard mode when in ECO mode, press top end of switch once. WARNING When adjusting modes, be sure to maintain situational aware- ness of other snowmobiles, obstacles, or persons.
Page 168: Basic Procedures
BASIC PROCEDURES Engine Starting Procedure Procedure 1. Apply parking brake. 2. Recheck throttle control lever operation. 3. Put your helmet on. 4. Ensure that the tether cord cap is installed on the engine cut-off switch and that the cord is attached to your clothing eyelet. 5.
Page 169 BASIC PROCEDURES 4. Apply throttle until drive pulley engages. Drive at low speed the first two or three minutes. NOTICE If vehicle does not move when throttle is applied, stop engine, remove tether cord cap from the engine cut-off switch, then do the following.
Page 170 BASIC PROCEDURES 520001899-005_a 1. Reverse lever 520001899-210_a 1. Start / RER ( electro mechanical ) button _________________...
Page 171: Shifting In Forward
BASIC PROCEDURES WARNING Engaging the reverse mode is done by depressing the RER but- ton when the engine is running. Wait until the reverse alarm sounds and the RER pilot lamp comes on in the analog/digital gauge before operating throttle to proceed in reverse. The reverse speed is not limited.
Page 172: Riding Conditions And Your Snowmobile
FACTORY CALIBRATION Sea level up to 600 m (2,000 ft) If your snowmobile is to be used at an altitude outside the specified range, have it calibrated accordingly by an authorized Ski-Doo dealer. NOTICE An inappropriate altitude calibration would decrease performance and may cause serious damage to the snowmo- bile.
Page 173: Special Operation
SPECIAL OPERATION Towing an Accessory Always use a rigid tow bar to tow an accessory. Any towed acces- sory should have reflectors on both sides and at the rear. Check local laws for brake light(s) requirements. WARNING Never tow an accessory with a rope. Always use a rigid tow bar.
Page 174: Tune Your Ride
TUNE YOUR RIDE Snowmobile handling and comfort depend upon multiple adjust- ments. WARNING Suspension adjustment could affect vehicle handling. Always take time to familiarize yourself with the vehicle's behavior af- ter any suspension adjustment have been made. Always ad- just LH and RH suspension components to the same setting. Choice of suspension adjustments vary with carrying load, operator's weight, personal preference, riding speed and field condition.
Page 175: Ski Runner Depth Setting (Pilot Ts Skis)
TUNE YOUR RIDE Ski Runner Depth Setting (Pilot TS Skis) Pilot TS skis enables the rider to dial in the amount of ski bite for con- ditions and riding style. A knob adjacent to the ski leg raises or lowers the ski runner. Ski behavior depends largely on trail conditions but also on ski run- ner adjustment.
Page 176: Rear Suspension Adjustments
TUNE YOUR RIDE PILOT TS SKI ADJUSTABILITY Lateral Possible Possible Position Handling grip understeering oversteering **** **** ***** ***** Rear Suspension Adjustments 520002346-001 rMOTION X WITH QUICK ADJUST- ADJUSTABLE COMPONENTS 1. Stopper strap 2. Center spring 3. Rear spring 4. Rear shock absorber 5.
Page 177 TUNE YOUR RIDE 520002316-008 rMOTION AND rMOTION-X WITHOUT QUICK ADJUST- ADJUSTABLE COMPONENTS 1. Stopper strap 2. Center spring 3. Center shock absorber 4. Rear spring 5. Rear shock absorber 6. Coupling blocks (RH side shown) 7. rear shock lower pivot (rMotion and rMotion-X) 8.
Page 178 TUNE YOUR RIDE Stopper Strap Stopper strap length has an effect on the amount of weight the cen- ter spring has to carry especially during acceleration, therefore on the front end uplift. Stopper strap length also has an effect on center spring travel. NOTICE Whenever stopper strap length is changed, track ten- sion must be checked.
Page 179 TUNE YOUR RIDE mmo2015-007-102_b STOPPER STRAP POSITION 1 (1ST HOLE, LONGEST) 1. 1st hole from end 2. Towards rear 3. Tip of strap touching strap axis 4. Two holes left open between screw head and nut 5. Towards front _________________...
Page 180 TUNE YOUR RIDE mmo2015-007-101_b STOPPER STRAP POSITION 2 (2ND HOLE) 1. Free hole 2. 2nd hole from end 3. Towards rear 4. Tip of strap touching strap axis 5. Two holes left open between screw head and nut 6. Towards front _________________...
Page 181 TUNE YOUR RIDE mmo2015-007-103_b STOPPER STRAP POSITION 3 (3RD HOLE) 1. Free holes 2. 3rd hole from end 3. Towards rear 4. Tip of strap touching strap axis 5. Two holes left open between screw head and nut 6. Towards front NOTE: Decreasing the stopper strap length may reduce comfort.
Page 182 TUNE YOUR RIDE Center Spring Center spring preload has an effect on steering effort, handling and bump absorption. Also, since center spring preload adjustment puts more or less pres- sure on the front of the track, it has an effect on the performance in deep snow.
Page 183 TUNE YOUR RIDE mmo2010-003-015_a TYPICAL- CAM TYPE 1. Spring preload adjustment cam 2. Decrease preload 3. Increase preload _________________...
Page 184 TUNE YOUR RIDE mmo2012-005-807_b TYPICAL- RING TYPE 1. Spring preload adjustment ring 2. Increase preload 3. Decrease preload NOTE: Use the suspension adjustment tool provided with the vehi- cle. Rear Spring Rear spring preload has an effect on comfort, ride height and load compensation.
Page 185 TUNE YOUR RIDE ACTION RESULT Firmer rear suspension Higher rear end Increasing preload More bump absorption capability Heavier steering Softer rear suspension Lower rear end Less bump absorption Decreasing preload capability Lighter steering Better performance and handling in deep snow Refer to the following to determine if preload is correct.
Page 186 50 mm (2 in) preload NOTE: If the specification is unattainable with the original springs, see an authorized Ski-Doo dealer for other available springs. rMotion and rMotion-X Without Quick Adjust To increase spring preload using tool, always turn the left side adjust- ment cam in a clockwise direction, and the right side cam in a coun- terclockwise direction.
Page 187 TUNE YOUR RIDE mmo2012-005-809_a rMOTION AND rMOTION-X WITHOUT QUICK ADJUST - LH SIDE SHOWN 1. Position 1 2. Position 2 3. Position 3 4. Position 4 5. Position 5 6. Adjustment nut _________________...
Page 188 TUNE YOUR RIDE rMotion-X - With Quick Adjust Turn the left side knob to adjust the spring preload. mmo2012-005-817_b rMOTION-X WITH QUICK ADJUST 1. LH side knob to adjust spring preload _________________...
Page 189 TUNE YOUR RIDE 520001798-004_a SC-5M - LH SIDE SHOWN 1. Position 1 2. Position 2 3. Position 3 4. Position 4 5. Position 5 6. Adjustment nut ACTION RESULT Firmer rear suspension Higher rear end Increasing preload More bump absorption capability Heavier steering Softer rear suspension Lower rear end...
Page 190 TUNE YOUR RIDE Center Shock Absorber Center Shock Compression Damping (If Equipped) NOTE: Both low and high speed compression damping are adjusted simultaneously. Low speed compression damping controls how the shock absorber reacts to a low suspension velocity (slow compression strokes, in most cases when riding at lower speeds).
Page 191 TUNE YOUR RIDE mmo2012-005-807_a 1. Center shock compression damping adjustment knob Front Arm Adjustments (rMotion-X) The lower pivot of the front arm can be set to 2 different positions on the rMotion-X suspension. The lower pivot adjustment has an effect on vehicle handling during acceleration.
Page 192 TUNE YOUR RIDE REAR SPRING 3. Set rear spring preload to Minimum. Refer to 4. Firmly hold the spring support and remove the spring support screw and nut. Keep screw and discard nut. CAUTION Spring supports are spring loaded. 520002316-001 5.
Page 193 TUNE YOUR RIDE 6. Repeat for the other side. 7. Remove the cams, pivot 180° and reinstall. 520002316-003 520002316-004 _________________...
Page 194 TUNE YOUR RIDE 520002316-005 8. Reinstall the arm with NEW screws and tighten to specification. 9. Reinstall the spring supports with NEW nuts and tighten to spec- ification. TIGHTENING TORQUE 125 N•m ± 10 N•m Arm pivot screw (92 lbf•ft ± 7 lbf•ft) 24.5 N•m ±...
Page 195 TUNE YOUR RIDE To change the shock lower pivot position, proceed as follows: 1. Lift rear of vehicle and support it off the ground. 2. Remove stopper strap screw to release tension. 3. Remove the shock lower screw and nut. Keep screw and discard nut.
Page 196 TUNE YOUR RIDE 520002316-007_a 1. Lower position (from factory) 2. Shock rod in upper position 6. Reinstall stopper strap screw with a NEW nut. TIGHTENING TORQUE 24.5 N•m ± 3.5 N•m Rear shock lower nut (18 lbf•ft ± 3 lbf•ft) 10 N•m ±...
Page 197 TUNE YOUR RIDE RESULT ON BIG TURNING ACTION AND SMALL BUMPS Increasing Firmer compression Clockwise compression damping damping force Decreasing Counter Softer compression compression Clockwise damping damping force To adjust, turn the adjuster button located on the oil reservoir on shock clockwise to increase compression damping force and coun- terclockwise to decrease compression damping force.
Page 198 TUNE YOUR RIDE rMotion X With Quick Adjust Turn the right side knob to adjust the shock compression speed. mmo2012-005-802_a TYPICAL - rMOTION-X WITH QUICK ADJUST - RH SIDE 1. Knob to adjust low/high speed compression damping Rear Shock Absorber (ACS) Model without the Large Panoramic 7.8"...
Page 199 TUNE YOUR RIDE 219101014-018-029 4. The desired set point appears on the display. To confirm, press the MENU (M) button or wait 5 seconds. 619900974-805 ACS SETTING 3 Model with the Large Panoramic 7.8" Wide LCD Display To adjust, proceed as follows: 1.
Page 200 TUNE YOUR RIDE 3. Turn the knob modify the suspension setting. 4. The desired set point appears on the display. To confirm, press on the knob or wait 5 seconds. 619900974-805 ACS SETTING 3 Coupling Blocks (rMotion and rMotion-X) Coupling blocks adjustment has an effect on vehicle handling during acceleration only.
Page 201: Front Suspension Adjustments
TUNE YOUR RIDE mmo2012-005-806_a COUPLING BLOCK - RIGHT SIDE VIEW (R - RIGHT EMBOSSED ON BLOCK) 1. Position 1 (minimum) 2. Position 2 3. Position 3 4. Position 4 (maximum) 5. Release button Coupling Blocks Setting POSITION More ski lift during acceleration - and best comfort Intermediate setting Intermediate setting...
Page 202 TUNE YOUR RIDE Front spring preload also has an effect on the steering behavior. ACTION RESULT Firmer front suspension Higher front end Increasing preload More precise steering More bump absorption capability Softer front suspension Lower front end Decreasing preload Lighter steering Less bump absorption capability mmo2010-003-027_a...
Page 203 TUNE YOUR RIDE mmo2010-003-019_a TYPICAL - RING TYPE 1. Spring preload adjustment ring 2. Increase preload 3. Decrease preload Front Shock Absorber Front Shock Compression Damping (KYB PRO Series Only) NOTE: Both low and high speed compression damping are adjusted simultaneously.
Page 204: Adjustment Tips According To Vehicle Behavior
TUNE YOUR RIDE mmo2012-005-814_b 1. Compression damping adjuster button RESULT ON BIG TURNING ACTION AND SMALL BUMPS Increasing Firmer compression Clockwise compression damping damping force Decreasing Counter Softer compression compression Clockwise damping damping force Adjustment Tips According to Vehicle Behavior PROBLEM CORRECTIVE MEASURES Check ski alignment.
Page 205 TUNE YOUR RIDE PROBLEM CORRECTIVE MEASURES – Set coupling blocks to a lower position. Steering feels too heavy during acceleration – Reduce rear spring preload. – Lengthen limiter strap. – Set coupling blocks to a higher Too much ski lift position.
Page 206: Vehicle Transportation
VEHICLE TRANSPORTATION Make sure that oil reservoir and fuel tank caps are properly installed. Tilt bed trailers can easily be equipped with a winch mechanism to afford maximum safety in loading. Simple as it may seem, never drive your snowmobile onto a tilt bed trailer or any other kind of trailer or vehicle.
Page 207: Maintenance
MAINTENANCE _________________...
Page 208: Maintenance Schedule
Although an authorized Ski-Doo dealer has an in-depth technical knowledge and tools to service your vehicle, the emission-related warranty is not conditioned on the use of an authorized Ski-Doo dealer or any other establishment with which BRP has a commercial relationship.
Page 209 MAINTENANCE SCHEDULE EVERY YEAR AT PRESEASON OR 3 000 KM (2,000 MI) (WHICHEVER COMES FIRST) Perform pre-ride inspection Check fault codes Charge battery Adjust drive chain Inspect track tension, adjust and align (if necessary) Inspect brake hose, pads and disk Check coolant density Inspect drive belt Inspect and clean drive pulley...
Page 210 MAINTENANCE SCHEDULE EVERY 6 000 KM (4,000 MI) OR AT PRE-SEASON (WHICHEVER COMES FIRST) Change engine oil and filter EVERY 2 YEARS OR 6 000 KM (4,000 MI) (WHICHEVER COMES FIRST) Replace brake fluid Replace chaincase oil EVERY 3 YEARS OR 10 000 KM (6,000 MI) (WHICHEVER COMES FIRST) Replace spark plugs Replace turbo exhaust gasket (on applicable models)
Page 211: Maintenance Procedures
NOTE: When checking level at low temperature it may be slightly lower then the mark. If additional coolant is necessary or if entire system has to be refilled, refer to an authorized Ski-Doo dealer, repair shop or person of your own choosing. _________________...
Page 212: Engine Oil
MAINTENANCE PROCEDURES 520001663-009_a 1. Coolant reservoir 2. COLD line Recommended Engine Coolant XPS RECOMMENDED COOLANT Extended life pre-mixed coolant IF THE RECOMMENDED XPS COOLANT IS NOT AVAILABLE Distilled water and antifreeze solution (50% distilled water, 50% antifreeze) NOTICE Always use ethylene-glycol antifreeze containing cor- rosion inhibitors specifically for internal combustion aluminum engines.
Page 213 MAINTENANCE PROCEDURES Place vehicle on a level surface and proceed as follows to check oil level: 1. Start engine and let it reach its normal operating temperature. En- gine is at normal temperature when rear radiator gets warm, indi- cating that the thermostat is open. 2.
Page 214 MAINTENANCE PROCEDURES WARNING Wipe off any oil spills. Oil is highly flammable when heated. Engine Oil Replacement CAUTION The engine oil can be very hot. Wait until engine oil is warm. NOTICE Engine oil and oil filter must be replaced at the same time.
Page 215 MAINTENANCE PROCEDURES Pivot the access cover to clear the bottom pan opening. 520001899-008_a 1. Drain plugs access cover 520001899-009_a PIVOT THE ACCESS COVER 1. Retaining screws 7. Clean drain plug area. _________________...
Page 216 MAINTENANCE PROCEDURES 8. Place a drain pan under the bottom pan opening. 9. Remove engine drain plugs in the following order. Main drain plug. Secondary drain plug. mmr2011-070-053_a UNDERNEATH THE ENGINE 1. Main drain plug 2. Secondary drain plug 10. Allow oil to drain completely. 11.
Page 217 MAINTENANCE PROCEDURES mmr2011-070-004_a 1. Sealing washer 2. Oil drain plug 12. Install drain plugs and tighten to specification. TIGHTENING TORQUE 20 N•m ± 2 N•m Drain plugs (15 lbf•ft ± 1.5 lbf•ft) OIL FILTER 13. Install a new , see procedure in this subsection. 14.
Page 218: Engine Oil Filter
MAINTENANCE PROCEDURES Engine Oil Filter Engine Oil Filter Replacement Oil Filter Removal 1. Remove the RH side panel. 2. Clean oil filter area. 3. Remove: – Oil filter cover screws – Oil filter cover with O-ring – Oil filter. mmr2011-070-007_a 1.
Page 219 MAINTENANCE PROCEDURES mmr2011-070-008_a 1. Oil inlet orifice from the oil pressure pump 2. Oil outlet orifice to the engine lubrication system 3. Oil filter receptacle 2. Install a NEW O-ring on oil filter cover. 3. Install the new filter into the cover. 4.
Page 220: Exhaust System
Spark Plugs Spark plugs inspection or replacement may be performed by an au- thorized Ski-Doo dealer, repair shop, or person of your own choosing. Spark plugs inspection or replacement requires an in-depth technical knowledge. Though not required, it is recommended that an autho- rized Ski-Doo dealer performs spark plugs inspection or replacement.
Page 221 MAINTENANCE PROCEDURES WARNING Use only DOT 4 brake fluid from a sealed container. To avoid serious damage to the braking system, do not use fluids other than the recommended one, nor mix different fluids for top- ping up. NOTICE Brake fluid can damage painted and plastic parts. Handle with care.
Page 222: Chaincase Oil
MAINTENANCE PROCEDURES mmo2008-008-018_a TYPICAL 1. Minimum 2. Maximum 3. Operating range CAUTION Avoid getting brake fluid on skin or eyes - it may cause severe burns. In case of contact skin, wash thoroughly. In case of contact with the eyes, immediately rinse with plenty of water for at least 10 minutes and then consult a doctor imme- diately.
Page 223 MAINTENANCE PROCEDURES NOTICE The chaincase of this snowmobile has been devel- oped and validated using the XPS™ Synthetic chaincase oil. BRP strongly recommends the use of its XPS Synthetic chain- case oil at all times. Damages caused by oil which is not suitable for the chaincase will not be covered by the BRP limited war- ranty.
Page 224 MAINTENANCE PROCEDURES TIGHTENING TORQUE 6 N•m ± 1 N•m Check plug (53 lbf•in ± 9 lbf•in) CHAINCASE FILLING PROCEDURE If level is insufficient, See Chaincase Filling Procedure Remove the check plug. 520001663-011_a CHECK PLUG Remove the filler cap. _________________...
Page 225: Drive Chain
MAINTENANCE PROCEDURES 520001899-006_a TYPICAL - TOP OF CHAINCASE 1. Filler cap Pour recommended oil in the filler hole until oil comes out by the check plug hole. Reinstall check plug and tighten to the specified torque. TIGHTENING TORQUE 6 N•m ± 1 N•m Check plug (53 lbf•in ±...
Page 226: Drive Belt
RPM with frozen track, fast starts without warm-up period, burred or rusty sheave, oil on belt or distorted spare belt. Contact an authorized Ski-Doo dealer. Drive Belt Replacement Drive Belt Removal 1. Remove tether cord cap from engine cut-off switch.
Page 227 MAINTENANCE PROCEDURES 520001899-212_a TYPICAL - PULLEY EXPANDER INSTALLED ON ADJUSTER HUB 4. Open the driven pulley by screwing the tool in. 5. Remove the drive belt by slipping it over the top of the driven pul- ley, then over the drive pulley. Drive Belt Installation DRIVE BELT RE- 1.
Page 228 MAINTENANCE PROCEDURES mmo2011-002-006_a 1. To be pointed in the direction of rotation 3. Unscrew and remove the driven pulley expander from the pulley. 4. Rotate the driven pulley several times to properly set the belt be- tween the sheaves. 5. If a new belt was installed, an adjustment will be required for the DRIVE BELT HEIGHT ADJUSTMENT proper belt height.
Page 229 MAINTENANCE PROCEDURES mmo2011-003-010_a 1. Adjuster hub 2. Clamping bolt 4. Using the suspension adjustment tool provided, turn the ring 1/4 turn at a time then rotate the driven pulley to properly set the drive belt between the pulley sheaves. mmo2011-003-011_a 1.
Page 230 MAINTENANCE PROCEDURES NOTE: The adjustment ring has left hand treads. Repeat step 4 until the lowest portion of the cogs on the external sur- face of drive belt is even with the driven pulley edge. mmo2012-006-905_a TYPICAL - PRELIMINARY SETTING 1.
Page 231 MAINTENANCE PROCEDURES mmo2012-004-903_a TYPICAL 1. Clamping bolt 6. Install drive belt guard. 7. Install side panel. NOTE: These settings are correct as a preliminary adjustment for most models. In some cases, when starting the engine, the vehicle could creep, indicating that the drive belt is too tight. If the vehicle creeps, lower the drive belt height from the preliminary setting.
Page 232: Track
If worn or cut, or if track fibers are exposed, or if missing or defective inserts or guides are noted; contact an authorized Ski-Doo dealer. Snowmobiles Equipped with Traction Enhancing Products...
Page 233 MAINTENANCE PROCEDURES WARNING Riding with a damaged track or studs could lead to a loss of control. For complete information on traction enhancing products, refer to TRACTION ENHANCING PRODUCTS SAFETY INFORMATION the beginning of this Operator's Guide. Track Tension and Alignment NOTE: Track tension and alignment are interrelated.
Page 234 MAINTENANCE PROCEDURES 414348200 5. Set deflection between 30 mm and 35 mm (1-3/16 in and 1-3/8 in) using bottom O-ring. mmr2009-133-003_b DEFLECTION SETTING 1. Bottom O-ring set to specification 6. Place upper O-ring to 0 kgf (0 lbf). 7. Position the tensiometer on track, halfway between front and rear idler wheels.
Page 235 MAINTENANCE PROCEDURES mmr2009-133-002_a 1. Deflection O-ring aligned with slider shoe 9. Read load recorded by the upper O-ring on the tensiometer. mmr2009-133-003_a LOAD READING 1. Upper O-ring 10. Load reading must be as per the following table. TRACK ADJUSTMENT SPECIFICATION Track deflection setting 3.2 cm (1.26 in) Track load reading...
Page 236 520001663-027_a Step 1: Remove cap Step 2: Loosen the axle screw or nut Step 3: Tighten or loosen adjustment screws 5. If correct tension is unattainable, contact an authorized Ski-Doo dealer. 6. Retighten the rear axle fasteners to specification. _________________...
Page 237 MAINTENANCE PROCEDURES TIGHTENING TORQUE Rear idler wheel retaining 48 N•m ± 6 N•m screws (35 lbf•ft ± 4 lbf•ft) 7. Check track alignment as described below. Track Alignment WARNING Before checking track alignment, ensure that the track is free of all particles which could be thrown out while track is ro- tating.
Page 238 MAINTENANCE PROCEDURES A01F05A 1. Guides 2. Slider shoes 3. Equal distance 4. To correct track alignment: Stop engine. Remove tether cord cap from engine cut-off switch. WARNING Remove tether cord cap from engine cut-off switch be- fore performing any maintenance or adjustment, unless otherwise specified.
Page 239: Suspension
MAINTENANCE PROCEDURES A01F0BA 1. Guides 2. Slider shoes 3. Tighten on this side 5. Tighten the rear axle nut. WARNING Properly tighten wheel retaining bolt, otherwise wheel may come off and cause track to “lock”. 6. Restart engine and rotate track slowly to recheck alignment. 7.
Page 240 MAINTENANCE PROCEDURES Suspension Stopper Strap Condition Inspect stopper straps for wear and cracks, bolt and nut for tightness. If loose inspect holes for deformation. Replace as required. Tighten nut to specification. TIGHTENING TORQUE 10 N•m ± 1 N•m (89 lbf•in ± 9 lbf•in) Stopper strap nut Suspension Lubrication Lubricate the following suspension pivots at grease fittings.
Page 241: Skis
Steering and Front Suspension Condition Visually inspect steering and front suspension for tightness of com- ponents (steering arms, control arms and links, tie rods, ball joints, ski bolts, ski legs, etc.). If necessary, contact an authorized Ski-Doo dealer. Skis Wear and Condition of Skis and Runners Check the condition of the skis and ski runner carbides.
Page 242 MAINTENANCE PROCEDURES Fuses Location 520002346-002 TYPICAL 1. Fuse block Unlock fuse block from its cover. Enduro models AMPERAGE FUSE IDENTIFICATION RATING Clock/Start/Relays Headlamps 20 A 10 A Taillight/Brake/PAC ECM/RFID/O2 10 A Sensor/CAPS 10 A Fuel Pump/Starter 15 A Accessory 15 A _________________...
Page 243 MAINTENANCE PROCEDURES AMPERAGE FUSE IDENTIFICATION RATING 15 A Cluster 15 A 30 A RELAY IDENTIFICATION Main Forward Reverse Accessory Lighting Sport, Adrenaline, X and X-RS models AMPERAGE FUSE IDENTIFICATION RATING Start/Relays Accessory 15 A 10 A Taillight/Brake/PAC ECM/RFID/O2 10 A Sensor/CAPS Fuel Pump/Engine 10 A...
Page 244 A15E0KA 1. Fuse 2. Check if melted WARNING Do not use a higher rated fuse. WARNING If fuse has burnt out, source of malfunction should be deter- mined and corrected before restarting. See an authorized Ski-Doo dealer for servicing. _________________...
Page 245: Headlights
MAINTENANCE PROCEDURES Headlights Headlights Bulb Replacement 1. Open the storage compartment. 520001663-006_a 2. Remove the gauge support retaining screws. 619900974-008 _________________...
Page 246 MAINTENANCE PROCEDURES 3. Lift the front of the gauge support, then slide it forward to remove 619900974-009 4. Set gauge support aside. 5. Remove the storage compartment. _________________...
Page 247 MAINTENANCE PROCEDURES 520001663-017_a 6. Disconnect MAPTS and bulb connector. mmr2017-036-006 7. Unlock bulb by turning it counterclockwise. 8. Pull bulb out. NOTE: Ensure bulb seal stays in place. _________________...
Page 248 MAINTENANCE PROCEDURES mmr2017-036-008 1. Bulb 2. Bulb seal Install a new bulb using the reverse of the removal procedure. NOTICE Never touch glass portion of an halogen bulb with bare fingers, it shortens its operating life. If glass is touched, clean it with isopropyl alcohol which will not leave a film on the bulb.
Page 249: Removing Battery
MAINTENANCE PROCEDURES mmr2017-036-005 Removing Battery WARNING Battery BLACK ( – ) cable must always be disconnected first and connected last. Never charge or boost battery while in- stalled on vehicle. 1. Remove seat. 2. Remove battery cover. _________________...
Page 250 MAINTENANCE PROCEDURES 520001896-020_a TYPICAL 3. Disconnect negative before positive terminal. mmr2017-032-002 4. Remove battery hold down bracket. _________________...
Page 251: Installing Battery
MAINTENANCE PROCEDURES mmr2017-032-003 5. Remove battery. mmr2017-032-004 Installing Battery The installation is the reverse of the removal procedure. However, pay attention to the following details. _________________...
Page 252 MAINTENANCE PROCEDURES TIGHTENING TORQUE Battery terminals (positive 10 N•m ± 2 N•m and negative) (89 lbf•in ± 18 lbf•in) 5 N•m ± 0.5 N•m Battery hold down bracket (44 lbf•in ± 4 lbf•in) 7 N•m ± 1 N•m Battery cover retaining screws (62 lbf•in ±...
Page 253: Vehicle Care
VEHICLE CARE Post-Operation Care Remove snow and ice from rear suspension, track, front suspension, steering mechanism and skis. WARNING Make sure D.E.S.S. key is removed from D.E.S.S. post before standing in front the vehicle, getting close to the track or rear suspension components.
Page 254: Storage
STORAGE During summer, or when a snowmobile is not in use for more than three months, proper storage is necessary. STORAGE Clean the vehicle Add fuel stabilizer to fuel following the product manufacturer recommendations. Run the engine after adding the product to the fuel Lubricate engine Lubricate brake lever pivot...
Page 255: Technical Information
TECHNICAL INFORMATION _________________...
Page 256: Vehicle Identification
VEHICLE IDENTIFICATION Vehicle Description Decal Vehicle description decal is located on right hand side of tunnel. 520002104-001 TYPICAL 1. Vehicle description decal Date BOMBARDIER RECREATIONAL PRODUCTS Inc. VIN. / NIV. Description Type: SNO/MNG ASSEMBLED IN CANADA / ASSEMBLÉ AU CANADA EN-516009003-DEC TYPICAL 520002459...
Page 257: Identification Numbers
These numbers are required by the authorized Ski-Doo dealer to complete warranty claims properly. We strongly recommend that you take note of all the identification numbers on your snowmobile and supply them to your insurance company.
Page 258 VEHICLE IDENTIFICATION Engine Identification Number Location mmo2014-004-007_a 1. Engine identification number _________________...
Page 259: Noise Emission And Vibration Values (All Countries Except Canada/United States)
NOISE EMISSION AND VIBRATION VALUES (ALL COUNTRIES EXCEPT CANADA/UNITED STATES) 900ACE MODEL 600 ACE 900 ACE Turbo NOISE EMISSION AND VIBRATION VALUES 90,4 dB @ 91,2 dB @ 98,4 dB @ Sound power 3625 RPM 3625 RPM 3625 RPM Noise level (L (Uncertainty (Uncertainty...
Page 260: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY DoC_Ski-Doo_MY21 _________________...
Page 261: Eac Declaration Of Conformity
EAC DECLARATION OF CONFORMITY Left blank for Eurasian Conformity mark where applicable _________________...
Page 262: Epa Certified Engines
Dealer's Responsibility When performing service on a certified Ski-Doo snowmobiles that carry an emissions control information label, adjustments must be kept within published factory specifications.
Page 263 EPA CERTIFIED ENGINES The responsibilities listed above are general and in no way a com- plete listing of the rules and regulations pertaining to the EPA requirements on exhaust emissions for snowmobile products. For more detailed information on this subject, you may contact the following locations: MAIL: U.S.
Page 264: Radio Frequency Digitally Encoded Security System (Rf D.e.s.s. Key)
RADIO FREQUENCY DIGITALLY ENCODED SECURITY SYSTEM (RF D.E.S.S. KEY) This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device.
Page 265: Specifications
SPECIFICATIONS Engine ENGINE 600 ACE Rotax 600, liquid cooled, 4-stroke, Engine type D.O.H.C., dry sump. Number of cylinder Bore 74 mm (2.91 in) Stroke 69.7 mm (2.74 in) Displacement 600 cm³ (36.6 in³) Maximum power engine speed 7250 RPM ENGINE 900 ACE Rotax 903, liquid cooled, 4-stroke,...
Page 266 SPECIFICATIONS ENGINE 900 ACE TURBO 69.7 mm (2.74 in) Stroke Displacement 899 cm³ (54.9 in³) Maximum power engine speed 7750 RPM FUEL SYSTEM Multi point EFI, Fuel delivery 46 mm heated throttle body Idle speed (not adjustable) 1200 ± 200 RPM ELECTRICAL SYSTEM 50 A @ 14.5 V Total system output...
Page 267 SPECIFICATIONS LUBRICATION SYSTEM RECOMMENDED ENGINE OIL in the MAINTENANCE Recommended oil PROCEDURES section of this guide Engine oil Oil change, 2.1 L 600 ACE (2.22 qt (U.S. liq.)) Quantity 900 ACE Oil change with 900 ACE filter: 3.5 L Turbo (3.7 qt (U.S.
Page 268: Vehicles
SPECIFICATIONS Vehicles COOLING SYSTEM RECOMMENDED ENGINE COOLANT in the Coolant Type MAINTENANCE PROCEDURES section of this guide FUEL SYSTEM Fuel pump In-tank electrical Regular unleaded FUEL Type Refer to REQUIREMENTS 600 ACE 900 ACE 87 Pump Posted Octane AKI (R+M)/2) rating Premium Fuel...
Page 269 SPECIFICATIONS ELECTRICAL SYSTEM Battery 12 V, 18 A•h 2 x 60/55 W Headlamp (H-13) 2.6 W / 139m Taillight and stoplight W LED FUSES Refer to Fuses MAINTENANCE DRIVE SYSTEM Synthetic Type chaincase oil Chaincase 500 ml Capacity (16.9 U.S. oz) 600 ACE 21/51 Chain drive ratio...
Page 270 SPECIFICATIONS DRIVE SYSTEM Width 38 cm (15 in) Length 348.7 cm (137 in) Track 31.8 mm (1.25 in) Profile height 34 mm (1.35 in) 38 mm (1.5 in) Deflection 3.2 cm (1.26 in) Track adjustment 6.0 kgf to 8.5 kgf Force (13 lbf to 19 lbf) BRAKE SYSTEM...
Page 271 SPECIFICATIONS FRONT SUSPENSION Renegade Adrenaline RAS 3 Renegade Enduro Suspension type Renegade Sport Renegade X-RS RAS X Renegade X Renegade Adrenaline 220 mm (8.7 in) Renegade Enduro Suspension Renegade Sport maximum travel Renegade X 243 mm (9.6 in) 265 mm (10.4 in) Renegade X-RS Renegade X-RS KYB Pro 36 EA...
Page 272 SPECIFICATIONS REAR SUSPENSION Renegade Adrenaline Renegade Enduro Renegade HPG Plus Center Renegade KYB PRO 40 EA X_RS Renegade Motion control Sport Shock absorber type Renegade Adrenaline Renegade Sport ACS (Air Renegade Controlled Rear Enduro Suspension) Renegade KYB PRO 36 EA Renegade KYB PRO 40 EA X-RS...
Page 273 SPECIFICATIONS WEIGHT AND DIMENSIONS Renegade Adrenaline 227 kg (499 lb) 900 ACE Renegade Adrenaline 239 kg (527 lb) 900 ACE Turbo Renegade Enduro 241 kg (529 lb) Mass (dry) 900 ACE Renegade Enduro 253 kg (558 lb) 900 ACE Turbo 213 kg (469 lb) Renegade Sport Renegade X...
Page 274 SPECIFICATIONS This page is intentionally blank _________________...
Page 275: Trouble-Shooting
TROUBLE- SHOOTING _________________...
Page 276: Troubleshooting Guidelines
– Install a tether cord cap for which this snowmobile was pro- grammed. 3. ECM does not recognize the D.E.S.S. key. – Refer to an authorized Ski-Doo dealer. ENGINE LACKS ACCELERATION OR POWER 1. Engine warm-up in progress. – Drive vehicle at low speeds for a few minutes.
Page 277 Ski-Doo dealer for proper alignment and tension adjustments. 7. Fuel pressure too low. – Seek service from an authorized Ski-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or re- placement. Please refer to the US EPA EMISSION-RELATED WARRANTY contained herein for information about warranty claims.
Page 278 TROUBLESHOOTING GUIDELINES ENGINE BACKFIRES (cont’d) 4. Fuel pressure too low. – Seek service from an authorized Ski-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or re- placement. Please refer to the US EPA EMISSION-RELATED WARRANTY contained herein for information about warranty claims.
Page 279: Monitoring System
MONITORING SYSTEM Pilot Lamps, Messages and Beeper Codes Gauge pilot lamp(s) will inform you if an anomaly occurs or to inform you of a particular condition. 219100975-004 TYPICAL — PILOT LAMPS Pilot lamp can flash alone or in combination with another lamp. On the multifunction analog/digital gauge, the center display is used as a complement of the pilot lamps to give you a brief description if an anomaly occurs or to inform you of a particular condition.
Page 280 Check coolant level, refer HIGH ENGINE MAINTENANCE TEMPERATURE coolant level is correct and overheating persists, contact authorized 1 Long Ski-Doo dealer. Do not beep run the engine if condition repeating persists. Reduce speed stop engine. Let engine cool down restart.
Page 281 Do not OVERHEAT run the engine if condition persists. Indicate a low or high battery voltage condition. — BATT VOLT See an authorized Ski-Doo dealer as soon as possible. Engine fault, 1 Long authorized Ski-Doo dealer, CHECK beep repair shop or person of...
Page 282 MONITORING SYSTEM PILOT MESSAGE LAMP BEEPER DESCRIPTION DISPLAY 2 short Good key, vehicle ready to — beeps operate. Unable to read key (bad connection). Make sure — WRONG KEY clean DESS correctly snapped on post. Invalid key or key not programmed.
Page 283 WARRANTY _____...
Page 284: Brp Limited Warranty Usa And Canada: 2021 Ski-Doo
WARRANTY Bombardier Recreational Products Inc. (“BRP”)* warrants its 2021 Ski-Doo snowmobiles sold by authorized BRP dealers (as defined be- low) in the United States of America (“USA”) and in Canada from de- fects in material or workmanship for the period and under the con- ditions described below.
Page 285 3) EXCLUSIONS – ARE NOT WARRANTED The following are not warranted under any circumstances: – Normal wear and tear; – Routine maintenance items, tune ups, adjustments; – Damage caused by failure to provide proper maintenance and/or storage, as described in the Operator's Guide; –...
Page 286 This warranty coverage is available only if each of the following con- ditions has been fulfilled: – The 2021 Ski-Doo snowmobile must be purchased as new and unused by its first owner from a BRP dealer authorized to dis- tribute Ski-Doo snowmobiles in the country in which the sale occurred (“BRP dealer”);...
Page 287 BRP’s obligations under this warranty are limited to, at its sole discre- tion, repairing parts found defective under normal use, maintenance and service, or replacing such parts with new genuine Ski-Doo parts without charge for parts and labor , at any authorized BRP dealer during the warranty coverage period under the conditions described herein.
Page 288 9) CONSUMER ASSISTANCE In the event of a controversy or a dispute in connection with this lim- ited warranty, BRP suggests that you try to resolve the issue at the dealership level. We recommend discussing the issue with the au- thorized dealer's service manager or owner.
Page 289: Us Epa Emission-Related Warranty
BRP. For all emission-related warranty claims, BRP is limiting the diagnosis and repair of emission-related parts to the authorized Ski-Doo deal- ers, unless for emergency repairs as required by item 2 of the follow- ing list.
Page 290 Emission-Related Warranty Period The emission-related warranty is valid for the following period whichever comes first: HOURS MONTHS KILOMETERS Exhaust emission-related 4000 components Evaporative emission-related components Components Covered The emission-related warranty covers all components whose failure would increase an engine’s emissions of any regulated pollutant, in- cluding the following listed components: 1.
Page 291 – Control solenoids* – Electronic controls* – Vacuum control diaphragms* – Control cables* – Control linkages* – Purge valves – Vapor hoses – Liquid/vapor separator – Carbon canister – Canister mounting brackets – Carburetor purge port connector 4. Emission-related components also include any other part whose only purpose is to reduce emissions or whose failure will increase emissions without significantly degrading engine/equipment per- formance.
Page 292: Ski-Doo
1) SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. (“BRP”)* warrants its 2021 Ski-Doo snowmobiles sold by distributors or dealers authorized by BRP to distribute Ski-Doo snowmobiles ("Ski-Doo Distribu- tor/Dealer") in member states of the European Economic Area (which is comprised of the member states of the European Union plus the United Kingdom, Norway, Iceland and Liechtenstein) ("EEA"), in member states of the Commonwealth of the Indepen-...
Page 293 ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY FROM COUNTRY TO COUNTRY. Neither the Ski-Doo Distributor/Dealer nor any other person has been authorized to make any affirmation, representation or warranty regarding the product, other than those contained in this limited warranty, and if made, shall not be enforceable against BRP.
Page 294 This warranty coverage is available only if each of the following con- ditions has been fulfilled: – The 2021 Ski-Doo snowmobile must be purchased as new and unused by its first owner from a Ski-Doo Distributor/Dealer au- thorized to distribute Ski-Doo products in the country in which the sale occurred;...
Page 295 WARRANTY COVERAGE The customer must cease using the snowmobile upon the appear- ance of an anomaly. The customer must notify a servicing Ski-Doo Distributor/Dealer within two (2) months of the appearance of a defect, and provide it with reasonable access to the product and reasonable opportunity to repair it.
Page 296 BRP or an authorized Ski-Doo Distribu- tor/Dealer receives a proof that the former owner agreed to the transfer of ownership, in addition to the co-ordinates of the new owner.
Page 297 ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be responsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished...
Page 298: Brp International Limited Warranty: 2021 Ski-Doo
1) SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. (“BRP”)* warrants its 2021 Ski-Doo snowmobiles sold by distributors or dealers au- thorized by BRP to distribute SKI-Doo snowmobiles ("Ski-Doo Distributor/Dealer") outside of the fifty United States, Canada, members of the European Economic Area (which is comprised of the member states of the European Union plus the United Kingdom, Norway, Iceland and Liechtenstein) (“EEA”), members states of the...
Page 299 Neither the Ski-Doo Distributor/Dealer nor any other person has been authorized to make any affirmation, representation or warranty regarding the product, other than those contained in this limited warranty, and if made, shall not be enforceable against BRP. BRP reserves the right to modify this warranty at any time, being un- derstood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
Page 300 This warranty coverage is available only if each of the following con- ditions has been fulfilled: – The 2021 Ski-Doo snowmobile must be purchased as new and unused by its first owner from a Ski-Doo Distributor/Dealer autho- rized to distribute Ski-Doo snowmobiles in the country in which the sale occurred;...
Page 301 – The product must have undergone proper registration by an au- thorized Ski-Doo Distributor/Dealer; – The 2021 Ski-Doo snowmobile must be purchased in the country or union of countries in which the purchaser resides. – Routine maintenance outlined in the Operator’s Guide must be timely performed in order to maintain warranty coverage.
Page 302 BRP or an authorized Ski-Doo Distribu- tor/Dealer receives a proof that the former owner agreed to the transfer of ownership, in addition to the co-ordinates of the new owner.
Page 303: Maintenance Records
MAINTENANCE RECORDS Send photocopy of maintenance record to BRP if needed. PREDELIVERY Serial Signature/Print: number: Mileage / Hours: Date: Dealer Notes: Refer to vehicle Pre-Delivery Bulletin for detailed installation procedures FIRST INSPECTION Mileage / Signature/Print: Hours: Date: Dealer Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide _________________...
Page 304 SERVICE Mileage / Signature/Print: Hours: Date: Dealer Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / Signature/Print: Hours: Date: Dealer Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide _________________...
Page 305 SERVICE Mileage / Signature/Print: Hours: Date: Dealer Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / Signature/Print: Hours: Date: Dealer Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide _________________...
Page 306 SERVICE Mileage / Signature/Print: Hours: Date: Dealer Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / Signature/Print: Hours: Date: Dealer Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide _________________...
Page 307 SERVICE Mileage / Signature/Print: Hours: Date: Dealer Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / Signature/Print: Hours: Date: Dealer Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide _________________...
Page 308 This page is intentionally blank _________________...
Page 309: Customer Information
CUSTOMER INFORMATION _____...
Page 310: Privacy Information
PRIVACY INFORMATION BRP wishes to inform you that your coordinates will be used for safety and warranty related purposes. Furthermore, BRP and its affiliates may use its customer list to distribute marketing and pro- motional information about BRP and related products. To exercise your right to consult or correct your data, or to be re- moved from the addressee-list for direct marketing, please contact BRP.
Page 311: Contact Us
CONTACT US www.brp.com Asia Room 4609, Tower 2, Grand Gateway 3 Hong Qiao Road Shanghai, China 200020 21F Shinagawa East One Tower 2-16-1 Konan, Minatoku-ku, Tokyo 108-0075 Japan Europe Skaldenstraat 125 B-9042 Gent Belgium Itterpark 11 D-40724 Hilden Germany ARTEPARC Bâtiment B Route de la côte d'Azur, Le Canet 13590 Meyreuil France...
Page 312: North America
CONTACT US North America 565 de la Montagne Street Valcourt (Québec) J0E 2L0 Canada Sa De Cv, Av. Ferrocarril 202 Parque Ind. Querétaro, Lote2-B 76220 Santa Rosa Jáuregui, Qro., Mexico Sturtevant, Wisconsin, U.S.A. 10101 Science Drive Sturtevant, Wisconsin 53177 U.S.A. Oceania 6 Lord Street Lakes Business Park...
Page 313: Change Of Address/Ownership
BRP. STOLEN UNITS: If your personal Snowmobile is stolen, you should notify BRP or an authorized Ski-Doo dealer. We will ask you to pro- vide your name, address, phone number, the vehicle identification number and the date it was stolen.
Page 314 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank _________________...
Page 315 CHANGE OF ADDRESS/OWNERSHIP _________________...
Page 316 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank _________________...
Page 317 CHANGE OF ADDRESS/OWNERSHIP _________________...
Page 318 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank _________________...
Page 319 CHANGE OF ADDRESS/OWNERSHIP NOTES _________________...
Page 320 CHANGE OF ADDRESS/OWNERSHIP NOTES _________________...
Page 321 CHANGE OF ADDRESS/OWNERSHIP NOTES _________________...
Page 322 CHANGE OF ADDRESS/OWNERSHIP NOTES _________________...
Page 323 520 002 409 OPERATOR’S GUIDE REV GEN4 TRAIL / CROSSOVER ACE SERIES / ENGLISH GUIDE DU CONDUCTEUR REV GEN4 SÉRIES TRAIL / CROSSOVER ACE / ANGLAIS FAIT AU / MADE IN CANADA ®TM AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC.

This manual is also suitable for:

Rev gen4 2021

Ski-Doo REV GEN4 Operator's Manual

Foreword

Safety Information

General Precautions

Special Safety Messages

ACTIVE TECHNOLOGIES (Itc)

Riding the Vehicle

Traction Enhancing Products

Moving Loads and Doing Work

Important On-Product Labels

IMPORTANT ON-PRODUCT LABELS (Cont'D)

Reporting Safety Defects

Vehicle Information

Controls, Instruments and Equipment

4.5" Digital Display

7.2" Digital Display

Large Panoramic 7.8" Wide Lcd Display

Fuel and Oil

Break-In Period

Operating Modes

Basic Procedures

Riding Conditions and Your Snowmobile

Special Operation

Tune Your Ride

Vehicle Transportation

Maintenance

Maintenance Schedule

Maintenance Procedures

Vehicle Care

Storage

Technical Information

Vehicle Identification

Noise Emission and Vibration Values (All Countries Except Canada/United States)

Ec Declaration of Conformity

Eac Declaration of Conformity

Epa Certified Engines

Radio Frequency Digitally Encoded Security System (Rf D.e.s.s. Key)

(Rfd.e.s.s.key)

Specifications

Trouble-Shooting

Troubleshooting Guidelines

Monitoring System

Brp Limited Warranty Usa and Canada: 2021 Ski-Doo

Snowmobiles

Us Epa Emission-Related Warranty

States (Cis) Areas and Turkey

And the Commonwealth of

Snowmobiles

Ski-Doo

Brp International Limited Warranty: 2021 Ski-Doo

Snowmobiles

Maintenance Records

Customer Information

Privacy Information

Contact Us

Change of Address/Ownership

Quick Links

Need help?

Questions and answers

Related Manuals for Ski-Doo REV GEN4

Summary of Contents for Ski-Doo REV GEN4