Advertisement
Quick Links
H-9234, H-9246
20 x 20' EVENT TENT
TOOL NEEDED
Sledge Hammer
(for H-9234)
(recommended)
Pole
6'8" Leg (LG) – Black x 8
9'4" Eave (EV) – White x 8
10'6" Full Rafter (FR) – Green x 4
14'4" Hip Rafter (HR) – Red x 4
Base Plate x 8
IMPORTANT! Please read carefully.
• Keep away from all flame and heat sources.
• Do not cook underneath or near canopy.
• Do not store or use flammable liquids underneath or
near canopy.
• Do not ignite or store fireworks underneath or near
canopy.
• Do not use bleach to clean cover.
• Do not dry clean cover.
PAGE 1 OF 8
Drop Cloth
Corner x 4
Frame Pin x 48
1-800-295-5510
uline.com
Two Person Assembly
Recommended
PARTS
8-Way Crown x 1
Canopy Top x 1
SAFETY
• Do not wash cover in washing machine or dry in
dryer. Hand wash with mild soap and water only.
• Do not allow rain water, snow or ice to accumulate
on top of cover.
• Do not hang or suspend anything from the frame,
grommets or truss system of the unit.
• Remove rain water, snow and ice from canopy
cover.
NOTE: This is a temporary structure and is
not recommended for use as a permanent
structure.
4-Way Side Tee x 4
Steel Stake x 8
(for H-9234)
2" Ratchet
Strap x 8
Barrel x 8
(for H-9246)
0221 IH-9234
Advertisement
Related Manuals for U-Line H-9234
Summary of Contents for U-Line H-9234
- Page 1 H-9234, H-9246 1-800-295-5510 uline.com 20 x 20' EVENT TENT TOOL NEEDED Two Person Assembly Sledge Hammer Drop Cloth Recommended (for H-9234) (recommended) PARTS Pole Corner x 4 8-Way Crown x 1 4-Way Side Tee x 4 2" Ratchet 6'8" Leg (LG) – Black x 8 Strap x 8 9'4"...
- Page 2 ASSEMBLY IMPORTANT! Before setting up tent, contact b. Place a pin in every other alignment hole. This Diggers Hotline (8-1-1) or a local authority to pin prevents the rafter from moving too far onto verify that it is safe to set up tent in desired crown.
- Page 3 ASSEMBLY CONTINUED b. Align placement hole in the crown with hole in 5. Beginning at a corner fitting, attach eave poles (EV) rafter and insert pin. (See Figure 6) to corner fittings and 4-way side tee fittings, working clockwise around the assembly. (See Figures 9-10) Figure 6 Figure 9 Placement...
- Page 4 ASSEMBLY CONTINUED Unroll the tent top. (See Figures 12-13) 10. Loosely fasten the alligator straps attached to canopy top at each side of the corners around EV NOTE: It is recommended to place tent top on a tubing to secure tent top. (See Figure 16) drop cloth to protect from dirt and abrasions.
- Page 5 CAUTION! Yanking on straps will cause undue wear and tear as well as wrinkling of tent top fabric. IF USING STAKES (H-9234) Place stakes 5' out from each leg. Drive stakes into the ground until 6" or less of the stake shows.
- Page 6 ASSEMBLY CONTINUED IF USING BARRELS (H-9246) NOTE: Attach strap at bottom of barrel before filling barrel with water. (See Figure 26) 1. Turn the barrel upside down to connect the mounting plate. (See Figure 24) Figure 26 Figure 24 Loop Strap Barrel 3.
- Page 7 ASSEMBLY CONTINUED NOTE: Keep ratchet buckle handle facing up at all times. 7. After barrel is full, tighten ratchet straps by first pulling all slack through ratchet reel, holding strap with one hand and cranking ratchet handle with the other. 8.
- Page 8 TAKING DOWN TENT CONTINUED 5. Remove remaining legs. (See Figure 36) Bagging: a. Place the folded tent top in an upright vertical Figure 36 position. b. Pull tent bag over the upright tent top. c. Turn the tent top and bag over. 10.
Need help?
Do you have a question about the H-9234 and is the answer not in the manual?
Questions and answers