GE LEDa-G90-8 Quick Start Manual

Ultrabright LED 8PC G90 Pathway marker light set
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
READ & FOLLOW ALL SAFETY INSTRUCTIONS
1. This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock,
it should not be played with or placed where small children can reach it.
2. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit
Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper
installation.
3. Do not use this product for other than its intended use.
4. This seasonal use product is not intended for permanent use or installation.
5. Unplug when leaving the house, when retiring for the night, or if left unattended.
6. Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
7. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
8. Do not hang ornaments or other objects from cord, wire, or light string.
9. Do not place lighting string on carpeting, drapes, furniture, or allow it to contact vinyl siding
while the power is on.
10. Do not perform any maintenance or troubleshoot for bad or broken lamps while the power is on.
11. Do not close doors or windows on the product or extension cords as this may damage the
wire insulation.
12. Do not cover the product with cloth, paper or any material not part of the product when in use.
13. Do not let lamps rest on the supply cord or on any wire.
14. Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
1. Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed
wire insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
2. Before storing the product, carefully remove the product from wherever it is placed, including trees,
branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
3. When not in use, store neatly in a cool, dry location protected from sunlight.
4. When the product is used on a live tree, the tree should be well maintained and fresh. Do not place on live
trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
5. lf the product is placed on a tree, the tree should be well secured and stable.
CAUTION:
To reduce the risk of fire electric shock: a) Do not install on trees having needles, leaves or branch coverings
of metal or materials that look like metal, and b)Do not mount or support strings in a manner that can cut or
damage wire insulation.
-SEE OTHER SIDE-
MODEL NO.:
NOTE:
LEDa-G90-8
a) Use only this GE branded, Class 2 Power Supply, Model SA9A-05-05W,
manufactured by TDC that was provided with this product. DO NOT
use this adapter with any other product.
b) LEDs in this set are non-replaceable. Tampering with this set will
void the warranty.
CAUTION:
GE light sets come pre-attached to a plug. For end-to-end connections up to four (4) sets, you will need only one (1) plug. To
begin, choose one (1) set as your master set. This set would be the only set connected to a plug. Next, unscrew the coaxial
connector between the light set on all of the sets you would connect to your master set. Lastly, connect each set of lights
end-to-end using the coaxial connections, screwing each connection cap tightly.
Note: you may only add three (3) additional sets to your master set for a total of four (4) connected sets.
b) Do not replace or modify any connectors on this product, discard product if connector is damaged.
c) Make sure connectors are fully inserted and any connector rings are twisted until completely secured such that the ring can
no longer be turned and the two portions of the connector are completely assembled.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Modifications not approved by the party responsible for compliance could void user's authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
For questions and/or assistance, call customer service at 1-877-398-7337 or visit us on the web at www.GEholidaylighting.com
FOR INDOOR AND OUTDOOR USE
PRINTED IN CHINA
Nicolas Holiday Ltd. 204 Spring Hill Road Trumbull, CT 06611
©2021 Nicolas Holiday Limited, 9F., No. 37, Guangfu N. Rd Taipei, Taiwan 10560. All rights reserved
-CONTINUED FROM OTHER SIDE-
a) This lighting string is rated 2.2 Watts( 0.037 Amps), do not overload.
MADE IN CHINA
E246482 HC-21