Others; Troubleshooting; Specifications - Denon DP-300F Operating Instructions Manual

ENGLISH

Others

Troubleshooting

If a problem should arise, first check the following.
1. Are the connections correct?
2. Have you operated the player according to the Operating Instructions?
If this unit is not operating properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction. Disconnect the power immediately and contact your store of purchase.
Symptom Cause
• Power supply cord is not fully
inserted.
• Drive belt is detached from the
turntable.
Power does not turn
on.
Turntable does not turn.
• The pin-plug cable is not properly
connected.
• The amplifier's function is not set for
No sound is produced. the terminals to which the turntable is
connected.
• The replaceable stylus is not properly
mounted.
• The stylus or record is dirty.
The sound is scratchy,
• The stylus is worn or the record is
the stylus skips or the
scratched.
sound is distorted.
The sound is either
• The equalizer switch is not set at the
extremely weak or too proper position.
strong and distorted.
• The player is too close to the
speakers.
Howling is produced.
• The player is placed in an unstable
position.
• The playback sound is too loud.
The tone arm does not • The tone arm is clamped to the
move even when the armrest.
START button is
• The power supply cord is not properly
pressed.
connected.
Measures Page
• Check the connection. 4
• Check the drive belt and driving roller. 2
If the drive belt is detached from the
turntable, attach it using the
procedure described below.
1.Remove the turntable and turn it
upside down.
2.Catch the belt on the inside perimeter.
3.Turn the turntable back right side up
and pass the tape ribbon through the
hole and between the turn tape and
drive belt.
4.Mount the turntable, referring to the
assembly instructions on page 2.
• Check the connection. 4
• Check the amplifier's settings. 4
• Check the stylus. 7
• Remove the dirt or replace the stylus. 7
• Replace the stylus. 7
• Check the record. —
• Set the switch according to the 2
terminal to which the player is
connected.
• Move the player and speakers apart. —
• Check the player's place of installation. —
• Adjust the amplifier's volume. —
• Remove the tone arm's clamp. 2
• Check the connection of the power 4
supply cord.
ENGLISH

Specifications

Power supply:
Power consumption:
Maximum external dimensions:
Mass:
Drive type:
Motor:
Speed:
Wow & flutter:
S/N ratio:
Tone arm:
Effective arm length:
Overhang:
Cartridge:
Output voltage:
Optimum stylus pressure:
Replaceable stylus number:
Stylus pressure adjustment range: 0 ~ 39.2 mN (0 ~ 4.0 g)
Suitable cartridge empty weight : 44 mN ~ 93 mN (4.5 ~ 9.5 g)
Head shell weight:
Head shell part number:
* For purposes of improvement, specifications and design are subject to change without notice.
7
AC 120 V, 60 Hz
2 W
With dust cover closed :
434 (W) x 122 (H) x 381 (D) mm
(17-3/32" x 4-51/64" x 15") (including protruding parts)
With dust cover open :
434 (W) x 386 (H) x 413 (D) mm
(17-3/32" x 15-13/64" x 16-19/64") (including protruding parts)
5.5 kg (12 lbs 2 oz)
Belt drive
DC servo motor
33-1/3 rpm, 45 rpm
0.10 % W.R.M.S
60 dB
Static balance straight type tone arm
221.5 mm
19 mm
MM type
With equalizer OFF : 2.5 mV
With equalizer ON : 150 mV
19.6 mN (2.0 g)
DSN-85
One step 0.98 mN (0.1 g)
98 mN (10.0 g) (including screws and nuts)
PCL-310BK