Sealey SD250K Quick Start Manual

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. Safety
1.1. eleCtriCal Safety
Warning! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
do not pull or carry the appliance by the power cable.
8
do not pull the plug from the socket by the cable.
8
do not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or is
8
replaced immediately by a qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. general Safety
‰ ‰ Warning! ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
‰
‰
equipment.
Familiarise yourself with the application, limitations and potential hazards of the soldering gun.
9
Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
9
locate soldering gun in a suitable working area, keep area clean and free from unrelated materials. ensure that there is adequate
9
lighting.
Keep the soldering gun clean for best and safest performance.
9
ensure there are no flammable or combustible materials near the work area.
9
‰ ‰ Wear approved safety eye protection (standard spectacles are not adequate).
9
‰
‰ ‰ Wear appropriate protective clothing.
9
‰
ensure the workpiece is adequately held before operating the soldering gun.
9
Always lay the soldering gun on its side so that the tip cannot make contact with the work surface.
9
Remove excess solder from the soldering gun by wiping the tip on a damp, natural sponge.
9
ensure that when the soldering gun is put down during use that the tip is not near to or in contact with any material that may burn or
9
melt including the product's own supply lead.
‰ ‰ do not attempt to remove excess solder from the soldering gun by shaking it as hot solder may become airborne and cause burns
‰ 8
and blisters.
‰ ‰ do not allow children or pets into the area where the soldering is taking place.
‰ 8
do not attempt to cool the iron or gun with water.
8
Warning! disconnect the soldering gun from the mains power and allow it to cool before changing tips.
‰
do not operate the soldering gun when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
do not leave a hot soldering iron or gun unattended. (If you are leaving the work area even for a short period of time switch it off and
8
allow to cool.)
do not use the soldering gun for any purpose other than that for which it has been designed.
8
do not allow untrained persons to operate the soldering gun.
8
© Jack Sealey limited
Soldering Kit
Model no:
Hot surfaces Warning
Original Language Version
Sd250K
Indoor use only
Recommended fuse rating
3 Amp
SD250K Issue 2 (HF) 24/09/18