Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HGLRC Sector 5 V3 VTX
Summary of Contents for HGLRC Sector 5 V3 VTX
- Page 1 Sector 5 V3 VTX FPV Racing Drone Manual www.hglrc.com...
-
Page 2: Table Of Contents
Voltage and current parameters setting.....................9 Setting up the receiver..........................10 VTX serial port use.DJI serial port use....................11 GPS parameters setting...........................12 Check receiver signal..........................13 Select flight mode startup mode......................14 OSD settings..............................15 LED settings..............................16 Troubleshooting............................17 ..................Package IncIuded Sector 5 V3 FPV Racing Drone*1 Accessory Package*1 www.hglrc.com... -
Page 3: Product Specifications
Sector 5 V3 Frame Kit Flight Controller Zeus F722 Flight Controller 48A 4in1 ESC Zeus VTX 800MW Camera Caddx Ratel 2 Camera AEOLUS 2306.5 Motor Motor 4S KV2550 6S KV1900 Support Neceiver SBUS .PPM .DSMX Input Voltage 3-6S Lipo Weight 444.3g www.hglrc.com... -
Page 4: Interface Description
2.Interface Description www.hglrc.com... -
Page 5: Check The Flight Control Drive
3.Check the flight control drive 1. Long Press BOOT buttons.connect USB.The system automatically install the driver 2.Driver cannot be installed, please download ImpulseRC_Driver_Fixer 3.Double-click on the run(Plug in the flight controller to automatically install the driver) 4.open betaflight configurator enter DFU mode ， www.hglrc.com... - Page 6 5.Click Select firmware version Load firmware Waiting for 6.Click completion It will be prompted upon completion 7. open betaflight configurator computer. Betaflight Automatically assigned port click “Connect” Enter Controller plugged into the setup interface（Different computer COM） ， www.hglrc.com...
-
Page 7: Calibration Accelerometer
4. Calibration accelerometer 1. Put the aircraft horizontal and click“Reset Z axis” Click again 5.UART serial port use 1.UART1 uses the receiver 2.UART2 uses GPS 3.UART3 uses 5.8G VTX 4.UART4 uses DJI 5.UART6 uses ESC telemetry www.hglrc.com... -
Page 8: Select Aircraft Model
6.Select aircraft model Select model Click I understand the risks Click Click Push Master to check motor “ ” steering Master Steering can be changed at BLHeliSuite “ ” www.hglrc.com... -
Page 9: Choose Esc Protocol
1.Choose the right ESC protocol, the optional universal protocol DSHOT600. 8.Turn on ESC telemetry 1.Use BLHeli_32 ESC telemetry over a separate wire 2.Open ESC telemetry serial port.TX on the ESC needs to be connected to the RX6 on the flight controller to use the ESC telemetry www.hglrc.com... -
Page 10: Voltage And Current Parameters Setting
3.View telemetry data on OSD 9.Voltage and current parameters setting 1.Click Setting parameters www.hglrc.com... -
Page 11: Setting Up The Receiver
10.Setting up the receiver 1.Receiver connection diagram 2.Click have found UART1 Open the receiver serial port “ ” www.hglrc.com... - Page 12 3.Set the SBUS receiver 4.Set the PPM receiver 5.Set the DSMX receiver 6.Set the CRSF receiver www.hglrc.com...
- Page 13 11.VTX serial port use wiring . 1. 5.8VTX connection 2. DJI FPV Air Unit wiring www.hglrc.com...
- Page 14 4. DJI serial port opens 5.Use OSD to adjust VTX which displays information like battery voltage and mAh consumed while you fly. In addition, the Betaflight OSD can be used to configure the quadcopter, making in-field adjustments and tuning more convenient. MODE2 MODE1 www.hglrc.com...
- Page 15 The screen to the right shows the current vTX settings. Fromhere, you can change the frequency band, channel, and power level of the video transmitter. After making the changes, move the cursor to “Set” and press roll-right to confirm the settings. www.hglrc.com...
-
Page 16: Gps Parameters Setting
12.GPS parameters setting 1. GPS connection 2.Open the GPS serial port www.hglrc.com... -
Page 17: Check Receiver Signal
3.When using the GPS function, remember to configure the serial port (via the Ports tab). 13.Check receiver signal Check Check the remote control output signal 1.Click www.hglrc.com... -
Page 18: Select Flight Mode Startup Mode
Click channel (below are for reference only) 15.OSD settings the OSD Settings, according to the need to choose, drag Click the OSD schematic diagram of the parameters can be adjusted. www.hglrc.com... -
Page 19: Led Settings
Steady / Fast Flash / Breathing Light / Colorful Slow Flash LED light can be controlled via CH5(AUX1) of transmitter with Channel_Forwarding enabled. Click enter： resource servo 1 A08 SAVE 4. Click Forward aux channels to servo outputs 5.Click Turn on LED support www.hglrc.com... -
Page 20: Troubleshooting
● Keep focus on the polarity. Check carefully before power supply. ● Cut off the power when you connect, plug and pull anything. ● The refresh rate of PID and Gyroscope is up to 8K/8K. www.hglrc.com... - Page 21 "BBB" sound. There is only one sound. Please check if the ESC agreement is correct 3.The spin of the aircraft keeps spinning 1. Please check if the propeller is correct 2. Please check if the motor direction is correct www.hglrc.com...
Need help?
Do you have a question about the Sector 5 V3 VTX and is the answer not in the manual?
Questions and answers