Table of Contents
Advertisement
WARNING
To avoid damage from the electronic fuel injection system, do not remove or install the
battery when the ignition switch is in the "
" position.
The long-term storage of the vehicle could cause fuel and engine oil deterioration and
probably get into a non-start situation.
Service more frequently when operating in severe conditions such as dusty area, high
speed riding, frequent start and stop or extreme riding habit.
Make sure to keep away from any flammable materials such as dry grasses or leaves,
avoid them in contact with the exhaust pipe or muffler when parking the vehicle.
WARNI
Advertisement
Table of Contents
Related Manuals for KYMCO LIKE 150i
Summary of Contents for KYMCO LIKE 150i
- Page 1 WARNING To avoid damage from the electronic fuel injection system, do not remove or install the battery when the ignition switch is in the " " position. The long-term storage of the vehicle could cause fuel and engine oil deterioration and probably get into a non-start situation.
- Page 2 This Owner’s Manual contains important information on safety, operation and maintenance of KYMCO LIKE 150i/50i. Anyone who is going to ride should carefully read and understand the contents of this manual before riding. For personal safety, understand and follow all of the warnings contained in this Owner’s Manual and the labels attached on vehicle.
- Page 3 Vehicle Identification Number (VIN) Engine Serial Number (ESN) Record the Vehicle Identification Number① or ②, Engine Serial Number③, in the blanks above for a reference to assist you in ordering parts from the authorized KYMCO dealer or in case the vehicle is stolen.
-
Page 4: Table Of Contents
TABLE OF CONTENTS SECTION 1–SAFETY INTRODUCTION... SECTIONS MAINTENANCE....Forward............Maintenance Schedule......Scooter Safety..........Engine Oil..........Accessories & Modifications....... Engine Oil Replacement......Locations of Parts & Controls..... Transmission Fluid Change ....Air Filter Element Change ..... SECTION 2–CONTROLS & FEATURES... Throttle Operation ......... Ignition Switch.......... -
Page 5: Forward
Due to improvements or other changes, there may be slightly different from the vehicle. KYMCO reserves the right to make product and publication changes at any time without notice or obligation. -
Page 6: Scooter Safety
SCOOTER SAFETY Keep the vehicle in safe condition IMPORTANT SAFETY INFORMATION For safe riding, it's important to inspect the It will be used longer and pleasure if you take vehicle before every ride and perform all responsibility for your safety and understand the recommended maintenance. - Page 7 SCOOTER SAFETY PROTECTIVE CLOTHING For your safety, always wear an approved The recommended riding gears: motorcycle or scooter helmet, eyes protection, ①Wear gloves boots, gloves, long pants, and a long-sleeve shirt or ②Clothes should be fit properly jacket during a ride. ③Always wear a helmet with eye protection Helmets and protection ④Wear bright or reflective clothing...
-
Page 8: Accessories & Modifications
The addition of unsuitable accessories can lead to unsafe operation. It is not possible for KYMCO to test each accessory on the market or combinations of all the available accessories; however, the KYMCO dealer can assist you in selecting quality accessories and then install them correctly. -
Page 9: Locations Of Parts & Controls
LOCATION OF PARTS & CONTROLS 1 Rear Brake Lever 2 Headlight 3 Front Left Turn Signal Light 4 Fuel Filler Cap 5 Helmet Hook 6 Side Stand 7 Seat 8 Engine Number 9 Air Cleaner Rear Left Turn Signal Light Tail/Brake Light Luggage Box Reflector... - Page 10 LOCATION OF PARTS & CONTROLS Right Turn Signal Light Muffler Oil Filler Cap/dipstick Center Stand Rear Passenger Foot Peg Right Turn Signal Light Front Brake Lever Electric Starter Button Ignition Switch Vehicle Identification Number (VIN) ▆ NOTE: Your scooter may differ slightly in appearance from the images in this manual.
- Page 11 LOCATION OF PARTS & CONTROLS Right Rearview mirror Left Rearview mirror Right Turn Signal Light Left Turn Signal Light ▆ NOTE: Your scooter may differ slightly in appearance from the images in this manual.
-
Page 12: Section 2-Controls & Features
SECTION 2 - CONTROLS&FEATURES IGNITION SWITCH With the ignition key in the " " position (the To operate the ignition switch and it s functions: engine is not running), turn the counterclockwise “ ” Position: from the " " to the " "... -
Page 13: Security Shutter
CONTROLS & FEATURES SECURITY SHUTTER To open the ignition switch security shutter : Push the shut button on the ignition switch panel to close the security shutter. To shut the ignition switch security shutter : Insert the specific key until the notch aligned with the pin Turn clockwise to open the security shutter. -
Page 14: Instruments
CONTROLS & FEATURES INSTRUMENTS MODE Button ADJ Button... - Page 15 ˙Press ADJ to switch between km display Need to have immediate inspection by the and miles display. authorized KYMCO dealer. ② Fuel Level Meter: It displays how much fuel left in the fuel tank. When the fuel tank is near empty, it alerts the rider to refill the fuel tank as soon as possible.
- Page 16 CONTROLS & FEATURES ① Oil Trip: It flashes every 2000km to remind you to do engine oil service. You need to reset it after you change the engine oil. ② Belt Trip: It flashes every 20000km to remind you to change the drive belt. You need to reset it after you change the drive belt.
- Page 17 CONTROLS & FEATURES Service Indicator Reset: After you change the engine oil or the drive belt , you need to reset the Service Indicator. 1.Push MODE button, the multifunction display will change (ODO→TRIP→OIL TRIP→BELT TRIP) repeatedly in sequence. 2.Choose OIL TRIP mode or BELT TRIP mode，press MODE button and ADJ button at the same time for 2 seconds and the display will turns to 0.0,the service indicator...
- Page 18 CONTROLS & FEATURES Adjust clock The setting procedure: 1. Turn the ignition switch to the ON position. 2. Push the MODE button t o toggle between ODO mode, trip mode, oil trip and belt trip . Choose ODO mode. ▆ digital clock can be only adjusted in ODO NOTE: The mode.
- Page 19 ABS system. ▆ NOTE: If the ABS indicates a fault, it’s very important to make the authorized KYMCO dealer to check the ABS system immediately.
-
Page 20: Usb Power Supply
CONTROLS & FEATURES Accessory Socket This vehicle is equipped with the accessory USB power socket which provides a function to charge the mobile phone with capacity compliance as below. ˙To use the accessory USB power supply, turn on the ignition switch, and then start the engine. ①... -
Page 21: Passenger Foot Pegs
CONTROLS & FEATURES Passenger foot pegs Your scooter is equipped with additional pegs for use when you are carrying a passenger. 1.To move the passenger pegs from the scooter’s body, press the pegs back-end ① . 2. When you are not carrying a passenger, press the pegs back into place. -
Page 22: Right-Hand Handlebar Switch
Right handlebar switch Starter button①: Press starter button " " and pull brake lever in the meantime to actuate the starter motor. ▆NOTE: Hold the left brake lever, or the starter motor won’t work. Don’t press the starter button while the engine is running. -
Page 23: Left-Hand Handlebar Switch
CONTROLS & FEATURES Left handlebar switch Turn signal switch③: Push to signal other drivers for an intention to make turn or change lane. The turn signal light is blinking while the switch is pushed left or right. for left turn. "... -
Page 24: Fuel Recommendation
CONTROLS & FEATURES Fuel level inspection / Refilling If the low fuel indicator blinks, quickly refill the fuel tank with the specified unleaded gasoline. Fuel tank filler: To refuel, do the following: 1. Open the fuel tank filler cover. 2. Use the ignition key to unlock the fuel cap. 3. -
Page 25: Seat
CONTROLS & FEATURES Seat To unlock the seat With the ignition key at the " " position (the engine is running), push the key in and turn it counterclockwise from " " to the " " position. With the ignition key in the " "... -
Page 26: Helmet Holder And Hook
CONTROLS & FEATURES HOOK Helmet Holder If you need to use the front hook, press To use the helmet holders, open the seat and button the hidden hook will come out. hang the helmet on the holder hook, then lock the seat securely. -
Page 27: Suspension
CONTROLS & FEATUREs Suspension Each shock absorber assembly is equipped with a spring preload adjusting ring. Adjust the spring preload as follows. To increase the spring preload and thereby harden the suspension, turn the adjusting ring on each shock absorber assembly in direction (a). To decrease the spring preload and thereby soften the suspension, turn the adjusting ring on each shock absorber assembly in direction (b). -
Page 28: Section 3-Operation
Check operation; make sure there is no motorcycle and check its condition. If you detect brake fluid leakage. any problem, be sure to deal with it, or have the KYMCO dealer to fix it. 4. Tires: Check condition and inflation pressure. WARNING 5. -
Page 29: Break-In
OPERATION Break-In Avoid constant low speed The first 1600km (1000 miles) of riding is Operate the engine at constant low speed very important to the life of usage. Proper even of light load may cause the running break-in operation during this period will part a fit-in problem. -
Page 30: Starting The Engine
OPERATION Starting the engine Always follow the proper starting procedure described here and on the following pages. CAUTION To protect the catalytic converter in the engine's exhaust muffler, avoid idling too long and do not use leaded gasoline. CAUTION To prevent damage to the starter motor, do not operate the starter motor for more than 5 seconds at a time. - Page 31 OPERATION 4. Squeeze the left (rear) brake lever to connect electric power for ready to start engine . 5. Press the starter button ① with the throttle closed, releases it at once as the engine starts. 6. Keep the throttle closed while warming up the engine.
- Page 32 OPERATION ABS SYSTEM (For ABS model) Limitations of ABS The ABS system is the equipment that ABS does not apply the brakes automatically. It prevents wheel lockup in case of an needs to apply the brakes at the right time and emergency braking, thus is capable to with the right amount of braking force.
-
Page 33: Sections Maintenance
It will involved in a crash, be sure to have the also help reduce air pollution and maximize fuel KYMCO dealer inspect all major parts, even if economy. you are able to make some repairs. -
Page 34: Maintenance Schedule
Maintenance should be performed according to the design standards and specifications by the authorized KYMCO dealer. Be serviced by the KYMCO dealer, unless you have the proper tools, service data and are technically qualified. - Page 35 MAINTENANCE WHICHEVER FREQUENCY ODOMETER READING (NOTE1) COMES FIRST X 1000 km REFER X 1000 mi ITEM PAGE MONTH AIR CLEANER NOTE2 SPARK PLUG NOTE4 THROTTLE OPERATION VALVE CLEARANCE FUEL LINE CRANKCASE BREATHER NOTE3 ENGINE OIL NOTE7 ENGINE OIL SCREEN ENGINE IDLE SPEED TRANSMISSION OIL NOTE5 DRIVE BELT...
- Page 36 MAINTENANCE WHICHEVER FREQUENCY ODOMETER READING (NOTE1) COMES FIRST X 1000 km REFER X 1000 mi ITEM PAGE MONTH CLUTCH SHOE WEAR BRAKE FLUID NOTE6 Replace at every10000km or every year BRAKE PAD WEAR BRAKE SYSTEM BRAKE LIGHT SWITCH STEERING BEARINGS HEADLIGHT AIM NUTS,BOLTS,FASTENERS WHEEL/TIRES...
-
Page 37: Engine Oil
① and low line ② on the oil level dipstick ③ If the viscosity grade is not compliable, choose alternative engine oil according to the following chart. LIKE 150i Full capacity: 0.9 L (0.95 US QT) CAUTION Exchange capacity: 0.8L (0.84 US QT) -
Page 38: Engine Oil Replacement
MAINTENANCE Engine oil replacement ● Start engine and keep idling for a few minutes. Engine oil quality is the major factor that affects ● Stop the engine and stand the scooter on level engine life. Change your scooter's engine oil as specified in the maintenance schedule. -
Page 39: Transmission Fluid Change
, and then slowly rotate the rear wheel to drain the gear oil off. 4. Fill with the recommended oil to reach the capacity LIKE 150i listed below. 5. Install the transmission filler bolt and tighten it to the specified torque. -
Page 40: Air Filter Element Change
MAINTENANCE Air cleaner filter element(FOR LIKE 150i) The air cleaner filter element should be serviced at regular intervals by the KYMCO dealer. Removal of the air cleaner cap (1)Remove the screws from the air cleaner (2)Remove the screws from the right side of the scooter. - Page 41 Remove the screws of the air cleaner filter. Replace it with a new one. ▆ NOTE: Air cleaner is an important part of your scooter ,please go to a KYMCO dealer for air cleaner service. The air cleaner filter CAUTION Improper installation for the filter can cause water or dirt to enter the engine causing premature wear.
- Page 42 MAINTENANCE Air cleaner filter element(FOR LIKE 50i) The air cleaner filter element should be serviced at regular intervals by the KYMCO dealer. Removal of the air cleaner cap (1)Remove the screws from the air cleaner (2)Remove the air cleaner cap .
- Page 43 Replace it with a new one. ▆ NOTE:Air cleaner is an important part of your scooter ,please go to a KYMCO dealer for air cleaner service. CAUTION The air cleaner filter Improper installation for the filter can cause water or dirt to enter the engine causing premature wear.Using the wrong KYMCO air...
-
Page 44: Throttle Operation
2. Measure the throttle free play as shown at right. Throttle free play: 2.0 - 6.0 mm (0.08-0.24 in) ▆ If your scooter’s throttle free play requires NOTE: adjustment, contact you KYMCO dealer for service. -
Page 45: Spark Plug
After cleaning, check to adjust the spark plug gap to specified limit by using a spark plug gap thickness gauge. The spark plug should be replaced periodically. Recommend to consult with the KYMCO dealer when choosing an alternative spark plug instead. Recommended spark plug：CR8E(like 150i) CR7HSA/CR6HSA(like 50i) 0.7~0.8 mm... -
Page 46: Brake Fluid Level Inspection
MAINTENANCE Brake fluid Brake fluid level inspection With the scooter in an upright position, check the front and rear fluid level. Change the brake fluid at the time specified in the maintenance schedule. The fluid level should be above the ①... -
Page 47: Brake Pad Inspection
MAINTENANCE Brake Pad Inspection Inspect the thickness of brake pad to verify if there is enough lining to brake properly. If the wear indicated groove at the brake pad is no longer visible, this means that the brake pad is worn and requires replacement. Before riding, apply braking several times to reach the proper lever stroke and firm feel on braking action that will ensure the... - Page 48 Brake lever free play inspection Before riding, inspect the rear brake lever free play and adjust it to the 10~20mm specified amount. Free play:10~20mm (For like 50i model) Parking Brake Parking Brake 1.Parking Brake is a device which can Pull prevent the scooter from moving when you park on a slope.
- Page 49 Rear brake adjustment (for Drum model ) Rotate the adjuster nut ① clockwise to reduce the brake lever free play. Rotate the adjuster nut counterclockwise to increase the brake lever play. Rear brake pad wear inspection (for Drum model ) The free-play is the measured distance between the brake lever at rest and a fully applied brake.
-
Page 50: Battery
Avoid any contact with skin, eyes or contact the KYMCO dealer immediately. clothing and always shield your eyes when ① ● Disconnect the negative (-) terminal working near batteries. -
Page 51: Fuse
∎ Never use a fuse of different rating. Fuse Specifications ∎ If the new fuse blows in a short time, consult 10A*1 15A*1 the KYMCO dealer immediately. Fuse Specifications (ABS Mode) 15A*1 10 A*2 25A*1 Good Blown... -
Page 52: Tires
MAINTENANCE Tires Tire pressure WARNING Insufficient tire pressure not only advances wear but also affects the riding stability. Under- Fail to follow the instruction below may result inflated tires make turning not smooth and over- in an accident due to tire failure. The rider’s inflated tires decrease the contact area with the personal safety is dependent on the ground, which can lead to skid and loss of... -
Page 53: Tires Inspection
An improperly repaired, installed, or balanced tire can cause you to lose control of your scooter or shorten tire life. Ask the authorized KYMCO dealer, or a qualified tire shop to perform tire repair, replacement, and balancing due to the proper tools and experience are required. -
Page 54: Clean The Vehicle
MAINTENANCE Washing your scooter Cleaning Clean your scooter regularly to protect the 1.Rinse the scooter thoroughly with cool surface finishes and inspect for damage, wear, water to remove any loose dirt. and oil, coolant or brake fluid leakage. 2. Clean the scooter with a sponge or soft Avoid cleaning products that are not specifically cloth using cool water. -
Page 55: Crankcase Blow-By Drain
Crankcase Blow-by Drain ① The air cleaner has a drain tube that is for draining the oil condensed fluid from the crankcase. When the fluid has accumulated to a certain amount ② in the transparent drain tube, remove the clip ③... -
Page 56: Storage
MAINTENANCE STORAGE Removal from Storage Take necessary steps to be in good condition ●Remove cover from the vehicle for next use after long storage. ●Check the battery voltage or charge it if necessary, and then install it in the vehicle. ●Perform any necessary periodic maintenance ●Fill the fuel tank with fuel. -
Page 57: Emission Control
EMISSION CONTROL Crankcase Emission Control System The motorcycle is equipped with a closed crankcase system. Blow-by gas is recycled into the combustion chamber via the intake system. This arrangement is to prevent blow-by gas from spreading to the atmosphere. Exhaust Emission Control System The exhaust emission from the motorcycle is controlled by combustion management, fuel delivery, ignition setting and exhaust system. -
Page 58: Maintenance Record
MAINTENANCE RECORD DATE MILEAGE SERVICE PERFORMED&NOTES... - Page 59 MAINTENANCE RECORD DATE MILEAGE SERVICE PERFORMED&NOTES...
-
Page 60: Specifications
LIKE 150i SPECIFICATIONS Dimensions Chassis Overall length ........... 1915 mm Tire size, front........110/70 – 12 Overall width..........680 mm Tire size, rear........130/70 –12 Overall height ..........1130mm Brake (front) ........ABS Wheel base..........1315 mm Brake (rear) ..........ABS Seat height ..........790 mm Curb weight.......... - Page 61 LIKE 50i SPECIFICATIONS Dimensions Chassis Overall length ........... 1915mm Tire size, front.........110/70 – 12 Overall width..........680 mm Tire size, rear........130/70 – 12 Overall height ........... 1130mm Brake (front) ..........DISK Wheel base..........1315 mm Brake (rear)..........DRUM Seat height ..........810 mm Curb weight..........
Need help?
Do you have a question about the LIKE 150i and is the answer not in the manual?
Questions and answers