Table of Contents
Advertisement
Quick Links
2018/2/9
Cameras
>
Camera Models
daA1280-54um
The daA1280-54um
mono CMOS sensor delivers 54 frames per second at 1.2 MP resolution.
In this topic
Variants
Speci cations
General Speci cations
Spectral Response
Mechanical Speci cations
Camera Dimensions and Mounting Points
Maximum Allowed Lens Intrusion
Stress Test Results
Requirements
Environmental Requirements
Temperature and Humidity
Heat Dissipation
Electrical Requirements
Camera Power
General Purpose I/O Lines
Circuit Diagrams
Cable Requirements
USB 3.0 Cable
I/O Cable
USB 2.0 Compatibility
Physical Interface
Camera Connectors and Status LED
USB 3.0 Connector
I/O Connector Pin Numbering and Assignments
I/O Board
Precautions
Installation
Features
https://docs.baslerweb.com/?filter=Camera:acA2500-14gm#t=en%2Fdaa1280-54um.htm
>
Basler dart USB 3.0
Basler dart USB 3.0 camera
daA1280-54um
> daA1280-54um
with an ON Semiconductor AR0134
1/11
Advertisement
Table of Contents
Related Manuals for Basler daA1280-54um
Summary of Contents for Basler daA1280-54um
- Page 1 Camera Models > Basler dart USB 3.0 > daA1280-54um daA1280-54um The daA1280-54um Basler dart USB 3.0 camera with an ON Semiconductor AR0134 mono CMOS sensor delivers 54 frames per second at 1.2 MP resolution. In this topic Variants Speci cations...
-
Page 2: General Speci Cations
CS-mount: Consists of a circuit board and a camera front. CS-mount lenses can be mounted in the lens mount on the camera front. Basler dart S-mount color cameras are not equipped with an IR cut lter. If you want to operate a Basler dart S-mount color camera with an IR cut lter, you must attach a lens with an integrated IR cut lter to the camera. -
Page 3: Spectral Response
SFNC 2.x), USB3 Vision, REACH Conformity The EU Declaration of Conformity is available on the Basler website. Basler pylon Camera Software Suite (version 4.2 or higher) Software Available for Windows, Linux x86, Linux ARM, and OS X Cables for your camera model... -
Page 4: Camera Dimensions And Mounting Points
2018/2/9 daA1280-54um The spectral response curve excludes lens characteristics and light source characteristics. Mechanical Speci cations Camera Dimensions and Mounting Points Bare Board Variant S-Mount Variant https://docs.baslerweb.com/?filter=Camera:acA2500-14gm#t=en%2Fdaa1280-54um.htm 4/11... -
Page 5: Environmental Requirements
2018/2/9 daA1280-54um CS-Mount Variant Maximum Allowed Lens Intrusion → See Maximum Allowed Lens Intrusion. Stress Test Results → See Stress Test Results. Requirements Environmental Requirements Temperature and Humidity S-Mount and CS- Bare Board Variant Mount Variant Device temperature during 0–75 °C (32–167 °F) 0–50 °C (32–167 °F) -
Page 6: Heat Dissipation
2018/2/9 daA1280-54um storage -20–80 °C (-4–176 °F) -20–80 °C (-4–176 °F) 20–80 %, relative, non- 20–80 %, relative, non- Humidity condensing condensing Ambient temperature according max. 50 °C (122 °F) max. 50 °C (122 °F) to UL 60950-1 UL 60950-1 test conditions: no lens attached to camera; no heat dissipation measures;... -
Page 7: General Purpose I/O Lines
2018/2/9 daA1280-54um You must supply camera power that complies with the Universal Serial Bus 3.0 speci cation. The camera’s nominal operating voltage is 5 VDC, effective on the camera’s connector. General Purpose I/O Lines The camera has two direct-coupled GPIO lines that are accessed via contact 3 and 4 of the I/O connector on the back of the board. -
Page 8: Circuit Diagrams
USB 2.0 port. Otherwise, the camera may not work properly. avoid EMI, cables must be shielded, as speci ed in the USB 3.0 standard. Basler recommends using USB 3.0 cables from the Basler Vision Components range. -
Page 9: Usb 2.0 Compatibility
This also affects other aspects of the camera performance, e.g., the sensor readout time, trigger delay, jitter, or the precision of the exposure time set. If you operate a daA1280-54um/uc camera on a USB 2.0 port, image noise may increase. This is because the image sensor of the camera produces more image noise at low frame rates. -
Page 10: Usb 3.0 Connector
Connection assignments and numbering adhere to the Universal Serial Bus 3.0 standard. The recommended mating connector is any standard Micro-B USB 3.0 plug. Depending on how you integrate the Basler dart into your system, you must select a corresponding USB 3.0 connector that matches the orientation of the dart USB 3.0 connector in the mounted position. -
Page 11: Installation
Allows you to trigger multiple dart USB 3.0 cameras simultaneously. Protects the dart camera against short circuits. The board can be mounted on the back of the Basler dart circuit board. The connectors of the I/O board replace the standard I/O connector of the Basler dart.
Need help?
Do you have a question about the daA1280-54um and is the answer not in the manual?
Questions and answers