Related Manuals for Seagate ST3000DM008
Summary of Contents for Seagate ST3000DM008
- Page 1 Product Manual Standard models Self-Encryption models ST3000DM008 ST3000DM009 ST2000DM006 ST2000DM007 ST1000DM010 ST500DM009 100804187, Rev. D June 2017...
- Page 2 Seagate, Seagate Technology, BarraCuda and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. AcuTrac, OptiCache, Smar- tAlign and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners.
-
Page 3: Table Of Contents
Seagate® Technology Support Services ........ - Page 4 S.M.A.R.T. commands ............. . 36 Seagate BarraCuda Product Manual, Rev. D...
- Page 5 Mounting dimensions (configuration 3) ............25 Seagate BarraCuda Product Manual, Rev. D...
-
Page 6: Seagate® Technology Support Services
For information regarding online support and services, visit: http://www.seagate.com/contacts/ For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/data-recovery-services/ For Seagate OEM, Distribution partner and reseller portals, visit: http://www.seagate.com/partners/ Seagate BarraCuda Product Manual, Rev. D... -
Page 7: Introduction
• Seagate AcuTrac™ servo technology delivers dependable performance, even with hard drive track widths of only 75 nanometers. • Seagate OptiCache™ technology boosts overall performance by as much as 45% over the previous generation. • Seagate SmartAlign™ technology provides a simple, transparent migration to Advanced Format 4K sectors •... -
Page 8: About The Sata Interface
SATA ports are represented to host software as a Device 0 (master) and Device 1 Note (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical SATA environment. Seagate BarraCuda Product Manual, Rev. D... -
Page 9: Drive Specifications
2.0A or 2.5A 2.0A Voltage tolerance (including noise) 5V: ±5% 12V: +10% / -7.5% Non-Operating ambient temperature (°C) –40° to 70° Operating ambient temperature (min °C) 0° † 60° Operating temperature (Drive case max °C) Seagate BarraCuda Product Manual, Rev. D... - Page 10 During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. † Seagate does not recommend operating at sustained case temperatures above 60°C. Operating at higher temperatures will reduce useful life of the product. Seagate BarraCuda Product Manual, Rev. D...
-
Page 11: Formatted Capacity
Areal density (Gb/in Spindle speed (RPM) 7200 ± 0.2% Internal data transfer rate (Mb/s max) 2147 Maximum sustained data transfer rate, OD read (MB/s) Average data rate, read/write (MB/s) I/O data-transfer rate (MB/s max) Seagate BarraCuda Product Manual, Rev. D... -
Page 12: Physical Characteristics
(such as track-to-track and average), are expected to meet the noted values. However, Note due to the manner in which these drives are formatted, benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications. Seagate BarraCuda Product Manual, Rev. D... -
Page 13: Start/Stop Times
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track location. • Standby mode During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/write elec- tronics are in power-down mode. Seagate BarraCuda Product Manual, Rev. D... -
Page 14: Conducted Noise
• Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10MHz. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. Note Seagate BarraCuda Product Manual, Rev. D... -
Page 15: Voltage Tolerance
If the standby timer reaches zero before any drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all com- mands and returns to Active mode when disk access is necessary. Seagate BarraCuda Product Manual, Rev. D... -
Page 16: Environmental Specifications
† Operating temperature (Drive case max °C) 60° † Seagate does not recommend operating at sustained case temperatures above 60°C. Operating at higher temperatures will reduce useful life of the product. 2.9.2 Temperature gradient Operating 20°C per hour (68°F per hour max), without condensation Non-operating 30°C per hour (86°F per hour max) -
Page 17: Shock
The maximum non-operating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below. 5Hz to 22Hz 3.0 Gs (Limited displacement) 22Hz to 350Hz 3.0 Gs 350Hz to 500Hz 3.0 Gs Seagate BarraCuda Product Manual, Rev. D... -
Page 18: Acoustics
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO 389-7) to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. -
Page 19: Reliability
None required. 2.12.2 Storage Maximum storage periods are 180 days within original unopened Seagate shipping package or 60 days unpackaged within the defined non-operating limits (refer to environmental section in this manual). Storage can be extended to 1 year packaged or unpackaged under optimal environmental conditions (25°C, <40% relative humidity non-condensing, and non-corrosive environment). -
Page 20: Fcc Verification
As a subassembly, no Federal Communications Commission verification or certification of the device is required. Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. -
Page 21: China Requirements - China Rohs 2
The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. -
Page 22: Configuring And Mounting The Drive
For installations which require cables, users can connect the drive as illustrated in Figure 1 Figure 1 Attaching SATA cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation. BarraCuda drives support latching SATA connectors. Seagate BarraCuda Product Manual, Rev. D... -
Page 23: Drive Mounting
3 MINIMUM THREAD DEPTH 0.12 MAXIMUM FASTENER PENETRATION 2x 3.750 in 95.25 mm Drawings are for mounting hole reference only. Note PCBA show in pictorial only and can vary based on specific customer configurations. Seagate BarraCuda Product Manual, Rev. D... - Page 24 Configuring and Mounting the Drive Seagate utilizes three base decks for 1TB and 500GB capacities, as shown below. Figure 3 Mounting dimensions (configuration 1) 5.787 MAX .138 C L OF CONNECTOR DATUM B .814 4.010 MAX C L OF DRIVE TOP OF LABEL .640 .050...
- Page 25 3 MINIMUM THREAD DEPTH 0.14 MAXIMUM FASTENER PENETRATION MOUNTING HOLES 2X 3.750 2X .125 Drawings are for mounting hole reference only. Note PCBA show in pictorial only and can vary based on specific customer configurations. Seagate BarraCuda Product Manual, Rev. D...
- Page 26 3 MINIMUM THREAD DEPTH 0.15 MAXIMUM FASTENER PENETRATION 2x 3.750 in 95.25 mm Drawings are for mounting hole reference only. Note PCBA show in pictorial only and can vary based on specific customer configurations. Seagate BarraCuda Product Manual, Rev. D...
-
Page 27: About (Sed) Self-Encrypting Drives
Trusted Send • Trusted Receive These commands are used to convey the TCG protocol to and from the drive in their command payloads. Seagate Secure SEDs also support TCG Single User Mode, which can be disabled. 4.1 Data Encryption Encrypting drives use one inline encryption engine within each drive employing AES-256 algorithms in Cipher Block Chaining (CBC) mode to encrypt all data prior to being written on the media and to decrypt all data as it is read from the media. -
Page 28: Drive Locking
In addition to providing a locking mechanism to prevent unwanted firmware download attempts, the drive also only accepts download files which have been cryptographically signed by the appropriate Seagate Design Center. Three conditions must be met before the drive will allow the download operation: 1. -
Page 29: Sata Interface
There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration. • All used voltage pins (V ) must be terminated. Seagate BarraCuda Product Manual, Rev. D... -
Page 30: Supported Ata Commands
Read Native Max Address Extended Read Sectors Read Sectors Extended Read Sectors Without Retries Read Verify Sectors Read Verify Sectors Extended Read Verify Sectors Without Retries Recalibrate Security Disable Password Security Erase Prepare Security Erase Unit Seagate BarraCuda Product Manual, Rev. D... - Page 31 Write DMA Extended Write DMA FUA Extended Write DMA Without Retries Write Log Extended Write Multiple Write Multiple Extended Write Multiple FUA Extended Write Sectors Write Sectors Without Retries Write Sectors Extended Write Uncorrectable Seagate BarraCuda Product Manual, Rev. D...
-
Page 32: Identify Device Command
Number of current logical heads xxxx Number of current logical sectors per logical track xxxx 57–58 Current capacity in sectors xxxx Number of sectors transferred during a Read Multiple xxxx or Write Multiple command Seagate BarraCuda Product Manual, Rev. D... - Page 33 Ultra DMA support and current mode (see note following this table) xx7F Security erase time 0039 Enhanced security erase time 0039 Master password revision code FFFE Hardware reset value xxxx Automatic acoustic management 8080 95–99 ATA-reserved 0000 Seagate BarraCuda Product Manual, Rev. D...
- Page 34 Integrity word xxA5 Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported. Note See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data. Note Seagate BarraCuda Product Manual, Rev. D...
- Page 35 Ultra DMA mode 2 is currently active. Ultra DMA mode 3 is currently active. Ultra DMA mode 4 is currently active. Ultra DMA mode 5 is currently active. Ultra DMA mode 6 is currently active. Seagate BarraCuda Product Manual, Rev. D...
-
Page 36: Set Features Command
Disable use of SATA features Enable read look-ahead (read cache) feature (default). Report full capacity available At power-on, or after a hardware or software reset, the default values of the features are as indicated above. Note Seagate BarraCuda Product Manual, Rev. D... -
Page 37: Commands
S.M.A.R.T. Enable Operations S.M.A.R.T. Disable Operations S.M.A.R.T. Return Status If an appropriate code is not written to the Features Register, the Note command is aborted and 0x 04 (abort) is written to the Error register. Seagate BarraCuda Product Manual, Rev. D... - Page 38 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100804187, Rev. D...
Need help?
Do you have a question about the ST3000DM008 and is the answer not in the manual?
Questions and answers