Page 1
CHINA CELLULAR GSM TELEPHONE SGH-S108 Manual SERVICE China Cellular GSM Telephone CONTENTS 1. Exploded Views and Parts List 2. Electrical Parts List 3. Block Diagrams 4. PCB Diagrams 5. Flow Chart of Troubleshooting...
Page 2
ELECTRONICS ⓒ Samsung Electronics Co.,Ltd. December. 2002 Printed in Korea. Code No.: GH68-03165A BASIC.
Page 11
2. SGH-S108 Exploded View and its Parts list 1. Cellular phone Exploded View SAMSUNG Proprietary-Contents may change without notice...
Page 12
SGH-S108 Exploded view and its Part list 2. Cellular phone Parts list Description SEC. CODE Remark DUAL WINDOW LCD GH72-05435A FOLDER UPPER GH75-02604A GH07-00179A MOTOR 3101-001295 SPEAKER 3001-001297 FOLDER LOWER GH75-02079A SCREW 6001-001478 SCREW CAP GH74-02036A WINDOW LCD GH72-04716A FRONT COVER...
Page 13
SGH-S108 Exploded view and its Part list 3. Test Jig (GH80-00865A) 3-1. RF Test Cable 3-2. Test Cable 3-3. Serial Cable (GH39-00093A) (GH39-00165A) 3-4. Power Supply Cable 3-5. DATA CABLE 3-6. TA (GH44-00312D) (GH39-00176A) SAMSUNG Proprietary-Contents may change without notice...
Page 14
SGH-S108 Exploded view and its Part list SAMSUNG Proprietary-Contents may change without notice...
Page 15
FILTER 100KHz SI4201 1/ 2 FILTER DSP16000 SI4200 SERIAL DATA, SERIAL DATA ARM7TDMI CLK, INTERFACE GSM:890MHz~ 915MHz D E T DCS:1710MHz~ 1785MHz TCVCXO 13 MHz PCS:1850MHz~ 1910MHz A F C C L K SI4133T SAMSUNG Proprietary-Contents may change without notice...
Page 19
5. SGH-S108 Flow Chart of Troubleshooting 1. Power ON ' Power On ' does not work Check the current consumption Current consumption Download again >=100mA Check the V bat. Voltage Voltage >= 3.3V Charge the Battery Check the pin of U100 Check U100 and C113 pin#15 >= 2.8V...
Page 20
SGH-S108 Exploded view and its Part list 2. Initialization Initialization Failure The pin #13 of U100 = Check the U100 1.8V and (If it has some problem, it has to be the pin #15 of U100 ㆃ replaced.) 2.825V ?
Page 21
SGH-S108 Exploded view and its Part list 3. Charging Abnormal charging operation The pin #22, #23 of CN300 is TA_VEXT ㆃ Replace TA or Check CN300 The pin #2 of U102 is Check the U102 "low"? The pin #3 of Q101 is Check the Q101 "low"?
Page 22
SGH-S108 Exploded view and its Part list 4. Sim "Insert SIM" is displayed on the LCD Is there any Signals Check the U601 pin#64, #65, #66 of CN100? Is there any Signals Check the U100 pin#61, #62, #63 of CN100?
Page 23
SGH-S108 Exploded view and its Part list 5. Microphone Part Microphone does not work Is the assembled status Reassemble the microphone of microphone O.K? Check the reference voltage on mic path Solder the microphone again or C409 ㆃ 2.0V Replace C400,C409,R405,R406,R409,R410...
Page 24
SGH-S108 Exploded view and its Part list 6. Speaker There is no sound from Speaker Is the terminal of Speaker Replace the Speaker O.K.? Are there any signals Check LCD or Replace CN201 at the C221,C228? The type of sound...
Page 25
SGH-S108 Exploded view and its Part list 7. RX_EGSM CONTINUOUS RX ON R F IN PUT : 62CH AMP : -50dBm Check soldered statu s NORM AL CONDITION catch the channel? L1000,C1001,C1002 YE S CON1 F1002 CHE CK solder aga in or c hange pin#2 ≥...
Page 26
SGH-S108 Exploded view and its Part list 8. TX_EGSM CONTINUOUS TX ON CONDITION F1002 F1002 TX POWER DAC:500 CODE U700,U701 pin#13:about pin#11= 2.85 V? APPLIED 2~3 dBm? check & change CH:62 RBW : 100KHz VBW : 100KHz SPAN : 10MHz U1001 pin#5: REF LEV.
Page 27
SGH-S108 Exploded view and its Part list 9. RX_DCS CONTINUOU S RX ON RF INPUT : 698CH AMP : -50dBm NORM AL Check soldered s tatus of CONDITION L1000,C1001,C1002 F1002 CHECK CON1 pin#2 ≥ 65dBm ? solder again or change...
Page 28
SGH-S108 Exploded view and its Part list 10. TX_DCS F1002 F1002 pin#7: U700,U702 CONTINUOUS TX ON CONDITION pin#11= 2.85 about 2~3 check & change TX POWER DAC:500 CODE APPLIED dBm? CH:698CH RBW : 100KHz VBW : 100KHz SPAN : 10MHz REF LEV.
Page 29
SGH-S108 Exploded view and its Part list 11. RX_PCS CONTINUOUS RX ON RF I NPUT : 62CH AMP : -50dBm NORMAL CONDI TION Check soldered status of catch the channel? L1000,C1001,C1002 F1002 CHECK CON1 pin#2 ≥ 65dBm ? solder again or change...
Page 30
SGH-S108 Exploded view and its Part list 12. TX_PCS F1002 F1002 pin#7: U700,U701 CONTINUOUS TX ON CONDI TION pin#11= 2.85 about 2~3 check & change TX POWER DAC:500 CODE APPLIED dBm? CH:62 RBW : 100KHz VBW : 100KHz SPAN : 10MHz REF LEV.