Advertisement
Quick Links
Advertisement
Related Manuals for Deagostini MODEL SPACE Lamborghini Countach LP 500S
Summary of Contents for Deagostini MODEL SPACE Lamborghini Countach LP 500S
- Page 1 WALTER WOLF MODEL Pack ™...
- Page 2 Lamborghini Countach LP 500S CONTENTS ™ Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP. Published in the UK by De Agostini UK Ltd, Battersea Studios 2, Assembly Guide Stages 78-80 82 Silverthorne Road, London SW8 3HE. Published in the USA by De Agostini Publishing USA, Inc., 915 Broadway, Suite 609, New York, NY 10010.
- Page 3 Lamborghini Countach LP 500S Stage 78 The right door Parts Right door Wiper Steering crank base (silver) Steering crank (silver) 2.6 × 6mm screws × 22 2.6 × 3mm screws with washers × 2 2 × 5mm self-tapping screws × 2 2.3 ×...
- Page 4 Lamborghini Countach LP 500S Align the holes of door lock part A (Stage 77) with the posts Before fitting lock part A, insert the pin on the inside (inset) Lower lock part A onto the posts on the inside of the door. on the inside of the right door.
- Page 5 Lamborghini Countach LP 500S Insert the tip of the screw into the hole above lock Tighten the screw into the hole. Apply some masking tape to the protective film covering part A, aligning the flat edge of the washer with the right window (Stage 77).
- Page 6 Lamborghini Countach LP 500S Insert a 2.6 × 6mm screw into the front Half-tighten the screw into the hole. Half-tighten a second 2.6 × 6mm screw Place the right door hinge and the door hole of the window (arrowed). into the hole towards the rear of the hinge holder (Stage 77) as shown above.
- Page 7 Lamborghini Countach LP 500S Push the hinge holder under the pin, and Insert a 2.6 × 5mm screw with washer Tighten the screw into place. adjust its position to align the hole in the (Stage 74) into the hole in the holder. holder with the hole in the door.
- Page 8 Lamborghini Countach LP 500S Tighten the screw into the hole. Align the posts on the inside of the door Push the holes of the right door inner onto Test the door lock. When you press it in, with the holes in the right door inner the posts on the door.
-
Page 9: Assembling The Body
Lamborghini Countach LP 500S Stage 79 Assembling the body Parts Left door sill Right door sill Rear under grill 1.7 × 3mm screws × 5 Tools Prepare Phillips screwdriver (size 0) Front compartment (Stage 68) Main body assembly (Stage 77) 2.3 ×... - Page 10 Lamborghini Countach LP 500S Insert a 2 × 5mm self-tapping screw with Insert the tip of the screw into the end of Place the front fender (Stage 77) upside Tighten a 2.6 × 6mm screw (Stage 78) washer (Stage 78) through the hole at the bracket A and tighten into place.
- Page 11 Lamborghini Countach LP 500S Turn the front fender over while holding Tighten the screw into the hole, while Tighten a 2.6 × 5mm screw with washer Align the holes of door lock part B (Stage the left and right doors in place. Insert a holding the left door in place.
- Page 12 Lamborghini Countach LP 500S Place the main body assembly (Stage 77) as shown. Align Lower the front fender slightly, passing the door struts Lower the doors until the struts enter the slots in their front the two posts at the rear of front fender with the indicated through the holes in the rear of the fender (outlined).
- Page 13 Lamborghini Countach LP 500S Tighten another 2.6 × 6mm screw into Tighten a 2.6 × 6mm screw (Stage 78) Tighten another 2.6 × 6mm screw into Insert the larger post at the end of the the indicated hole in the right side into the hole in the tab at the bottom of the hole in the tab in the other side wiper (Stage 78) into the larger hole...
- Page 14 Lamborghini Countach LP 500S Align the holes in the bonnet hinges on Insert a 1.7 × 3mm screw into the hole Tighten the screw into the hole. Tighten another three 1.7 × 3mm screws the bonnet with the holes and pins at the indicated in the inset.
- Page 15 Lamborghini Countach LP 500S Stage 80 Completing Parts your model Right front fender Left front fender Right rear fender Left rear fender Number plate Number plate base 2 × 5mm self-tapping screws × 5 1.7 × 4mm countersunk screws × 2 1.7 ×...
- Page 16 Lamborghini Countach LP 500S Remove the battery box cover and insert three AAA Prepare interior light seals A and B (Stage 44). Peel seal A Place the combined seals into batteries into the box. Replace the cover and tighten the from the backing paper and place it over seal B, lining up the recessed centre of the screw back into place.
- Page 17 Lamborghini Countach LP 500S First, connect the battery box cable (red + black) and the This is how all the cables should now look. Make sure to Collect all of the cables together and secure them to the ignition key cylinder cable (orange + orange), coming from check that all of the cables match correctly and that the circuit board with masking tape, as shown above.
- Page 18 Lamborghini Countach LP 500S Hold the underbody above the main body and lower it slowly into place, aligning the points identified in Step 15. Fit the air duct hoses (circled) to the left and right air cleaners.
- Page 19 Lamborghini Countach LP 500S Combine the posts and holes at the sides of the model, as shown. Adjust the position of the radiators, fitting them into the recesses in the underbody. Check that the circled holes in the underbody are aligned with the holes in the posts on the main body.
- Page 20 Lamborghini Countach LP 500S Prepare 12 2.6 × 6mm screws (Stage 78), Half-tighten the screw into the hole. Half-tighten a second 2.6 × 6mm screw Half-tighten another 2.6 × 6mm screw then insert one of them into the hole into the hole in the opposite side of into the hole in the right front wheel arch.
- Page 21 Lamborghini Countach LP 500S Half-tighten another 2.6 × 6mm screw Half-tighten a 2.6 × 6mm screw into Insert a 2.6 × 6mm screw into this hole at Half-tighten the screw into place. into the indicated hole in the underbody. the hole on the other side of the the front of the underbody.
- Page 22 Lamborghini Countach LP 500S Tilt the grill towards you into a vertical Insert the tabs into the slots, and press Fit the holes in the number plate base Insert a 2 × 5mm self-tapping screw into position, and align the tabs with the slots the grill straight down onto the panel.
- Page 23 Lamborghini Countach LP 500S Tighten a second 1.4 × 3mm self-tapping Remove the rear axle from the right rear Remove the brake disc from one of the Place the brake disc onto the right rear screw into the other hole. wheel hub.
- Page 24 Lamborghini Countach LP 500S Push the cap into the hole. The cap has a Remove the front axle from the left front Hold one of the front wheels so that the Hold the front wheel in place, and insert magnet inside it, which will hold it in hub and place the brake disc (Stages 36 ridge on the inside (circled) is aligned the axle into the hole in the centre.
- Page 25 Lamborghini Countach LP 500S Fit the left door sill (Stage 79) into place Align the four pins on the inside of the Push the left rear fender into place. Fit the Align the four pins on the inside of the in the same way as the right sill.
- Page 26 Lamborghini Countach LP 500S Tighten the screw into place. Tighten a second 2 × 5mm self- Extend the cover stay and align the hole Tighten a 1.7 × 4mm self-tapping screw tapping screw into the hole on the at the end of it with the hole in the right into the hole.
- Page 27 Lamborghini Countach LP 500S Operating the parts The headlamps The doors The covers To raise the headlamps, push the part of the To open the door, push up on the door lock (circled), The bonnet and rear compartment cover are opened headlamp link bar projecting from the underbody and then lift the door up.
- Page 28 Lamborghini Countach LP 500S...
Need help?
Do you have a question about the MODEL SPACE Lamborghini Countach LP 500S and is the answer not in the manual?
Questions and answers
How to operate the light and sound functions ?
To operate the light and sound functions of the Deagostini MODEL SPACE Lamborghini Countach LP 500S:
- Insert the key into the ignition switch on the steering column to start the engine sound.
- Pull the left steering column lever back to turn the lights on. Pull it back again to turn them off.
- Push the left steering column lever in to sound the horn.
This answer is automatically generated