Sealey SA356 Instructions

Item Part No. Description Item Part No.
01 SA356/01 Throttle Lever 21 SA356/21
02 SA356/02 Lever Pin 22 SA356/22
03 SA356/03 Motor Housing 23 SA356/23
04 SA356/04 O-RinG 24 SA356/24
05 SA356/05 Valve Stem 25 SA356/25
06 SA356/06 O-Ring 26 SA356/26
07 SA356/07 Valve Spring 27 SA356/27
08 SA356/08 Air Controller 28 SA356/28
09 SA356/09 O-Ring 29 SA356/29
10 SA356/10 O-Ring 30 SA356/30
11 SA356/11 Valve Screw 31 SA356/31
12 SA356/12 Lock Nut 32 SA356/32
13 SA356/13 O-Ring 33 SA356/33
14 SA356/14 Housing 34 SA356/34
15 SA356/15 O-Ring 35 SA356/35
16 SA356/16 Ball Bearing 36 SA356/36
17 SA356/17 Front End Plate 37 SA356/37
18 SA356/18 Spacer 38 SA356/38
19 SA356/19 Key 39 SA356/39
20 SA356/20 Rotor 40 SA356/40
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim.
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 757500
SA356
PARTS LIST
Description Item Part No. Description
Rotor BladE 41 SA356/41 Stopper
Cylinder 42 SA356/42 Stopper Spring
Rear End Plate 43 SA356/43 Roll Pin
Ball Bearing 44 SA356/44 Stopper Pin
O-Ring 45 SA356/45 Tension Spring
Motor Nut 46 SA356/46 Tension Arm
Handle 47 SA356/47 Counter Sink
Cap Screw 48 SA356/48 Idle Shaft
Handle Braket 49 SA356/49 Idle Pulley
Finger Plate 50 SA356/50 Collar
Adjust Screw 51 SA356/51 Ball Bearing
Wheel Cover 52 SA356/52 Lock Nut
Wheel Cover Lid 53 SA356/53 Shoe
Roll Pin 54 SA356/54 Silencer
Lock Nut 55 SA356/55 O-Ring
Washer 56 SA356/56 Air Deflector
Drive Pulley 57 SA356/57 Air Inlet
Dust Cover 58 SA356/58 Grinding Belt
Cover Latch
Cap Screw
E-mail: sales@sealey.co.uk
01284 703534
Web: www.sealey.co.uk
INSTRUCTIONS FOR
AIR OPERATED
30mm BELT
SANDER
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
p WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
p WARNING! Disconnect from air supply before changing accessories or servicing.
Maintain the sander in good condition (use an authorised service agent).
3
Replace or repair damaged parts. Use genuine parts only. unauthorised parts may be dangerous and
3
will invalidate the warranty.
Use in a suitable work area, free from unrelated materials. Ensure there is adequate lighting.
3
Before each use check abrasive belt for condition. If worn or damaged replace immediately.
3
Use only the correct size and type of belt with this sander.
3
Ensure there are no flammable or combustible materials near the work area.
3
p WARNING! Always wear approved eye or face and hand protection when operating the sander.
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Depending on the task, sander noise level may exceed 85dB in which case wear safety ear defenders.
3
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery, and contain and/or tie back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the sander. Never hold a workpiece by hand.
3
Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
3
Avoid unintentional starting.
3
p WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
3
that all connections are secure.
Prolonged exposure to vibration from this sander poses a health risk. It is the owner’s responsibility to correctly
3
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
DO NOT use the sander for a task it is not designed to perform.
7
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
7
p WARNING! DO NOT sand any materials containing asbestos.
DO NOT carry the sander by the hose, or yank the hose from the air supply.
7
DO NOT force, or apply heavy pressure to the sander, let the sander do the work.
7
DO NOT switch the sander on whilst the belt is in contact with the workpiece.
7
DO NOT get the sander wet or use in damp or wet locations.
7
DO NOT place attachments close to your face and do not point at other persons or animals.
7
DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating
7
medication.
DO NOT use sander where there are flammable liquids, solids or gases such as paint solvents and
7
including waste wiping or cleaning rags etc.
DO NOT carry the sander with your finger on the power lever.
7
DO NOT direct air from the air hose at yourself or others.
7
When not in use disconnect from air supply and store in a safe, dry, childproof location.
3
SA356
Model:
SA356 - 1 - 211004