Download
Share
Print this page
Milnor 48040F7 Series Installation And Service
  1. Manuals
  2. Brands
  3. Milnor Manuals
  4. Washer
  5. 48040F7 Series
  6. Installation and service

Milnor 48040F7 Series Installation And Service

Hide thumbs Also See for 48040F7 Series:

Advertisement

Quick Links

Download this manual
Published Manual Number/ECN: MPI4840FAE/2004036N
• Publishing System: TPAS
• Access date: 1/19/2004
• Document ECN's: Exact
Installation and Service—
48040F7x
PELLERIN MILNOR CORPORATION
POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

Advertisement

loading
Need help?

Need help?

Do you have a question about the 48040F7 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Milnor 48040F7 Series

Summary of Contents for Milnor 48040F7 Series

  • Page 1 Published Manual Number/ECN: MPI4840FAE/2004036N • Publishing System: TPAS • Access date: 1/19/2004 • Document ECN's: Exact Installation and Service— 48040F7x PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.
  • Page 2 “Troubleshooting” chapter or section. See the table of contents. Trademarks of Pellerin Milnor Corporation The following, some of which may be used in this manual, are trademarks of Pellerin Milnor Corporation: ®...
  • Page 3 48040Fxx Washer Extractor Installation BIIFLI01/20020730 Shipping Bolts and Brackets BMP020035/2002226V Avoiding Damage from Allied Remote Chemical Delivery Systems BIWUUI03/20030306 About the Forces Transmitted by Milnor Washer-Extractors BIWUUI02/20001108 Chapter 2: Service and Maintenance Service Connections BIIFUI01/20020911 Preventive Maintenance BIIFUM01/20030311 Fastener Torque Requirements...
  • Page 4 Table of Contents, cont. Page Description Document/ECN Tilt Wheel Assembly BMP020032/2002226V Section 4: Door Assemblies Hydraulic Schematic BMP020016/2002226V Hydraulic Door Installation BMP020014/2002226N Installation Standard Door BMP020020/2002226V Standard Door BMP020017/2002226V Section 5: Water, Steam & Drain Water & Steam Schematics BMP020043/2003316V Water Inlets - Non Tilt BMP020044/2002226V Water Inlets - Tilt...
  • Page 5 Chapter Installation...
  • Page 6 (owner/user) is responsible for understanding and ensuring the proper operation and maintenance of the machine. The owner/user must familiarize himself with the contents of all machine instruc- ® tion manuals. The owner/user should direct any questions about these instructions to a Milnor dealer or the Mil- ®...
  • Page 7 Ê H azards During Installation ELECTROCUTION HAZARD—Contact with high voltages can kill or seriously injure you. All electrical connections must be made by a competent electrician. EQUIPMENT DAMAGE HAZARD—Machine can be damaged if shipping re- straints are improperly utilized. These include various bolts, brackets, and safety stands (painted red), brake blocks and the vibration safety switch (tie wrapped).
  • Page 8 MULTIPLE HAZARDS—Failure to maintain machine in proper working order can result in fatal or serious injury to operators and/or damage to property. DO NOT permit operation under any of the following circumstances: Malfunctioning door interlock mechanism. Malfunctioning limit switches. Malfunctioning two hand inching. Any evidence of cylinder damage.
  • Page 9 Ê A dditional Hazards During Tilting Machine Maintenance CRUSH/SEVER HAZARD—Tilting mechanisms can crush or sever parts of your body caught in them. Install the safety stands before performing maintenance under a tilted ma- chine. NEVER test or operate (manually or automatically) any machine function with any portion of a person’s body under the tilted machine—even if the safety stands are installed.
  • Page 13 BMP020028/2002226V (Sheet 3 of 3) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Guards & Covers Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 15 BMP020115/2003444V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Safety Placard Placement Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 17 BMP020116/2003444V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Safety Placard Placement Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 19 BMP020125/2003444V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Safety Placard Placement Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 21 BMP020126/2003444V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Safety Placard Placement Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 24 Do not hesitate to file a claim with the carrier if the machine is damaged in any way during shipment. Milnor will be glad to assist you in filing your claim, but is not responsible for any shipping damage to the machine once it has been delivered to the carrier in good condition.
  • Page 25 It is occasionally possible to reduce the overall dimensions by removing piping or other special modifications. Consult Milnor for additional information. 2. Sufficient clearance must be provided for normal operation and maintenance procedures.
  • Page 26 $( $ 6hh GQcXUb 5hdbQSd_b 9^cdQ\\QdY_^ BTccX]V?a^RTSdaTb To protect against lateral creeping of the machine during operation (due to vibration), roughen the area of the floor where the grout will be applied. Anchor bolts are required. 1. With the machine near the final location, unbolt the shipping skids. Observing all precautions, lift the machine off its skids and lower the machine onto blocking.
  • Page 27 $( $ 6hh GQcXUb 5hdbQSd_b 9^cdQ\\QdY_^ Figure 4: The hold down weldment Cone-can weldment as shipped, locking the shell and mid frame together Cup weldment when setup for operation Figure 5: Shims stored under the mid frame @5<<5B9> =9<>?B 3?B@?B1D9?>...
  • Page 28 $( $ 6hh GQcXUb 5hdbQSd_b 9^cdQ\\QdY_^ 1TU^aTCX[cX]V<PRWX]T —Tilting mechanisms can crush or sever parts of your F0A=8=6 $ ) 2adbWBTeTa WPiPaS body caught in them. • Install safety stands before performing maintenance under a tilted machine. • NEVER test or operate (manually or automatically) any machine function with any portion of a person's body under the tilted machine - even if the safety stands are installed.
  • Page 30 BMP020035/2002226V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Shipping Bolts and Brackets Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 31 ® of such systems by the chemical supply company. Milnor washer-extractors and CBW batch washers (tunnels) are available with convenient inlets for such systems (see Figure 1). Most common of the types of systems currently used in commercial laundering operations are pumped chemical systems.
  • Page 32 CAUTION 1 : Equipment and Textile Damage Hazards—Chemicals leaked into the machine, particularly when it is idle can destroy machine components and textiles left in the machine. Pellerin Milnor Corporation accepts absolutely no responsibility for damage to its equipment or to textiles therein from abnormal contact with chemicals.
  • Page 33 Hence, any concentrated chemical that remains in the injection line between the pump and the machine is free to flow into the machine. Some examples of this are shown in Figure 3. PELLERIN MILNOR CORPORATION...
  • Page 34 PELLERIN MILNOR CORPORATION...
  • Page 35 CAUTION 2 : Injury and Damage Hazards—Chemicals leaking from a chemical system may be corrosive or toxic. Such chemicals can injure personnel and damage equipment. • Use care when connecting chemical lines. • Inspect regularly for leaks. — End of BIWUUI03 — PELLERIN MILNOR CORPORATION...
  • Page 36 • the liquor level and chemical conditions in the bath preceding extraction, and • other miscellaneous factors. ® Estimates of the maximum force normally encountered are available for each Milnor model ® and size upon request. Floor or foundation sizes shown on any Milnor...
  • Page 37 All data is subject to change without notice and may have changed since last printed. It is the sole responsibility of every potential owner to obtain ® written confirmation that any data furnished by Milnor applies for the model(s) and serial number(s) of the specific machines.
  • Page 39 Chapter Service and Maintenance...
  • Page 40 CUbfYSU 3_^^USdY_^c 2996E9 ! @eR\YcXUT 2__[ c`USc 4QdUc* " " )!!  " " )!!  " " )!! <Q^W* 5>7 ! 1``\YS* 96< BTaeXRT2^]]TRcX^]b Required service connections (depending on the machine model and optional equipment) are as follows: 1. Piped inlets and outlets are as listed in the “Table of Piped Inlets” and “Table of Piped Outlets.”...
  • Page 41 CUbfYSU 3_^^USdY_^c Table 2: Table of Piped Inlets Description of Source Requirements Piping Specifications, Connections Comments Cold water inlet 1-1/2" NPT 10 - 75 PSI (0.7 -5.27 Pipe material per plumbing code kgs.sq. cm.) Hot water inlet Steam inlet 1 - 1/4" NPT 30 - 115 PSI (2.10 - Pipe material per plumbing code 8.08 kgs.
  • Page 42 CUbfYSU 3_^^USdY_^c • Any such conditions should be corrected prior to commissioning your machines. Figure 1: Rotation Direction during Drain and Extract 4[TRcaXR?^fTa2^]]TRcX^]b —The customer must furnish a remotely mounted switch !" with lag type fuses, circuit breakers and wiring between the electrical service box and the junction box on the machine.
  • Page 43 # #!!  " # #!! <Q^W* 5>7 ! 1``\YS* 96< ?aTeT]cXeT<PX]cT]P]RT As required by the warranty and to achieve optimum performance and service life from Milnor washer-extractors, the schedules, instructions and precautions herein must be strictly followed. F0A=8=6 ) 4]cP]V[T P]S 2adbW 7PiPaSb —Guards, covers, and panels—Operating the...
  • Page 44 If you cannot obtain either the specified lubricant or a valid equivalent locally, contact the Milnor Service Department for assistance. <PX]1TPaX]V7^dbX]V?aTeT]cXeT<PX]cT]P]RT F0A=8=6 $ ) 4]cP]V[T P]S 2adbW 7PiPaSb —Guards, covers, and panels—Operating the...
  • Page 45 @bUfU^dYfU =QY^dU^Q^SU ?aTeT]cXeT<PX]cT]P]RT " Table 1: Preventive Maintenance Checklist Components Action Frequency Specifications/References/Figures Main Bearing Bearings Slowly grease: 5 strokes - Monthly Shell Alvania EP (or equivalent). Housing 0.30 ounces (8.85 grams) at See "48040Fxx Bearing Housing two locations Maintenance Points" Seals Slowly grease, 2 strokes - 0.12 ounces (3.54 grams) at...
  • Page 46 @bUfU^dYfU =QY^dU^Q^SU » Fit string to the outer diameter of both pulleys and slowly raise motor platform until string is tight. » After 24 hours of operation, remove tension from the belt and measure the outer diameter again, then see L2 in the “Banded Belt Final Tension” section of the Final Drive Belt Tension table.
  • Page 47 @bUfU^dYfU =QY^dU^Q^SU Table 2: 48040Fxx Final Drive Tension Banded belt initial tension Banded belt final tension Tensioned length Tensioned length L1 (inches) Multiplier L2 (inches) Multiplier (inches) (inches) 1.003 149.4 1.005 149.7 149.2 149.6 149.2 149.9 149.4 149.8 149.4 150.1 149.6 149.6 150.3...
  • Page 48 @bUfU^dYfU =QY^dU^Q^SU manufacturer of the equipment. If you do not wish to do this, we suggest that when you replace the belts, you purchase the exact style and type belts with which the machine was originally equipped. This is the best way to achieve belt life on your replacement belts equal to the life of the original set.
  • Page 49 @bUfU^dYfU =QY^dU^Q^SU Figure 2: 48040Fxx Door Hinge Figure 3: Staph-Guard Isolator Fastener Grease Point Figure 4: 48040Fxx Springs Figure 5: 48040Fxx Steam Strainer Location (Tilt machine shown) @5<<5B9> =9<>?B 3?B@?B1D9?>...
  • Page 50 @bUfU^dYfU =QY^dU^Q^SU Figure 6: Tilting Machine Components Tilting system air pressure Tilt wheel grease fittings (8 locations) Legend 50 psi (6.9 kg. sq. cm.) Tilt wheel grease points (8 locations) Figure 7: 48040Fxx Inverter Maintenance Points 48040Fxx Inverter Legend Vents Fans —...
  • Page 51 The specifications in this section apply to 1/4 inch and larger Unified National fine and coarse fasteners used on ® Milnor machines. This information is to be used only when torque specifications are not stated in the installation or service instructions.
  • Page 52 MSSM0101CE/9906AV (2 of 19) Ê A pplying Threadlocker NOTE: The following threadlocker information and ® illustrations are excerpts from the Loctite User’s Guide and are used with permission. For maximum strength, threadlocker must fill the thread voids completely, as shown in FIGURE 2. Organic or petro- leum solvent will remove excess uncured adhesive from joints.
  • Page 53 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (3 of 19) Ë R emoving Fasteners ® High strength threadlockers like Loctite 271 (or equivalent) may be weakened by heating to at least 500 F (260 C) as follows. 1. Apply localized heat to fastener as shown in FIGURE 5. 2.
  • Page 54 MSSM0101CE/9906AV (4 of 19) Ï A ll values in foot pounds and (Newton meters) Nomi- Grade Designation Zinc or If instructions call for : nal bolt and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare size Plated 222 or 1/4 - 28 SAE Grade 1 ASTM A307 (3.80)
  • Page 55 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (5 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc If instructions call for : bolt size and Standard orCadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 5/16 - 24 SAE Grade 1 10.4 ASTM A307...
  • Page 56 MSSM0101CE/9906AV (6 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for : bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 3/8 - 24 SAE Grade 1 10.2 12.2...
  • Page 57 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (7 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Zinc or If instructions call for : bolt size Designation and Cadmium Loctite Loctite Loctite Loctite Loctite Bare Standard Plated 222 or 7/16 - 20 SAE Grade 1 16.0 19.2...
  • Page 58 MSSM0101CE/9906AV (8 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Standard and Zinc or If instructions call for : bolt size Grade Designation Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 1/2 - 20 SAE Grade 1 24.8 29.8...
  • Page 59 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (9 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for: bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 9/16 - 18 SAE Grade 1 35.3 42.4...
  • Page 60 MSSM0101CE/9906AV (10 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for: bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 5/8 - 18 SAE Grade 1 49.5 59.4...
  • Page 61 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (11 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for: bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 3/4 - 16 SAE Grade 1 86.5...
  • Page 62 MSSM0101CE/9906AV (12 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for: bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 7/8 - 14 SAE Grade 1 137.8 165.4...
  • Page 63 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (13 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Zinc or If instructions call for : bolt size Designation and Cadmium Loctite Loctite Loctite Loctite Loctite Bare Standard Plated 222 or 1 - 12 SAE Grade 1 205.3...
  • Page 64 MSSM0101CE/9906AV (14 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for : bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 1-1/8 • 7 SAE Grade 1 265.8 318.9 354.4...
  • Page 65 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (15 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Zinc or If instructions call for : bolt size Designation and Cadmium Loctite Loctite Loctite Loctite Loctite Bare Standard Plated 222 or 1-1/4 •...
  • Page 66 MSSM0101CE/9906AV (16 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for : bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 1-3/8 • 6 SAE Grade 1 491.1 589.4 654.8...
  • Page 67 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (17 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Zinc or If instructions call for : bolt size Designation and Cadmium Loctite Loctite Loctite Loctite Loctite Bare Standard Plated 222 or 1-1/2 •...
  • Page 68 MSSM0101CE/9906AV (18 of 19) Ï O ther Fastener Torque Specifications Ï A ll values in foot-pounds and (Newton-meters) Nominal bolt size 18 - 8 Brass Aluminum Stainless Steel Stainless Steel 2024 - T4 1/4 - 20 6.3 (8.54) 6.6 (8.95) 5.1 (6.91) 3.8 (5.15) 1/4 - 28...
  • Page 69 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (19 of 19) Ï O ther Fastener Torque Specifications Ï A ll values in foot-pounds and (Newton-meters) Nominal bolt size 18 - 8 Brass Aluminum Stainless Steel Stainless Steel 2024 - T4 7/8 - 9 194.0 (263.03) 202.5 (274.55) 158.8 (215.30) 124.6 (168.93)
  • Page 70 CUbfYSY^W 4YcS 2bQ[Uc 295EE= ! @eR\YcXUT 2__[ c`USc 4QdUc* " # !"#  " # !"#  " # !"# <Q^W* 5>7 ! 1``\YS* 5EE BTaeXRX]V3XbR1aPZTb Disc brakes require three different levels of service; brake inspection as specified in the preventive maintenance schedule, puck replacement, and complete caliper overhaul.
  • Page 71 CUbfYSY^W 4YcS 2bQ[Uc 6. Mount new pucks on piston. Tighten screws, ensuring screw heads are completely recessed into pucks. 7. Reassemble brake assembly. Tighten mounting bolts to 30 foot-pounds (41 Newton-meters). 8. If the calipers were overhauled, then see “Bleeding the Brake Circuit” below. Otherwise, return machine to service.
  • Page 72 CUbfYSY^W 4YcS 2bQ[Uc • Wear eye protection during procedure. • Follow procedure carefully to avoid possible injury. 2. Attach one end of the flexible hose to one of the top bleed valve. Place the other end of the hose into a bottle or jar containing 1/2 - 1 inches (12.7 - 25.4) of clean brake fluid. Submerge the hose below the fluid surface to prevent sucking air on the return stroke.
  • Page 73 Chapter Section Drive Assemblies...
  • Page 75 BMP020010/2002226V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Drive Chart Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 78 BMP020021/2002226V (Sheet 3 of 3) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Motor Mount Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 80 BMP020039/2002226V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Cylinder Installation Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 86 BMP020013/2003444V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Bearing Air Inject Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 90 BMP020038/2002226V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Air Cylinder Brake Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 91 Chapter Section Suspension...
  • Page 97 Chapter Section Tilt Assemblies...
  • Page 100 BMP020023/2002226V (Sheet 3 of 3) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Frame & Pivots Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 102 BMP020027/2002226V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Air Tilt Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 105 Chapter Section Door Assemblies...
  • Page 117 Chapter Section Water, Steam & Drain...
  • Page 119 BMP020043/2003316V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Water & Steam Schematics Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 121 BMP020044/2002226V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Water Inlets Non Tilt Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 128 BMP800228/2002226V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List, cont.—3 & 4 Inch Dump Valve Assembly Description Comments Used In Item Part Number 02 16021I 94191# DUMPVAL STEM-4"+8" DYE 316L X2 02743 87382B BONNET=2"DUMP VALVE...
  • Page 131 BMP020049/2002226V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Float Chamber Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 133 Chapter Section Chemical Supply Assemblies...
  • Page 136 BMP020040/2002226V (Sheet 3 of 3) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Soap Chute Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 139 Chapter Section Pneumatic Assemblies...
  • Page 141 BMP020015/2002226V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Pneumatic Schematic Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 143 Chapter Dimensional Drawings...