Table of Contents
Advertisement
Quick Links
25-135H
13" Portable Planer
with Helical-Style Cutterhead
Operator's Manual
Record the serial number and date of purchase in your manual for future reference.
The serial number can be found on the specification label on the rear of your machine.
Serial Number: _________________________
Date of purchase: _________________________
For technical support, email techsupport@rikontools.com - For parts questions, email parts@rikontools.com
www.rikontools.com
25-130HM3
Advertisement
Table of Contents
Related Manuals for Rikon Power Tools 25-135H
Summary of Contents for Rikon Power Tools 25-135H
-
Page 1: Maximum Depth Of Cut
25-135H 13” Portable Planer with Helical-Style Cutterhead Operator’s Manual Record the serial number and date of purchase in your manual for future reference. The serial number can be found on the specification label on the rear of your machine. Serial Number: _________________________ Date of purchase: _________________________ For technical support, email techsupport@rikontools.com - For parts questions, email parts@rikontools.com... -
Page 2: Table Of Contents
Troubleshooting ......................17 Parts Diagrams & Parts Lists ..................18 - 21 Accessories ......................22 Notes ..........................22 Warranty ..........................23 SPECIFICATIONS - 25-135H Motor ................120V, 60Hz, 15A, PH1, AC Motor Speed (no load)................ 22,000 RPM Cutterhead Diameter ..................2 ” Cutterhead Speed ................10,000 RPM Number of HSS Inserts, 2-sided................ -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. There are certain applications for which this tool was designed. -
Page 4: Dust Port (O.d.)
SAFETY INSTRUCTIONS 12. KEEP PROTECTIVE GUARDS IN PLACE AND IN 25. ALWAYS WEAR A DUST MASK TO PREVENT WORKING ORDER. INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust 13. AVOID ACCIDENTAL STARTING. Make sure that and asbestos dust. Direct particles away from face and the power switch is in the “OFF”... -
Page 5: Electricals & Wiring Diagram
SAFETY INSTRUCTIONS EXTENSION CORDS ELECTRICAL SAFETY THE USE OF AN EXTENSION CORD THIS TOOL MUST BE GROUNDED WITH THIS MACHINE IS NOT RECOMMENDED. For WHILE IN USE TO PROTECT THE OPERATOR FROM best power and safety, plug the machine directly into a ELECTRIC SHOCK. -
Page 6: Number Of Cutterhead Insert Rows
SAFETY INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR PLANERS This machine is intended for the surfacing of natural, solid woods. The permissible workpiece dimensions must be observed (see Technical Specifications). Any other use not as specified, including modification of the machine or use of parts not tested and approved by the equipment manufacturer, can cause unforeseen damage and invalidate the warranty. -
Page 7: Getting To Know Your Machine
PARTS DIAGRAMS AND PARTS LISTS CONTENTS OF PACKAGE Model 25-135H 13” Portable Planer is shipped complete in one box. UNPACKING AND CLEAN-UP 1. Carefully remove all contents from the shipping carton. Compare the contents with the list of contents to make sure that all of the items are accounted for, before discarding any packing material. -
Page 8: Installation
THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ASSEMBLY IS COMPLETE. NOTE: The 25-135H Planer requires minimal TOOLS REQUIRED FOR ASSEMBLY assembly, and therefore the machine can be mounted... -
Page 9: Assembly
ASSEMBLY INSTALLING THE HANDWHEEL KNOB for Height Setting of the Thickness Table 1. Locate the Handle Screw and Height Adjustment Handwheel. 2. Place the Height Adjustment Handwheel onto the shaft at top corner of the Planer. 3. Tighen the Handle Screw with the supplied 4mm hex wrench. FIG. 1. FIG. -
Page 10: Adjustments
ADJUSTMENTS LEVELING THE TABLE EXTENSIONS 1. The infeed and outfeed table extensions are attached to the planer. Shipped in a folded, upright position, the table extensions must be in the down position before planing can begin. For accurate planing, the table extensions must be level with the planer table. - Page 11 ADJUSTMENTS REPLANING LOCK using the REPEAT CUT 1. Remove the screws to take off the height adjustment hand- wheel (1 screw), remove the right side panel (3 screws) and top cover (4 screws). FIG. 5. STEP 2. Lower the cutterhead STOP BLOCK assembly until the stop screw...
-
Page 12: Operation
OPERATION PLANING • Thickness planers work best if at least one side of the workpiece has a flat surface. When both sides of a • workpiece are rough, use a surface planer or jointer first to define the initial flat surface. Plane one side of the workpiece then flip the workpiece and plane the surface of the reverse side. -
Page 13: Maximum Cutting Width
OPERATION POWER SWITCH The planer is turned on by flipping the switch into the up position and it is turned off by flipping the switch in the down position. This planer is also equipped with a special lockout toggle switch that prevents unauthorized use. -
Page 14: Maintenance
MAINTENANCE THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ADJUSTMENTS ARE COMPLETE. ROTATING OR REPLACING KNIFE INSERTS This machine has a cutterhead with 6 rows of High Speed Steel knife inserts. Each of the 26 inserts on the cutterhead are indexed and have two sharpened sides. - Page 15 MAINTENANCE POSITIONING SHARP EDGE (S) FLAT STAR EDGE SCREW INDICATOR ROTATE INSERT TO INSTALL A MARK FIG. 11 NEW SHARPENED EDGE THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ADJUSTMENTS ARE COMPLETE. BRUSH REPLACEMENT Brush life will vary depending on the load placed on the motor.
-
Page 16: Two Feed Speeds Sf/Min
MAINTENANCE Turn the power switch “OFF” and disconnect the plug from the outlet prior to adjusting or maintaining the machine. DO NOT attempt to repair or maintain the electrical components of the motor. Contact a qualified service technician for this type of maintenance. 5. -
Page 17: Troubleshooting
TROUBLESHOOTING FOR YOUR OWN SAFETY, ALWAYS TURN OFF AND UNPLUG THE MACHINE BEFORE CARRYING OUT ANY TROUBLESHOOTING. SYMPTOM POSSIBLE CAUSES SOLUTIONS Planer will not start. 1. No power 1. Check power source, plug and wiring. 2. Blown shop fuse 2. Check fuse, replace if it is blown. 3. -
Page 18: Parts Diagrams & Parts Lists
PARTS DIAGRAM... - Page 19 PARTS LIST KEY NO. KEY NO. DESCRIPTION PART NO. DESCRIPTION PART NO. TOP COVER P25-135H-1 SCREW HEX HD M8xP1.25x20L P25-135H-55 ROLLER TUBE P25-135H-1A GEAR (INTERMEDIATE) P25-135H-56 SUPPORT P25-135H-1B RING RETAINING EXT P25-135H-57 ROLLER P25-135H-1C GEAR SPINDLE P25-135H-58 SPECIAL WASHER P25-135H-1D RING RETAINING EXT P25-135H-59 SCREW M4xP0.7x8L...
- Page 20 PARTS DIAGRAM...
- Page 21 PARTS LIST...
-
Page 22: Accessories
2 pre-sharpened edges ADDITIONAL PLANER ACCESSORIES For addtional accessories for use with the 25-135H thickness planer, contact your local RIKON distributor, or visit the RIKON website at www.rikontools.com. There you will find Dust Collectors, Dust Hose, Stands, Mobile Bases and other parts and accessories for the RIKON machinery in your shop. -
Page 23: Warranty
® 5-Year Limited Warranty RIKON Power Tools Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship for a period of five (5) years from the date the product was purchased at retail. This warranty may not be transferred. - Page 24 25-135H For more information: 16 Progress Road Billerica, MA 01821 877-884-5167 / 978-528-5380 techsupport@rikontools.com Link to RIKON Website www.rikontools.com 25-135HM1...
Need help?
Do you have a question about the 25-135H and is the answer not in the manual?
Questions and answers