Table of Contents
Advertisement
Available languages
Available languages
Problems
Signals
®
EASY PRESS
POWER
will not turn on
STATUS
POWER
STATUS
POWER
STATUS
POWER
STATUS
The pump will
not start when
a tap is turned on
POWER
STATUS
POWER
STATUS
The pump
POWER
delivers no or low
STATUS
pressure
The pump stops
POWER
and starts
STATUS
repeatedly
The pump will
POWER
not stop
STATUS
= Off
= On
Exploded view of spare parts
Attention: when ordering spare
parts, always state the position
n° from the diagram below and
the product code number found
in the pressure-flow regulator
technical data table.
1 - Circuit board cover
2 - Pressure gauge
CODE:
V / Hz:
3 - Circuit board
I max:
4 - Cable bushings
P start:
5 - Valve unit
Year:
Disposal
When disposing of any EASY
PRESS
®
parts, adhere to the
relevant laws and regulations
in force in the country in
which the equipment is
being used.
Do not dispose
of any polluting
parts in the
environment.
Possible causes
No power
EASY PRESS
quate start-up pressure (Pm) for the
chosen application.
Faulty electrical connections or
pump out of service
EASY PRESS
EASY PRESS
down due to "DRY RUNNING" due to
lack of water
Maximum pump pressure is
insufficient
EASY PRESS
down due to "FREQUENT START-UP"
Filters or pipes may be partly blocked Check the water pipes
EASY PRESS
completely
Leaks within the system (less than
the shut-off flow rate Qa)
POWER
STATUS
The flow rate is higher than the
shut-off flow rate (Qa)
EASY PRESS
close
2
3
1
Article
50066/115
~230 / 50-60
16 A
1.5 Bar
Version
B
2008
Statement of Compliance: we declare, under our own responsibi-
lity, that the product in question is in compliance with the following
European Directives and national implementation provisions
2006/95/CEE Low Voltage Directive
2002/95/CEE (RoHS)
2002/96/CEE - 2003/108/CEE (WEEE)
2004/108/CE Electromagnetic Compa-
tibility Directive (EMC)
EN 60730-2-6
EN 61000 6-3
®
model with an inade-
®
"OUT OF SERVICE"
®
in temporary shut
®
in temporary shut
®
's valve will not open
®
's check valve will not
= Flashing
4
5
San Bonifacio 06.06.12
PEDROLLO SpA
Director
Silvano Pedrollo
Solutions
Check the electrical connections
®
Relocate EASY PRESS
to another position
Install a model with a higher start-up pressure (Pm)
Check the electrical connections and that the pump
is working
®
Reset EASY PRESS
(See Operation, point 3).
Wait for the automatic restart or press START to
restart manually (See Operation, point 4a)
Replace the pump with one with more suitable
characteristics
Install a model with a lower start-up pressure (Pm)
Wait for the automatic restart or press START to
restart manually (See Operation, point 4b). Remove
any cause of leakage from system or install an
expansion tank
Check that the valve is not blocked by any foreign
objects and clean if necessary
Check the hydraulic connections and repair any
leaks. If a leak cannot be repaired, install an
expansion tank
Make sure that all taps are turned off and that
there are no leaks within the system
Check that the valve is not blocked by any foreign
objects and clean if necessary
Size
221
M 1"
M 1"
Made in Italy by
SpA
Via Enrico Fermi, 7
37047 San Bonifacio (Verona) ITALY
Tel +39 045 6136311
Fax +39 045 7614663
sales@pedrollo.com
www.pedrollo.com
= Flashing
174
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the EASYPRESS and is the answer not in the manual?
Questions and answers
Hi, when my easy press runs dry, it takes more than 10 hours to restart even though I can hear and see plenty of water in the tank, it just sits on dry or frequent start up. I follow your instructions but its very random
The PEDROLLO EASYPRESS takes more than 10 hours to restart when it runs dry because it performs automatic restart attempts at increasing time intervals. After detecting a dry run condition, it stops the pump and initiates retry attempts at intervals of 15, 30, 60 minutes, and then every hour. This gradual process can extend the restart time beyond 10 hours, even if water is available in the tank.
This answer is automatically generated
Hello. My easy press is now 15 years of service, but now is taking a long time to shut down the pump. The pressure is too high, and takes 10 seconds to shut down after all the taps are turned off. Does it need a change for a new easy press? Does the service /functioning deteriorate after 15 years good service.?
Can we adjust the pressure in easy press 2 pressure switch?
The PEDROLLO EASYPRESS pressure switch operates by turning the pump on and off based on system pressure and flow. The document mentions that different models have different operating pressures, and if the installed model is not suitable for the installation type, a model with a higher operating pressure (Pm) should be used. However, it does not explicitly mention that the pressure can be manually adjusted. Instead, selecting the appropriate model with the required pressure rating is recommended.
This answer is automatically generated
My easy press is giving an error message that it experiencing dry run and switching off although water supply if full and valves to the water supply are open
The PEDROLLO EASYPRESS may show a dry run error and turn off despite a full water supply and open valves due to one or more of the following reasons:
1. Blocked Pipes or Filters – If the water pipes or filters are partially blocked, the system may not detect sufficient flow, triggering the dry run protection.
2. Faulty or Blocked Check Valve – If the EASY PRESS® check valve is blocked or fails to open properly, water flow may be restricted, causing the system to stop the pump.
3. Leaks in the System – Small leaks in the hydraulic connections can reduce pressure below the required level, leading to the dry run error.
4. Incorrect Installation – If a non-return valve is installed between the pump and EASY PRESS®, or if air is trapped in the system, the device may not detect water properly.
Checking and cleaning the pipes, filters, and valves, as well as ensuring proper installation and sealing leaks, may resolve the issue.
This answer is automatically generated