Advertisement
Quick Links
Advertisement
Related Manuals for MERLYN IQ Nexa
Summary of Contents for MERLYN IQ Nexa
- Page 1 BIFOLD DOOR Bifold door with Side Panel Bifold door in recess Pages 8~16 Pages 1~7 PATENT PENDING...
- Page 2 Wall screw 4x30 Wall plug Wall screw Wall screw cover cap cover clip ×6 ×6 ×6 ×6 2SY51 2SP12 2SS008 2SS009 Handle Locking cap Cover cap Wedge seal of pivot ×2 K019/K040 K021/K022 K024 x 1 K142...
- Page 3 K021/K022 2SS008 K019/K040 K024 K206 2SP12 2SY51 K095 K155 K142 K205 2SS009...
- Page 4 Please ensure your tray is 100% level in all directions before fitting your enclosure. 100%level!
- Page 5 Measure X to make sure it is within the adjustment range Size 650-690 710-750 750-790 850-890 1000 950-990 K095...
- Page 6 A. Fit the wall profile onto the frame and lift the frame onto the tray. B. Fix the frame to the wall using 4 x 30 screws and the cover cap clips. C. Finally fit the caps over the clips. 2SS009 2SS009 2SS008...
- Page 7 Push the wedge seals between the bottom profile and the tray to hold the frame in position. K142 K142 K024...
- Page 8 K021/K022 K021/K022 Before sealing make sure all surfaces are clean, dry and free from any residue such as grout. Use a quality silicone sealant and applicator gun to finish the door. Seal between the wall and the wall profile. Seal between the wall profile and the frame 50mm from the tray. Seal across the top of the locking cap between the cap and the wall.
- Page 9 Wall screw Wall plug Installation tool ×3 ×3 K023 ×1 Cover cap of corner Cover cap of corner Cover cap of side post for Pivot and Bifold post for slider panel wall profile K013/K014 K016/K017 K015×1...
- Page 10 K079 K183 K165 K077 K015 K016/K017...
- Page 12 A. Mark a line to set the outside position of the wall profile. 10mm from the edge of the tray is recommended and must be within the adjustment X of the door size shown in the table below. Measure X to make sure it is within the adjustment range size 662-682...
- Page 13 A. Slide the panel into the wall profile. Max adjustment is 20mm. B. Make sure the screws on the edge of the frame are facing to the inside. Max.20mm Min.10mm A. Slide the frame into the wall profile. B. Insert a screwdriver through the slot on the outside edge of the profile and remove the three cover caps.
- Page 14 A. Fully open the door. B&C. Lift the door frame until the bottom holes are aligned with the screws in the side panel. D&E. Bring the frames together then lower the door frame and tighten the 3 screws through the slot in the side of the frame. A.
- Page 15 A. Adjust the door frame side to side until the side panel is parallel to the side of the tray and the frame is square and the door is sliding freely. B. Slide the locking cap into position. K019/K040 A. Push the wedge seals between the bottom profile and the tray to hold the frame in position.
- Page 16 K024 K015 K021/K022 K016/K017...
- Page 17 Before sealing make sure all surfaces are clean, dry and free from any residue such as grout. Use a quality silicone sealant and applicator gun to finish the door. Seal between the wall and the wall profile. Seal between the wall profile and the frame 50mm from the tray. Seal across the top of the locking cap between the cap and the wall.
Need help?
Do you have a question about the IQ Nexa and is the answer not in the manual?
Questions and answers