Sealey FJ48 Instructions

Your new Jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE
THIS JACK CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
1. SAFETY PRECAUTIONS
1.1. GENERAL SAFETY
3 Visually and operationally inspect Jack before each use, ensure it is sound. Take action for immediate repair or replacement of
damaged parts. Use genuine parts only. The use of improper parts may be dangerous and will invalidate the warranty.
p WARNING! If any part of Jack fails to work properly, discontinue and have repaired. Never attempt to repair Jack while Jack is under load.
p WARNING! Ensure Jack to supported on suitable base so it will not slip or shift during operations and load is properly supported at lift
point to prevent shifting. If required, use appropriately rated clivis pins, chains, bolts, ropes etc, through beam holes to assist operation.
3 Place complete lifting beak of jack under object to be lifted. You can pull lifting beak up to the point of lift (or strain) without pumping handle.
3 Always lock and/or stabilise load to be lifted. The Jack will not act as a load stabiliser.
3 Always keep firm grip on pumping handle and support beam.
3 All persons shall be clear of load being raised, lowered or pulled. Never work under a raised load unless using additional supports
and insert 1/2” bolt (not included) through hole in steel beam immediately below lifting mechanism, (to act as a safety pin).
p WARNING! if you exceed rated capacity at the height of one foot, the shear pin will break and the handle will drop.
3 Jack must have a 50kg load or more to activate the lowering step by step, otherwise lifting beak will drop.
3 Ensure there are no persons or obstructions beneath a load before lowering.
s DANGER! DO NOT use additional devices on handle to provide extra leverage. Use hand power only.
7 DO NOT operate the jack if damaged.
7 DO NOT exceed the rated capacity of the jack.
p WARNING! DO NOT place an excessive strain on load, equipment or supports when using jack for pulling or tensioning.
7 DO NOT push lifted load off Jack.
s DANGER! DO NOT use the jack for purpose other than for which it is designed.
3 Put handle in upright position before tripping the reversing latch to lower load.
3 KEEP JACK CLEAN AND OILED. Front and back of rail must be kept rust free. Store in a safe, dry childproof area.
1.2. WHEN USED TO JACK A VEHICLE
O IMPORTANT: Apply appropriate safety features as mentioned in 1.1. above with the following additions or exceptions:
3 Place wedges under wheels of vehicle.
3 Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PARK” if automatic).
3 Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc.,
to allow for vehicle tilting.
3 Ensure there are no passengers in the vehicle.
3 Only place jack under those lifting points recommended by vehicle manufacturer (see vehicle hand book).
3 Check the lifting point is stable and correctly positioned on the lifting beak.
p DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
3 Use suitable capacity axle stands under the vehicle before proceeding with any task.
3 Ensure there are no persons or obstructions beneath the vehicle before lowering.
7 DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
7 DO NOT work under the vehicle until axle stands have been correctly positioned.
7 DO NOT allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
2. INTRODUCTION & SPECIFICATIONS
Heavy-duty lever-ratchet operated jack with 48" beam. Reversible
ratchet mechanism enables jack to be used for lifting or lowering.
Versatile and lightweight unit suitable for pulling tree-stumps and
tensioning fences as well as a positioning aid for heavy machinery.
Many units sold to 4WD owners
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
I N S T R U C T I O N S F O R :
FARM JACK
MODEL:
Specifications
Max Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000kg
Min height . . . . . . . . . . . . . . . . . . . . . . . . . . . .150mm
Max. height . . . . . . . . . . . . . . . . . . . . . . . . . .1200mm
Min lowering load . . . . . . . . . . . . . . . . . . . . . . . . .50kg
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.6kg
01284 703534
01284 757500
FJ48
E-mail: sales@sealey.co.uk
FJ48 - 0016 - (1) - 150600