Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Chauvet Q-Spot
Summary of Contents for Chauvet Q-Spot
- Page 1 Q-Spot™ 250W EHJ Intelligent Moving Yoke Q-Spot™ 150 150W HTI Intelligent Moving Yoke USER MANUAL CHAUVET, 3000 N 29 Ct, Hollywood, FL 33020 U.S.A (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.com 2005-11-15/13:11...
-
Page 2: Table Of Contents
Fixture Linking ... 15 DMX C (16 B ) ... 16 HANNEL ALUES ... 17 AINTENANCE ... 17 ETURNS ROCEDURE ... 17 LAIMS ... 18 ENERAL ROUBLESHOOTING ... 19 ECHNICAL PECIFICATIONS Q-Spot & Q-Spot 150 User Manual ) ... 10 2005-11-15/13:11... -
Page 3: Before You Begin
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact CHAUVET. Q-Spot & Q-Spot 150 User Manual Power cord with plug ... -
Page 4: Introduction
150 watts. This color is considered true white, also known as daylight. The Q-Spot™ uses the ever popular EHJ halogen lamp. It is a powerful and economical lamp. At 250 watts it provides just over of the same intensity measured in lumens as the HTI® 150 though at the expense of shorter life. -
Page 5: Dmx Channel Summary
Setting = HANNEL Pan (Fine) Pan/Tilt Speed Setting = HANNEL Pan (Fine) Pan/Tilt Speed Setting = HANNEL Pan/Tilt Speed Shutter/Dimmer Q-Spot & Q-Spot 150 User Manual UNCTION HANNEL Tilt UNCTION HANNEL Tilt Tilt (Fine) UNCTION HANNEL Tilt Tilt (Fine) -
Page 6: Product Overview
Down functions Steps forward through menu functions Confirms selected menu Enter function Q-Spot & Q-Spot 150 User Manual SEGMENT BUTTONS I/O PANEL OVERVIEW I/O P ANEL DMX Out & In DMX-512 connectors Power AC input IEC 60320 C14 and fuse holder Introduction 1. -
Page 7: Setup
To ensure the longest and most efficient use of the lamp always wait between 10 and 15 minutes before re-applying power after a shutdown. Failure to do so could result in premature aging of the lamp and failure to the electronics that drive it. Q-Spot & Q-Spot 150 User Manual 2005-11-15/13:11... -
Page 8: Power
1. Press both tips of the gobo tension ring together and remove from aperture. 2. Push the gobo with your finger from the back side following the same direction that the tension ring was removed. Q-Spot & Q-Spot 150 User Manual NTERNATIONAL Live... -
Page 9: Mounting
3. From a stable platform, attach a clamp to the bracket. Depending on your particular clamp, it may be necessary to attach clamp to bracket before mounting bracket to plate. Q-Spot & Q-Spot 150 User Manual 1. Clamp 2. Safety cable 3. -
Page 10: Operating Instructions
4. Press the [Enter] button to store your selection. The display will read “PASS” to confirm your selection Q-Spot & Q-Spot 150 User Manual [Enter] Confirms selection [Choose] Access to main menu [Up] Toggle menu items in a forward direction... -
Page 11: Operating Modes
Carry over settings from Master Unit Carry over settings from Master Unit Pan invert Tilt invert You can change the Pan and Tilt Invert settings freely. Q-Spot & Q-Spot 150 User Manual OTES Master mode Sound activated Run built-in programs... -
Page 12: Dmx Mode
1. Press the [Choose] button until the display reads “ANNN” where N representsa number from 0 to 2. Press the [Up] and [Down] buttons to increase or decrease values until the desired value is achieved. 3. Press the [Enter] button to activate selection. Q-Spot & Q-Spot 150 User Manual Daisy Chain Connection Operating Instructions 2005-11-15/13:11... -
Page 13: User Configurations
You can apply a pan and tilt Invert by following the settings in the table below. UNCTION P5 & P6 Q-Spot & Q-Spot 150 User Manual ESCRIPTION OTES 16 bit Control... -
Page 14: Segment Display Configurations
2. Press and hold the [Enter] button. 3. Press the [Up] button then the [Down] button. 4. Action is confirmed by a “dEFA” on the read out display, followed by a fixture reset. Q-Spot & Q-Spot 150 User Manual OTES Invert display... -
Page 15: Appendix
XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’) -
Page 16: Dmx Channel Values (16 Bit)
EFAULT -> 3 <- -> 2 <- Q-Spot & Q-Spot 150 User Manual ALUE 000 255 Left > Right ( 128 = center) 000 255 Tilt Up > Down (128 = center) 000 255 Pan (Fine) 000 ... -
Page 17: Maintenance
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. -
Page 18: General Troubleshooting
Remote does not work Make sure connector is firmly connected to device Stand alone mode All CHAUVET lighting fixtures featuring stand-alone functions do not require additional settings, simply power the fixture and it will automatically enter into this mode Unit wobbles when... -
Page 19: Technical Specifications
Current draw (Q-Spot™) ... (peak 324W @ 120V), (inrush 720W @ 120V) Current draw (Q-Spot™) ... (peak 359W @ 230V), (inrush 741W @ 230V) Current draw (Q-Spot™ 150) ... (peak 251W @ 120V), (inrush 466W @ 120V) Current draw (Q-Spot™ 150) ... (peak 289W @ 230V), (inrush 433W @ 230V) LAMPS HTI150 ...
Need help?
Do you have a question about the Q-Spot and is the answer not in the manual?
Questions and answers