ABLE OF ONTENTS 1. BEFORE YOU BEGIN... 3 ... 3 HAT IS INCLUDED ... 3 NPACKING NSTRUCTIONS AC P ... 3 OWER ... 3 ONTACT ... 4 AFETY NSTRUCTIONS 2. INTRODUCTION ... 5 ... 5 EATURES DMX C HANNEL UMMARY CHANNEL MODE DMX C HANNEL...
0% to 100% switch. Contact Us W o r l d W i d e General Information Technical Support World Wide Web COLORpalette User Manual EGIN Chauvet Lighting 3000 North 29 Court Hollywood, FL 33020 voice: 954.929.1115 fax: 954.929.5560 toll free: 800.762.1084...
Do not daisy chain power to more than # units. (If applicable) ????? Is there a power out socket? Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact CHAUVET at: 954-929-1115. COLORpalette User Manual 2006-12-13/17:00...
2. I NTRODUCTION Features 6 to 27-channel DMX-512 LED bank system Operating modes: Blackout/static/dimmer/strobe RGB color mixing Color fade Automatic built-in programs with sound activation RGB control of up to 8 individual sections Built-in automated programs via master/slave or DMX Built-in sound activated programs via master/slave or DMX Ad d i t i o n a l F e a t u r e s Additional power output for daisy chaining units together...
Maximum recommended number of fixtures on a serial data link: 32 fixtures Data Cabling To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create your own cable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.
3-PIN TO 5- PIN CON VE R SION CHAR T Note! If you use a controller with a 5 CHAUVET Model No: DMX5M, or DMX5F. The chart below details a proper cable conversion: IN TO ONVERSION Ground/Shield...
Master/Slave Fixture Linking 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector.
4. O PERATING Navigating the Control Panel Access control panel functions using the four panel buttons located directly underneath the LCD Display. Button Used to access the menu or to return to a <MODE> previous menu option Scrolls through menu options in ascending <UP>...
Menu Values ALUE Menu Functions ESCRIPTION PTION Auto Mode – Stand-alone: Sets the fixture to Master status for Master-Slave operation and the built in programs will be triggered by the sound. No data link is required; all fixtures can be set to this mode for Stand-alone operation. DMX: The fixture will be controlled by a DMX signal coming from a DMX controller.
Operation Stand-Alone Mode (Sound-Active, Auto Mode): This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto Mode. Press the <MODE> button. Use the <UP> and <DOWN> buttons to locate the desired program (A001 – A024). Some programs are static, and some can trigger to sound.
If you still have a problem after trying the above solutions, please contact CHAUVET Technical Support at the location on the next page. COLORpalette User Manual...
XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return.
Need help?
Do you have a question about the LED-PALET and is the answer not in the manual?
Questions and answers