OttLite T81G5T Quick Start Manual

Assembly Package A:
DO NOT USE SHADE
IN THIS AREA
DO NOT USE SHADE NE PAS PLACER
IN THIS AREA L'ABAT-JOUR DANS
CETTE ZONE.
NO UTILICE LA
NO UTILICE LA
PANTALLA EN ESTA
AREA PANTALLA EN ESTA
AREA
NE PAS PLACER
L'ABAT-JOUR DANS
CETTE ZONE.
18w Wing Shade Floor Lamp
18w Wing Shade Floor Lamp
T81G5T T81G5T-SHPR
K15PNB V11M47 S6237T
INS120046 REV111212
INS90011 REV060109
ENGLISH
CONGRATULATIONS!
You've purchased the finest in natural lighting
technology with your new OttLite
STEP 1: PRODUCT REGISTRATION FORM
Please complete the enclosed Product
A
Registration Form and return it today
by mail, or register online by going to:
B
www.OttLite.com/warranty.
WARNING: To prevent electric shock, make
sure the lamp is not plugged in until all
assembly steps are complete.
C
CAUTION: TIP HAZARD
DO NOT MOVE SHADE OR ACCESSORIES
outside of the shaded area as shown in
Figure 1. Shade and accessories must be
kept within the shaded area and must align
in the same forward-facing direction as the
base.
STEP 2: LAMP ASSEMBLY
1. Screw the upper lamp stem (B) into the lower
lamp stem (C).
2. Firmly insert the assembled stem of the lamp
H
into the hole located in the top of the base (H).
Note: Depending on the Assembly Package
you receive, use corresponding instructions
for steps 3 to 5.
Assembly Package B:
D
Assembly Package A:
E
3. Remove the wrench (G), nut (F) and washers
F
(D, E) from the plastic bag (included in the box
G
containing the base).
4. Insert the nut (F) over the lock washer (E),
then over the flat washer (D), and finally onto
the recessed bolt in the bottom of the base. (H).
5. Using the wrench (G) provided, tighten the
nut (F) firmly by turning clockwise.
FIGURE 1 / FIGURA 1
Assembly Package B:
3. Remove the wrench (G), bolt (F) and washers
FIGURE 1 / FIGURA 1
(D, E) from the plastic bag (included in the box
containing the base).
Usable area for shade
4. Insert the bolt (F) through the lock washer
Zone sécuritaire pour (E), then through the flat washer (D), and finally
Usable area for shade
into the recessed hole in the bottom of the
l'abat-jour
base (H).
Area útil para la pantalla
Area útil para la pantalla
Zone sécuritaire pour 5. Using the wrench (G) provided, tighten the
bolt (F) firmly by turning clockwise.
l'abat-jour
CFO-002
CAUTION!
T81G5T
or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
Wing Shade Floor Lamp
ENGLISH
STEP 3: TUBE INSERTION/
REPLACEMENT
1. Make sure the lamp is not plugged into an
® product.
electrical socket.
CONGRATULATIONS!
You've purchased the finest in natural lighting technology with
2. If the lamp has been in use, allow it to cool
your new OttLite ® product.
for approximately 5 minutes before proceeding.
STEP 1: PRODUCT REGISTRATION FORM
3. Set the lamp upright on the floor.
Please complete the enclosed Product Registration Form and
4. To install a tube (A) in the socket, grasp
return it today by mail, or register online by going to: www.ott-lite.
the tube firmly in your hand. Clip the tube into
com/warranty.
the shade clip (M) and push the tube straight
WARNING: To prevent electric shock, make sure the lamp is not
into the socket (N) until it "snaps" into
place (O). Do not apply pressure to the
plugged in until all assembly steps are complete.
glass end of the tube.
CAUTION: TIP HAZARD. DO NOT MOVE SHADE OR
5. To remove a tube already installed in the
ACCESSORIES outside of the shaded area as shown in Figure 1.
Shade and accessories must be kept within the shaded area and lamp, grasp the tube firmly in your hand and
angle it slightly out of the shade clip (M)
must align in the same forward-facing direction as the base.
approximately 15 degrees (P) and pull it straight
out of the socket. Do not twist or turn the
LAMP ASSEMBLY
tube while removing it from the socket.
1. Screw the upper lamp stem (B) into the lower lamp stem (C).
2. Firmly insert the assembled stem of the lamp into the hole 6. Position the shade as desired by flexing the
located in the top of the base (H).
neck.
3. Remove the wrench (G), bolt (F) and washers (D, E) from the
7. Plug the lamp into a standard 120V socket.
plastic bag (included in the box containing the base).
Your lamp is ready for use.
4. Insert the bolt (F) through the lock washer (E), then through
the flat washer (D), and finally into the recessed hole in the
Please note that in operation, OttLite
bottom of the base (H). not dimmable.
5. Using the wrench (G) provided, tighten the bolt (F) firmly by
Enjoy your OttLite
turning clockwise.
This lighting system is designed
TUBE INSERTION/REPLACEMENT
for use with OttLite
1. Make sure the lamp is not plugged into an electrical socket.
(model number T18330). Use of
2. If the lamp has been in use, allow it to cool for approximately
other products voids the warranty
5 minutes before proceeding. and may result in damage to the
lighting system.
3. Set the lamp upright on the floor.
4. To install a tube (A) in the socket, grasp the tube firmly in your
hand. Clip the tube into the shade clip (M) and push the tube
straight into the socket (N) until it "snaps" into place (O).
Do not apply pressure to the glass end of the tube.
5. To remove a tube already installed in the lamp, grasp
the tube firmly in your hand and angle it slightly out of the
shade clip (M) approximately 15 degrees (P) and pull it straight
out of the socket. Do not twist or turn the tube while removing
it from the socket.
6. Position the shade as desired by flexing the neck.
7. Plug the lamp into a standard 120V socket. Your lamp
is ready for use.
Please note that in operation, OttLite
dimmable.
Enjoy your OttLite Wing Shade Floor lamp!
®
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
CAUTION! IMPORTANT SAFETY INSTR
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN TH
This lighting system is designed for use with OttLite
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED O
type (Style Number PL18-B). Use of other products
PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DO
voids the warranty and may result in damage to the
QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG
lighting system.
DO NOT ALTER THE PLUG.
CAUTION!
CAUTION:
this luminaire is damaged, it shall be exclusively replaced by the
FULLY INSERT.
manufacturer or its service agent or a similar qualified person in order
to avoid a hazard. Indoor use only.
CAUTION!
blade of plug to wide slot, fully insert.
¡ PRECAUCIÓN! INSTRUCCIONES DE S
CAUTION! IMPORTANT
IMPORTANTES:
SAFETY INSTRUCTIONS:
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS
COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRIC
This portable lamp has a polarized plug (one blade is wider than the
other) as a feature to reduce the risk of electric shock. This plug will
CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCH
fit in a polarized outlet only one way. If the plug does not fit fully in
® tubes are
EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN CO
the outlet, reverse the plug. If it still does not fit, contact a qualified
CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE PUE
electrician. Never use with an extension cord unless plug can be fully
Easyview Craft lamp!
®
inserted. Do not alter the plug.
INSERTADO. NO ALTERE EL ENCHUFE.
This product complies with Part 18 of FCC Rules, but may cause
PRECAUCIÓN:
tubes only
® interference to radios, televisions, wireless telephones, and
remote controls. Avoid placing this product near these devices. If
ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
interference occurs, move the product away from the device or plug
either into a different outlet. Do not install this product near maritime
safety equipment or other critical navigation or communication
equipment operating between 0.45-30 MHz.
AVERTISSEMENT! IMPORTANTES DIRE
SÉCURITÉ:
CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE (UNE LAME PLUS
DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQ
LA PRISE QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERS
TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS AV
tubes are not
®
LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCUR
AVERTISSEMENT:
FICHE DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.
18w Wing Shade Floor Lamp
®
If the external flexible cable or cord of
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF P
To prevent electric shock, match wide
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAG
POUR ÉVITER LES CHOCS ÉLECTRIQUE, IN