Casio Illuminator AQ51-7E General Manual

OPERATION CHART:MODULE QW-1310
B
• Press to change from mode to mode.
D
• In any mode, hold down to illuminate the face of the watch.
B
C
TIMEKEEPING MODE
To set the digital time
Hour hand Minute hand 1. Hold down
digits start to flash on the digital display.
The seconds flash because they are selected .
2. Press
B
A
C D
• Once you reach the Timekeeping display, you have to hold down
again to display the flashing seconds.
Seconds
Hour
3. While the seconds digits are selected (flashing), press
Minutes
the seconds to "00". If you press
the range of 30 to 59, it is reset to "00" and 1 is added to the minutes.
PM indicator
If the seconds count is in the range of 00 to 29, the minutes count
is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press
B
down changes the current selection at high speed. While the 12/24 hour setting is selected, press
to switch between the two formats.
C
5. After you set the time and format, press
• If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the
watch goes back to the Timekeeping Mode automatically.
To set the analog time
A
When in the any Mode, press to advance the analog time setting.
A
Hold down advances the analog setting at high speed. You can only advance the setting and cannot reverse
it.
To set the date
1. Hold down
flash on the digital display. The month digits flash because they are
selected .
B
A
2. Press
c D
• Once you reach the Date Mode display, you have to hold down
again to display the flashing month.
Month Day of week
3. While the month or date digits are selected (flashing), press
increase the number. While the day of the week is selected,
Date
pressing
the current selection at high speed.
C
4. After you set the date, press to select the Date Mode.
• The watch does not make any allowance for leap years. Be sure to manually set February 29 (when one
occurs) for the appropriate date.
• If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the
watch goes back to the Timekeeping Mode automatically.
ALARM MODE
Alarm ON indicator When the Daily Alarm Function is switched on, the alarm sounds for
20 seconds at the preset time each day. Press any button to stop the
Mode indicator
alarm after it starts to sound. When the Hourly Time Signal is switched
on, the watch keeps every hour on the hour. Note that the Daily Alarm
and the Hourly Time Signal operate based on the digital time setting.
• If you do not press any button for a few minutes in the Alarm Mode,
B
A
the watch goes back to the Timekeeping Mode automatically.
D
C
To set the alarm time
1. Hold down
flash on the display. The hour digits flash because they are
selected .
Hour
Hourly Time
Minutes
Signal ON
indicator
C
2. Press to change the selection in the following sequence.
Hour Left Minutes Digit
Alarm Mode
• Once you reach the Alarm Mode display, you have to hold down
B
3. Press to increase the selected digits. Holding down
• The format (12-hour or 24-hour) of the alarm time matches the format you select for digital timekeeping.
• When setting the alarm time you using the 12-hour format, take care of set the time correctly as morning
or afternoon.
Timekeeping Mode Date Mode
A
D
C
while in the Timekeeping Mode until the seconds
C
to change the selection in the following sequence.
Seconds Hour Minutes
Timekeeping
12/24-Hour Format
B
while the seconds count is in
B
to increase the number. Holding
to select the Timekeeping Mode.
DATE MODE
C
while in the Date Mode until the month digits start to
C
to change the selection in the following sequence.
Month Date Day of week Date Mode
B
advances to the next day. Holding down
C
while in the Alarm Mode until the hour digits start to
Right Minutes Digit
Alarm/Hourly Time Signal Setting
C
again to display the flashing hour.
B
changes the selection at high speed.
GENERAL GUIDE
Dual Time Mode
Alarm Mode
4. While the Daily Alarm/Hourly Time Signal setting is selected, press
sequence.
5. After you make your alarm setting, press
• If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the
watch goes back to the Timekeeping Mode automatically.
C
To test the alarm
B
to reset
Hold down B in any mode to sound the alarm. Note that pressing B also changes the mode.
B
B
C
Hour Seconds
Minutes
Mode indicator
• Once you reach the Dual Time Mode display, you have to hold down
B
3. Press to increase the selected digits. Holding down
12/24-hour setting is selected, press
4. After you set the time, press
• If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the
watch goes back to the Timekeeping Mode automatically.
C
Mode indicator
B
to
B
changes
B
C
Minutes 1/100 second
Seconds
— 1 —
Stopwatch Mode
[Alarm ON Indicator/Hourly Time Signal ON Indicator]
Both ON Both OFF Daily Alarm only Hourly Time
C
to select the Alarm Mode.
DUAL TIME MODE
The Dual Time function lets you set a second digital time that operates
independently of the current analog and digital times. This means you
can keep track of time in another time zone.
A
To set the Dual Time
D
C
1. Hold down while in the Dual Time Mode until the hour digits start
to flash on the display. The hour digits flash because they are
selected .
C
2. Press to change the selection in the following sequence.
Hour
Dual Time Mode
B
changes the selection at high speed. While the
B
to switch between the two formats.
C
to select the Dual Time Mode.
STOPWATCH MODE
The Stopwatch Mode measures elapsed time and cumulative elapsed
time. The range of the stopwatch is 59 minutes, 59.99 seconds.
To measure elapsed time
C
1. Press to start the stopwatch.
C
2. Press to stop the stopwatch.
A
C
3. Hold down until the stopwatch is cleared to "00:00 00".
To measure cumulative elapsed time
C
1. Press to start the stopwatch.
D
C
2. Press to stop the stopwatch.
C
3. Press again to resume timing from the time shown on the display.
You can repeat steps 2 and 3 as many times as you like.
C
4. Hold down until the stopwatch is cleared to "00:00 00".
B
to change the status in the following
Signal only
Minutes
12/24-Hour Format
C
again to display the flashing hour.