Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for GT ALARM GT 800/1
- Page 1 GT 800/1/2/3 USER AND INSTALLATION MANUAL...
-
Page 2: Table Of Contents
SUMMARY 1.0 - INSTALLATION AND CONNECTIONS Page. 3 2.0 - GENERAL CONNECTION DIAGRAM Page. 5 3.0 - DESCRIPTION OF THE PROGRAMMABLE FUNCTIONS Page. 6 3.1 - Self-coding vehicle indicators impulses number Page. 6 3.2 - Switches/Discriminators signals stabilizer Page. 6 3.3 - Memorization of switches/discriminators signals only after actuator signals Page. -
Page 3: Installation And Connections
1.0 - INSTALLATION AND CONNECTIONS WARNINGS: - Place the GT800 alarm in the engine compartment, away from direct sources of water spray and high tension wiring. Solder and isolate all connections. - Isolate the wires not connected. - The alarm system should be mounted by a professional installer. 1 - Connect the BROWN wire to O/E vehicle earth. - Page 4 14 - The RED/BROWN, YELLOW/BROWN, RED/GREY and YELLOW/GREY wires must be connected to the original vehicle central door locking system as indicated on the vehicles installation guides supplied by GT, or following the section DESCRIPTION OF THE ALARM SYSTEM ARMING/DISARMING COMMAND WIRES (Page 8). 15 - Connect the GREEN/YELLOW wire to O/E vehicle earth to carry out the DOORS LOCK/ UNLOCK SIGNALS SELF-CODING procedure and to carry out the RAPID TEST (page 8-9).
-
Page 5: General Connection Diagram
2.0 - GENERAL CONNECTION DIAGRAM LEGEND: = FUSE TO BE INSERTED 13 12 ULTRASONIC RED LED - Pos. 10 LED/BUTTON TRANSDUCRES BLACK/RED - Pos. 14 BLACK - Pos. 17 RED - Pos. 10 WHITE WHITE POSITIVE +12 V DOORS PIN SWITCHES RED - Pos. -
Page 6: Description Of The Programmable Functions
3.0 - DESCRIPTION OF THE PROGRAMMABLE FUNCTIONS 3.1 - Self-coding vehicle indicators impulses number. When you enable this function it is possible to self-code the indicators flashes number to the alarm system when doors are locking (system arming) and when doors are unlocking (system disarming). - Page 7 NUMBER OF LED BUTTON NUMBER OF LED BUTTON CONDITION PRESSES ALARM SYSTEM The DEFAULT /LED FLASHES FUNCTION OF THE LED programming are in “bold” FOR THE BUTTON FUNCTIONS LED OFF LED ON STATUS CHECK Self-coding indicators Disabled Enabled impulses number Switches/Discriminators Activated Deactivated...
-
Page 8: Description Of The Alarm System Arming/Disarming Command Wires
5.0 - DESCRIPTION OF THE ALARM SYSTEM ARMING/DISARMING COMMAND WIRES A - Using the RED/BROWN and RED/GREY wires you can arm and disarm the alarm using the original vehicle remote, or door key lock. - RED/BROWN WIRE: Connect to the vehicle wire that changes state when locking the doors. - RED/GREY WIRE: Connect to the vehicle wire that changes state when unlocking the doors. -
Page 9: Rapid Test
6 - Unlock the vehicle using the original remote control, after a couple of seconds the alarm will emit 2 visual signals (indicators), and 3 acoustic signals indicating the end of self coding and the doors will unlock. Warning: The procedure can be considered carried out correctly only if the operations are in compliance with the points 5 and 6. -
Page 10: Self-Power Supply
The RAPID TEST procedure can be stopped in two ways: A - After about 2 minutes from the test function activation, the alarm system emits a long acoustic signal and it comes out automatically if any other sensor has not been activated. B - Pressing the door locking button from the original vehicle handset the alarm system emits a long acoustic signal and it comes out from the function. -
Page 11: User Manual
10 .0 - USER MANUAL 10.1 - ALARM SYSTEM ARMING/DISARMING. Locking the doors using the original remote control handset, the alarm system will arm and it will generate 1 acoustic signal (if the function is activated you will obtain also a visual signal supplied by the indicators). -
Page 12: Emergency Disarming With "Gt Card Code" Page
10.6 - EMERGENCY DISARMING WITH “GT CARD CODE”. In case of emergency (i.e. the battery of the original vehicle handset is discharged, etc.) it is possible to disarm the alarm system using the GT CARD CODE. It is necessary to carry out the following procedure: 1 - Take the “GT CARD CODE”... -
Page 13: Visual Signal Function When Arming/Disarming The Alarm System Page
11.0 - COMPLIANCE DECLARATION Getronic S.r.l. Via Calcinate, 12 Gavirate, Italia, hereby declares that GT 800/1/2/3 as been approved under the following European Directives as issued by the European Community: R&TTE 1999/5/CE (including the directives: 95/54/CE - 95/56/CE - EN 60950) The manufacturer holds the homologation certificates and the documents required for compliance evaluation. -
Page 14: Warranty Conditions
12.0 - WARRANTY CONDITIONS This Certificate should be kept in a safe place and produced for verification should technical assistance be required. Inability to produce this Certificate may affect your warranty rights. Warranty period begins from date of purchase and is valid for 24 months. Should technical assistance be required during the warranty period, you should take your vehicle and this Certificate to either the original installer or the nearest GT Auto Alarm Service Centre for inspection. -
Page 15: Technical Features
13.0 - TECHNICAL FEATURES GT800: - Input voltage 12V ± 4 Vdc - Current draw (Disarmed alarm) < 10 mA - Current draw (Armed alarm) < 20 mA - Positive output when the alarm is armed 80 mA - Negative intermittent output in alarm 100 mA - Engine immobilisation relay contact capacity 15 A @ 15 Vdc... - Page 16 Getronic S.r.l. Via Calcinate no. 12 21026 Gavirate (VA) Italy Tel. +39 0332 756011 Fax + 39 0332 731162 www.gtalarm.it InstGT800UKRev00.p65...
Need help?
Do you have a question about the GT 800/1 and is the answer not in the manual?
Questions and answers