Order No.HUD0311343C3 Washing Machine NA-F80GD Product Color : White CONTENTS Page Page 1 SPECIFICATIONS 9 TEST RUNNING WITHOUT WATER 2 SCHEMATIC DIAGRAM 9.1. METHOD TO TEST RUNNING WITHOUT WATER 2.1. For 3 pin plug 10 LOCATION 2.2. For 2 pin plug 10.1.
3 PRODUCT INFORMATION 3.1. Timer type drying function Below half the height of the stainless steel part of the tub represents a load of under 3.0kg. The heater, fan motor and fan case are providing inside of the panel, and drying function shall be operated by timer control. Exhaust air including humid air shall be come out from upper portion of the tub through the exhaust filter.
Drying process (Normal timer course) 3.2. Use the “ TUB DRY “ function to prevent black mold Activating “Tub Dry” after the wash is complete eliminates the humidity in the tub that is one cause of black mold. (Activate once a week) 1.
4 CHECK INPUT AND OUTPUT VOLTAGE OF THE PC.BOARD 1. Before replace PC.Board, check input and output voltage of the PC.Board. 2. Check range of the test meter. 3. When check output voltage of the PC.Board, set a program of the Washing Machine on the working mode. 4.
8 DISASSEMBLY INSTRUCTIONS AND ADJUSTMENTS PC Board 1 Remove the back panel.(4 screws) (Power side) 2 Remove the insulation spacer.(5 pawls) 3 Remove the earth wire.(1 screw) 4 Remove connectors, and pull the PC Board upward to remove the PC Board w/components from the body.
Page 10
PC Board 1 Open the lid, and remove the panel A packing. After that, remove one screw (Operation mounting the panel face A. side) 2 Slide the panel face A to right to remove. 3 Turn the panel face A back side front. 4 Remove pawls holding the PC Board.
Page 11
Heater 1 Remove the body B. (Refer page of the body B) 2 Remove the connector of the heater, detector and the motor. Fan motor 3 Remove 3 screws mounting the fan case unit. 4 After open the inner lid, remove the air supply hose after remove the pawls of the duct for holding the air supply hose.
Page 12
Lid lock switch 1 Remove 2 screws mounting the body B. Lid switch 2 Turn the feed hose clockwise slightly to remove holding portion of the feed hose. 3 Open the inner lid, and remove the air supply hose by removing pawls of the air supply hose.
Page 13
Mechanism 1 Remove 2 screws mounting the body B. case 2 Turn the feed hose clockwise slightly to remove pawls, and remove the feed hose. 3 Open the inner lid, and remove the air supply hose by removing pawls of the air supply hose.
Page 14
Mechanism 8 Remove the shaft bushing, case Spinner shaft flange nut and the spinner shaft washer B. 9 Pull upward the tub to remove. 10 Lay down the machine on it nothing drain hose side. * Please spread cloth to prevent scratch on the body. 11 Remove 2 screws mounting the mounting plate B.
Page 15
Rotary 1 Lay down the machine on it nothing drain hose side. detector * Please spread cloth to prevent scratch on the body. 2 Remove 2 screws mounting the rotary detector. 3 Remove the connector. Caution to put 1 Before put the body B on to the body A, Check if the lever of the lid switch is the body B on not bent.
9 TEST RUNNING WITHOUT WATER 9.1. METHOD TO TEST RUNNING WITHOUT WATER 1. Set the power switch to “OFF”. 2. Press and hold both the “Watet level” and “Wash” buttons with one hand. 3. Set the power switch to “ON“. 4.
Page 17
9.1.1. Error indication descriptions If there is an operation error, or if there is a problem with washing machine, operation shall be stopped and warning buzzer will sound (All of U and H21), and an error indication will be display-ed Alphabet and Number alternately. Indication Contents Detect contents...
Page 18
Indication Contents Detect contents Check point Method to clear · Check if condition of the connector for Mulfunction of clutch. Geared motor won’t Press Power (Push) geared motor. operate in wash switch to OFF position process. · Replace the geared motor. ·...
10.8. REPLACEMENT PARTS LIST-D Ref. No. Description Parts No. Q’ty Remarks Lint filter AXW22A-6BM0 Detergent inlet AXW1198-6EM0 AXW2A-6PD00 Suspension unit AXW340Z-6MJ0 1 set=4 PCs. Outer tub AXW12A-6ML0 Inc. D-23 Spinner flange washer A AXW15P-6EN0 Geared motor AXW3482Z2606 220-240V, for clutch Spinner plate B AXW3232-6JU0 Lead wire unit...
10.9. PACKING PARTS LIST Ref. No. Description Part No. Q’ty Remarks Case A AXW9001N6PD0 Standard Case A AXW9001N6PDA Singapore Case A AXW9001N6PD3 Thailand Operating instructions AXW9901Z6PD0 English/Arabic Operating instructions AXW9901Z6PD3 Thailand Operating instructions AXW9901Z6PD5 English/Cantonese Case B AXW90B-6PD00 Body cover AXW9004Z6PD0 Tub supporter A AXW9054Z6PD0...