Sealey CB50.V2 Quick Start Manual

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. Safety
Warning! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using these tools.
‰
do not use tools if damaged.
8
do not use these tools for purposes they are not designed for.
8
Maintain tools in good and clean condition for best and safest performance. File or linish flush any burrs or "mushrooming" on the tools.
8
ensure that a vehicle which has been jacked up is adequately supported with axle stands.
8
Wear approved eye and ear protection. A full range of personal safety equipment is available from your Sealey stockist.
8
Wear suitable clothing to avoid snagging. do not wear jewellery and tie back long hair.
8
Account for all tools by replacing them in the carry case.
8
iMportant: These instructions are provided as a guide only.
‰
2. introduction
Assortment of body repair tools, designed for levering, separating and reforming of panels. Supplied in storage case.
3. contentS
Model number
CB50.V2-01 Cranked Panel Slapper Bar (45° dog leg)
CB50.V2-02 Cranked Panel Slapper Bar (90° dog leg)
CB50.V2-03 Panel Slapper and Prise Bar (900mm reach)
CB50.V2-04 Panel Slapper and Prise Bar (750mm reach)
CB50.V2-05 Panel Slapper and Prise Bar (580mm reach)
CB50.V2-06 Panel Slapper and Prise Bar (460mm reach)
CB50.V2-07 Panel Slapper and Prise Bar (320mm reach)
CB50.V2-08 extended Panel Separator (120mm Straight edge offset)
CB50.V2-09 Panel Separator (50mm Straight edge)
CB50.V2-10 Panel Separator (50mm Curved edge)
CB50.V2-11 extended Panel Separator (120mm Straight edge)
CB50.V2-12 Panel Separator (70mm Straight edge)
CB50.V2-13 Panel Separator (90mm Straight edge)
CB50.V2-14 Blow Mould Case
4. operation
4.1. To avoid "mushrooming", use a copper or a hard rubber mallet to drive the panel separators, items 8 through 13.
4.2. Items 8 through 13 generally used for separating sheet metal laminates, bonded or spot welded together. Use the prise bar end of
items 5 through 8 to start the separation if required.
note! It is the action of the drift angle, or wedge, which separates the laminates, not the leading straight or curved edge. These
tools are not chisels.
4.3. Use the panel slapper tools, items 3 through 7 in conjunction with an appropriate dolly (not supplied in this kit). Use to form or
remove 3 dimensional shapes in bodywork and sheet metal products.
5. Maintenance
5.1. Keep the tool working surfaces smooth with a linishing cloth or draw file.
5.2. Clean the tools with a lightly oiled cloth and return to the carry case. Store indoors, away from children.
© Jack Sealey limited
13pc Body panel levering/Separating
tool Set
Model no:
Wear protective Wear safety
gloves footwear
product name
Original Language Version
cB50.v2
Wear protective Wear ear
clothing protection
CB50.V2 Issue 1 30/12/19