Related Manuals for Cambridge Audio Incognito LM10
Summary of Contents for Cambridge Audio Incognito LM10
- Page 1 LM10...
- Page 2 Wiring guide...7 Cat-5 connections...8 Single local audio source set-up...9 Dual LM10s fitted in a single zone...11 Single LM10 with main and sub-zone fitted..12-13 Dual LM10s with main and sub-zones fitted...14 Source rotate for local 1 & 2... on the keypad...15 Audio level adjustment...17...
- Page 3 Incognito remote and/or keypad (see instruc- tions on entering local source rotate mode on page 15). The LM10 can also support sub- zones (where fitted) so that the local source is audible in both main and subzone areas.
- Page 4 Speaker cable Speakers KP10 Keypad LR10 remote control CAT-5 CAT-5 AH10 Hub 4 Incognito LM10...
- Page 5 Incognito LM10 Speaker cable Speakers KP10 Keypad LR10 remote control CAT-5 CAT-5 AH10 Hub Incognito LM10 5...
- Page 6 Be very careful to follow the colour-code that is indicated on the connector. Always double-check your connections, and your punching. Fit the LM10 to the back-box (pattress) that you have fitted in your wall. This is done with the two supplied screws (LM10-EU=M 3.5mm x 20, LM10-CU=6 x 32 pitch UNC x 6mm Countersunk).
- Page 7 The LM10 runs on 24V DC supplied through the connecting cable. As such there is no mains volt- age present in the LM10 and the unit is often safe to fit in areas where only extra low voltage (ELV) equipment is permitted. However, it is imperative that you always check the wiring regula- tions in force for your application and area.
- Page 8 A Cat-5 cable is used to connect the LM10 to a keypad output on an AH10 hub and to a KP10 amplified control module. Use Cat-5 cables (use EIA/TIA 568A RJ-45 wire configuration, see page 7) to connect from the hub to a LM10 wall plate (optional), and then wire from the wall plate to the KP10 (see opposite diagrams).
- Page 9 AH10 Hub LM10 Rear CAT-5 AH10 Hub LM10 Rear CAT-5 Incognito LM10 KP10 CAT-5 KP10 CAT-5 Speaker Cable MAIN ZONE Speaker Cable MAIN ZONE Incognito LM10 9...
- Page 10 It is possible to add up to two LM10 units per main zone. This gives you the option to listen to either one by selection from the keypad or LR10 remote control (Local1/Local 2). The module needs to be told whether there are one or two LM10’s present.
- Page 11 Local Source 1 AH10 Hub CAT-5 SW1 SW2 AH10 Hub Local Source 1 CAT-5 Local Source 2 CAT-5 CAT-5 SW1 SW2 Local Source 2 CAT-5 Incognito LM10 KP10 Speaker Cable MAIN ZONE KP10 Speaker Cable CAT-5 MAIN ZONE Incognito LM10 11...
- Page 12 Connect the LM10 as shown in the diagrams. Switch over SW1 (LC1) to the ON position and SW2 (LC2) to the OFF position. The LM10 will respond to the Local 1 remote command when selected. AH10 Hub CAT-5 CAT-5 12 Incognito LM10...
- Page 13 AH10 Hub CAT-5 CAT-5 Incognito LM10 Local Source 1 CAT-5 CAT-5 SUB-ZONE KP10 Speaker Cable MAIN ZONE KP10 Speaker Cable Incognito LM10 13...
- Page 14 Note: If using an LR10 to select the local source, this will ONLY select Local 1 as default. Local Source 1 AH10 Hub CAT-5 CAT-5 SW1 SW2 AH10 Hub Local Source 1 CAT-5 CAT-5 14 Incognito LM10 Local Source 2 CAT-5 CAT-5 CAT-5 CAT-5 SW1 SW2 Local Source 2 CAT-5 CAT-5...
- Page 15 Mode Switch is set to “AH10” mode. LM10s can only be used in this mode. Please refer to your LM10 Installation Guide for more information. Pressing the Select left or right buttons on the key- pad allows you to rotate through all six sources as default.
- Page 16 Note: If no adjustment is made the system will automatically go back to volume adjustment after two seconds. If “Standard A-BUS/Incognito Ready” mode is selected on the Mode switch, the KP10 will only rotate round the main 6 sources. 16 Incognito LM10...
- Page 17 -clockwise decreases it. LM10 The LM10 also has a local infra-red (IR) output allowing for local source equipment to be con- trolled via an IR1. This will only pass through remote source or commands once the local source has been selected (Local 1 or Local 2) from the LR10 remote or KP10 keypad.
- Page 18 To obtain warranty service, please contact the Cambridge Audio authorised dealer from which you purchased this product. If your dealer is not equipped to perform the repair of your Cambridge Audio product, it can be returned by your dealer to Cambridge Audio or an authorised Cambridge Audio service agent. You will need to ship this product in either its original packaging or packaging affording an equal degree of protection.
- Page 19 Incognito LM10 Incognito LM10 19...
Need help?
Do you have a question about the Incognito LM10 and is the answer not in the manual?
Questions and answers