Sealey PEH5001 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to electrical
instructions shock
Hazard
1. safety
1.1. electrIcal safety
warnInG! ElEctrical installation of thE BEnch GrinDEr to a 3-phasE 415Volt supply must only BE
‰
carriED out By a qualifiED ElEctrician.
1.1.1. make sure the power supply cable is correctly connected to the earth. it is the user's responsibility to read, understand and
comply with the following:
1.1.2. You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads,
plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of
appropriate safety devices. An rccB (residual current circuit Breaker) should be incorporated in the main distribution board.
1.1.3. you must also read and understand the following instructions concerning electrical safety.
the Electricity at Work act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance tester (PAt), at least once a year.
the health & safety at Work act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. if in any doubt about electrical safety, contact a qualified electrician.
1.1.4. ensure insulation on all cables and the product itself is safe before connecting to mains power supply.
1.1.5. ensure that cables are always protected against short circuit and overload.
1.1.6. regularly inspect power supply, leads, plugs and all electrical connections for wear and damage,
especially power connections, to ensure that none are loose.
1.1.7. important: ensure the voltage marked on the product is the same as the electrical power supply
to be used. A three phase plug must be fitted to this machine.
dO nOt pull the powered appliance by the power cable.
8
dO nOt pull power plugs from sockets by the power cable.
8
dO nOt use worn or damage leads, plugs or connections. immediately replace or have repaired
8
by a qualified electrician.
1.1.8. this product must be fitted with a 3-phase plug according to the diagram, and will
require a minimum supply of, 16amps per phase.
1.1.9. you must contact a qualified electrician to ensure an appropriately fused supply is
available. connect Green/yellOw wire to earth (e) terminal.
connect the live wires to live 1, 2 and 3.
1.1.10. When completed, check that there are no bare wires, that all wires have been connected correctly, that the cable external
insulation extends beyond the cable restraint and that the restraint is tight.
1.2. General
warnInG! disconnect the heater from the mains power supply before carrying out any servicing or maintenance.
‰
maintain the heater in good order and clean condition for best and safest performance. replace or repair damage parts.
9
locate heater in a suitable work area and keep area clean, tidy and free from unrelated materials. ensure there is adequate
9
lighting and keep the immediate area in front of the outlet grille clear.
Allow the unit to cool before storage. When not in use, disconnect from the mains power supply and store in a safe, cool, dry,
9
childproof area.
only use the heater standing in the upright position on a level surface.
9
dO nOt use the heater where there are flammable liquids, solids or gases such as petrol, solvents, aerosols etc, or where heat sensitive materials
8
may be stored.
dO nOt place the heater near items that may be damaged by heat, allow at least 2mtr clearance in front of the heater.
8
dO nOt allow the heater to get wet as this may cause an electric shock, causing damage to the heater and possible personal
injury.
dO nOt let power lead hang over an edge (i.e. table), or touch a hot surface, lie in the beam of heat, or run under a carpet.
8
dO nOt use in bathroom, shower room, or in any wet or damp environments or where there is high condensation.
8
dO nOt operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
dO nOt insert or allow objects to enter any openings of heater as this may cause an electric shock, fire or damage to heater.
8
dO nOt use heater if the power cord, plug or the heater is damaged, or if the heater has become wet.
8
dO nOt use the heater for any purpose other than for which it is designed.
8
dO nOt use a timer or other remote device to operate the heater.
8
© Jack sealey limited
instructions for
IndustrIal ptc fan heater 5000w/415V
model no:
Hot surfaces do not cover
Original Language Version
peh5001
PeH5001 / | issue 1 31/05/16