Advertisement
4. FIxING INSTRUCTIONS
4.1 WB951LED: 12mm Single Bolt Fixing
4.1.1. Drill a 13mm mounting hole in a suitable point on the vehicle.
4.1.2. Connect to cables of at least 2mm² section and use an 8A fuse; check polarities.
4.1.3. Fix the beacon by using nuts and washers according to the type and shape of the mounting surface
4.2 WB952LED: Three Bolt Fixing Base
4.2.1. Drill mounting holes using the beacon base as a template. Also make provision to route cables into the vehicle.
4.2.2. Connect to cables of at least 2mm² section and use an 8A fuse; check polarities.
4.2.3. Fix the beacon with 3 x M6 screws.
4.3 WB953LED: Fixed Spigot Base
●
Use in connection with DIN spigot (a range of DIN mountings is available: please see Sealey catalogue).
●
DIN adaptor mounts to vehicle allowing removal/installation without tools.
●
Suitable for situations where security is a problem.
4.3.1. Fit a suitable adapter socket onto the vehicle. Make sure it is perfectly vertical.
4.3.2. use cables of at least 2mm² section and use an 8A fuse; check polarities.
4.3.3. Push the beacon spigot down fully onto the adapter socket and secure by tightening the wing nut.
4.3.4. When the beacon is removed, always close the adapter socket outlet using the rubber cap.
4.4 WB954LED: Magnetic Base
●
Fitted with high power magnet strong enough to cope with normal road speeds.
●
Supplied with 3mtr coiled flex and universal auxiliary power outlet plug.
4.4.1. The beacon must be placed on a surface parallel to the ground.
3.4.2. The surface should be flat and clean to ensure good adherence.
4.5 WB955LED: Flexible Base with DIN Spigot Mounting.
4.5.1. Fit a suitable adapter socket onto the vehicle. Make sure it is perfectly vertical.
4.5.2. use cables of at least 2mm² section and use an 8A fuse; check polarities.
4.5.3. Push the beacon spigot down fully onto the adapter socket and secure by tightening the wing nut.
4.5.4. When the beacon is removed, always close the adapter socket outlet using the rubber cap.
5. VOLTAGE SELECTION
The beacons will switch between 12V and 24V automatically.
6. FLASH PATTERN SELECTION
6.1.
Three flash patterns are available by selecting one of the three switch positions as in fig.2. The switch is accessed by removing
the dome as in fig.1.
6.2.
Switch 1: Rotating flash; flash rotates mimicking a rotary beacon.
Switch 2: Six rapid flashes followed by a break.
Switch 3: Two flashes followed by a break.
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a
recycling centre and disposed of in a manner which is compatible
with the environment.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No responsibility is accepted for incorrect use of this equipment.
WARRANTY: Guarantee is 12 months from purchase date. Proof of purchase will be required for any claim.
INFORMATION: Please call us for a copy of our latest catalogue on 01284 757525, leaving your name, address and postcode.
© Jack Sealey Limited
fig.1
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park, Bury
St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
fig.2
WEEE Regulations.
Dispose of this product at the end of its working life in compliance
with the Eu Directive on Waste Electrical and Electronic Equipment.
When the product is no longer required, it must be disposed of in an
environmentally protective way. Contact your local solid waste
authority for recycling information.
01284 757500
01284 703534
WB951LED,WB951LED,WB953LED,
WB954LED,WB955LED
www.sealey.co.uk
sales@sealey.co.uk
ISSuE: 1 12/12/13
Advertisement
