Sealey AP28104 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1 GENERAL SAFETY
 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations
are adhered to when using this product.
 WARNING! Use caution when handling and assembling the metal components. The metal may
have sharp edges or corners, the use of protective gloves is recommended.
 DO NOT open more than one drawer at a time.
 DO NOT step on the drawers.
 DO NOT let children play with the roll cab or top chest.
 Ensure all drawers are fully closed and the self locking catch is activated, before moving the toolbox.
 Secure the brakes when rollcab is in the desired position.
 Keep the work area clean, uncluttered and ensure there is adequate lighting.
 Keep the mounting frame clean and tidy in accordance with good workshop practice.
 DO NOT use in damp work areas.
 WARNING! The warnings, cautions and instructions referred to in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood that common
sense and caution are factors which cannot be built into this product, but must be applied by the
operator.
2. INTRODUCTION
AP28104:
Retro styled top chest with modern day functionality. Features 4 drawers with ball bearing
slides and lift latch drawer pulls preventing inadvertent opening. Chest is further enhanced
with opening clam shell top providing additional storage. Retro theme is continued with
chrome plated top lid stays and side handles. Drawers and top lid are fitted with drawer liners
and lock on one key turn. For use as stand alone unit or with AP28204 Roll Cab to make a
complete retro style stack unit.
AP28204:
Retro styled roll cab with modern day functionality. Features 4 drawers with ball bearing slides
and lift latch drawer pulls preventing inadvertent opening. Retro theme is continued with
stainless steel handle and stylish heavy duty castors, two with brakes. All drawers are fitted
with drawer liners and lock on one key turn. For use as stand alone or with AP28104
Topchest to make a complete retro style stack unit.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AP28104 . . . . . . . . . . . . . . . . AP28204
Overall Dimensions (W x D x H):. . . . . . . . 700 x 450 x 495mm . . . . . . . . 715 x 460 x 825mm
Large Drawer x 1: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . n/a . . . . . . . . 570 x 400 x 105mm
Large Drawer x 3: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . n/a . . . . . . . . 570 x 400 x 135mm
Medium Drawer x 4: . . . . . . . . . . . . . . . . . . 570 x 400 x 60mm . . . . . . . . . . . . . . . . . . . . . n/a
Clam Shell Top: . . . . . . . . . . . . . 590 x 430 x 80mm (restricted) . . . . . . . . . . . . . . . . . . . . . n/a
4. ASSEMBLY
4.1. Roll Cab Handle Installation.
Position the handle over the holes in the roll cab, attach using the M6 x 12mm hex bolts
and tighten securely (fig.1). Assembling the handle first will make it easier to handle the
the roll cab.
4.2. Castor Installation.
4.2.1. Lay the roll cab carefully on its back, protecting it with a soft mat placed on the floor.
4.2.2. Position the two rigid castors at the end opposite the handle.
4.2.3. Insert the M8 x 20mm hex bolts through the washers, then through the castors and into
the base of the roll cab, tightening securely.
4.2.4. Repeat with the two swivel castors on the opposite (handle) end.
4.3. Roll Cab and Top Chest Connection.
4.3.1. Place the top chest onto the roll cab.
4.3.2. Snap the connectors into the square holes on the back of the top chest (fig.3.).
4.3.3. Fasten the connectors with the screws provided.
© Jack Sealey Limited
INSTRUCTIONS FOR:
4 DRAWER RETRO TOP CHEST, 4 DRAWER
RETRO ROLL CAB
AP28104, AP28204
MODEL No's:
Original Language Version
fig.1
fig.2
fig.3
AP28104,AP28204 Issue: 1 - 30/07/14