Wall Mounting; Assembly And Adjustments; Operation - Craftsman CMCE001 Instruction Manual

English
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 °C – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.

Wall Mounting

These chargers are designed to be wall mountable or to
sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet,
and away from a corner or other obstructions which may
impede air flow. Use the back of the charger as a template
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
Versatrack™
CRAFTSMAN chargers can be mounted to the wall using
CRAFTSMAN Versatrack™ Trackwall. Hooks and accessories
are sold separately. Please refer to the Versatrack™ Trackwall
accessory sheet for further information.
Intended Use
This fan is intended for household use
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
6
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source and remove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental can
cause injury.
Suspending/Mounting the Fan (Fig B)
Keyhole Slots
If using the keyhole slots
1"(25.4mm) long with a screw head diameter of 0.24"–0.35"
(6-9mm), one on each side, screwed into a sturdy surface to
an optimal depth leaving approximately 7/32"(5.5mm) of
the screw exposed.
1. Place the wide portion of the keyhole slot over the head
of the screw.
2. Slide the fan down until the screw is inside the narrow
portion of the keyhole and check to be sure the fan
is secure.
Fig. B
7
Carrying the Fan (Fig. A)
Carry the fan using the fan handle
Adjusting the Fan Angle (Fig. A)

WARNING: Keep fingers away from the front and rear
grill of the fan.
This fan has a pivot nut
6
To adjust the fan angle, loosen the pivot nut and gently
push or pull the fan handle

OPERATION


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source and remove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental can
cause injury.
7 , use at least 2 screws at least
7
4 .
for maintaining multiple angles.
4 .