Sealey DCD110V Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
‰
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate
safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend
that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a
supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by
contacting your Sealey stockist.
You must also read and understand the following instructions concerning electrical
9
safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if
used on business premises, are tested by a qualified electrician, using a Portable
Appliance Tester (PAT), at least once a year.
The Health & Safety at Work Act 1974 makes owners of electrical appliances
1.1.2.
responsible for the safe condition of those appliances and the safety of the appliance
operators. If in any doubt about electrical safety, contact a qualified electrician.
Ensure that the insulation on all cables and on the appliance is safe before connecting
9
it to the power supply.
Ensure that cables are always protected against short circuit and overload.
9
Regularly inspect power supply cables and plugs for wear or damage and check all
9
connections to ensure that none are loose.
Ensure that the voltage marked on the appliance matches the power supply to be
9
used.
DO NOT pull or carry the appliance by its power supply lead.
8
DO NOT pull the plug from the socket by the power cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Immediately have any
8
faulty item repaired or replaced by a qualified electrician.
Ensure the unit is correctly earthed via a three-pin 110V plug.
9
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'PE'.
b) Connect the BROWN live wire to the live terminal 'L/+'.
c) Connect the BLUE neutral wire to the neutral terminal.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation extends
past the cable restraint and that the restraint is tight.
1.2. GENERAL SAFETY
Disconnect the drill from the mains power before changing accessories, servicing or performing any maintenance.
9
Maintain drill in good condition. Check moving parts and alignment and keep drill bits sharp. If necessary use an authorised service
9
agent.
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
9
warranty.
Wear approved safety eye protection with side shields and a dust mask if drilling generates dust. Rubber gloves are recommended
9
when using outdoors and safety gloves when drilling items such as steel, brick work etc.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
9
Use drill in an adequate working area for its function, keep area clean, tidy and free from unrelated materials and ensure adequate
9
lighting.
Prevent body contact with grounded surfaces to avoid electric shock i.e. pipes, radiators, ranges, refrigerators etc.
9
Evaluate your working area before using the drill i.e. ceiling, floors and enclosures may contain hidden electrical wires or water
9
piping.
Maintain correct balance and footing.
9
The supplementary handle grip should always be attached for use.
9
Keep children and unauthorised persons away from the working area.
9
Secure non stable work piece with a clamp, vice or other adequate holding device.
9
© Jack Sealey Limited
110V DIAMOND CORE DRILL
MODEL NO:
Wear protective Wear safety
gloves footwear
Original Language Version
DCD110V
Wear protective Wear ear
clothing protection
Wear a mask
DCD110V Issue 3 (3) 27/07/2020