Related Manuals for Modena Fresco Series
Summary of Contents for Modena Fresco Series
- Page 1 User Manual Book Slim Hood Fresco Series SX 9502 V, SX 9502 S, SX 6501 V SX 6501 S, SX 9512 L, SX 7511 L Forte Series SX 9122 L, SX 9002 S, SX 7121 L, SX 6001 S...
- Page 2 Thank you for your trust in choosing MODENA products for your household needs. With your satisfaction as our priority, we constantly aim to deliver stylishly designed products equipped with state-of-the-art technology to assist you in your daily activities. This is your guidebook containing everything you need to know about our product. Please reach out to us if you need further assistance or other information via our Customer Care or our official website www.modena.com.
-
Page 3: Table Of Contents
CONTENT PAGE Introduction • Part 1 : Safety Warnings • Part 2 : Name of Parts • Part 3 : Installation • Part 4 : How to Use • Part 5 : Maintenance • Part 6 : Problem & Solution •... - Page 4 Before connecting the unit to a power source, make sure the power cord is in good shape. If there is damage to the power cord, the replacement must be performed by qualified personnel or contact the MODENA Service Center for replacement process.
-
Page 5: Part 2: Name Of Parts
Part 2: Name of Parts SX 6501 S, SX 6501 V, SX 9502 S, and SX 9502 V The image is a general overview and is not necessarily the same as the product you receive. Features and completeness depends on the type of products SX 9512 L and SX 7511 L Carbon Filter Direction knob... -
Page 6: Part 3: Installation
Part 3: Installation SX 6501 S, SX 6501 V, SX 9502 S, and SX 9502 V Exhaust hood is an equipment which sucks smoke and cooking fragrance. With a vent hood, your kitchen will be free from oil particles that may produce bad odor. Check the strength of wall on which the exhaust hood is to be installed. - Page 7 5. The exhaust hood has two holes on it: Hole D and Hole E (look at the picture). To install the spigot/flange and hole cover, follow these instructions: • For ducting / exhaust system: Install the spigot / flange G on one of the air holes, either D or E. Holes which do not have spigot / flange shall be covered with Hole Cover H.
- Page 8 Connect the exhaust system with the spigot / flange if the exhaust hood is to be operated as a ducting / exhaust system. OPERATING PROCEDURE MODENA Exhaust Hood has 2 (two) work methods as follows:: DUCTING / EXHAUST System: •...
- Page 9 Electricity Connection MODENA Exhaust Hood is designed for 220 volt electricity input, single phase with 50 Hz of frequency. This appliance uses a double-insulated power cord (2 parallel cords) and should not be connected to a grounding wire.
- Page 10 Install the hood at the wall that already pair 2 screws by hange on the screws. When the exhaust hood is positioned correctly on the wall, tighten both screws on the upper part. To reinforce the exhaust hood handle on the wall, install the screws on both holes on the bottom part and tighten them.
- Page 11 Working Method MODENA hoods have 2 version of working method, that is Ducting/Exhaust System: In this mode, the exhaust hood operates by sucking the smoke / cooking odor and then discharging it out of the vent. A heat / fire-resistant ducting system is required to discharge smoke / odor out of the vent.
-
Page 12: Part 4: How To Use
Overall installation should be performed by a competent person in the field of electrical or able to do the installation. If you will do the installation yourself, it is recommended that at first consult to the Service Center Modena. Details of the method and frequency of cleaning listed in the "Installation and Maintenance"... -
Page 13: Part 5: Maintenance
HIGH motor speed SX 9512 L and SX 7511 L • Connect the power cord with an electrical outlet. • Slide or press the motor speed regulator button and light switch to turn vent hood on or off as shown in the following picture. - Page 14 SX 6501 S, SX 6501 V, SX 9502 S, and SX 9502 V MODENA Exhaust Hood is specifically designed for long-term usage and doesn't require complicated maintenance. However, there are several things you can do to maintain its quality as follows:...
- Page 15 Cleaning the Filter: Smoke / steam from cooking and oil particles generated by the cooking procedure will be immediately absorbed by the filter and therefore must be cleaned regularly. Aluminum Filter and Metal Filter: • For routine usage, clean the aluminum filter once every 10 – 15 days by soaking the filter in a basin filled with soap warm water during 1 hour and use a soft brush to clean it and then dry the filter thoroughly before returning it to its proper position.
-
Page 16: Part 7: Precaution
Periodically inspect the filter and oil reservoir. Make sure that the filter is in clean and good condition and make sure the oil reservoir is not exceeding the specified limit. ● If you smell burnt / burnt smell from the hood, immediately turn off the hood and contact the MODENA Service Center. ●... - Page 17 12/20 Cabinet Material Metal Stainless Stainless Front panel’s color Silver (V) Stainless (S) Stainless (S) Motor Lamp Control panel Push Button Push Button Push Button Ionizer Carbon Filter + Carbon Filter + Carbon Filter + Cassette Aluminum Cassette Cassette Filter type Aluminum Filter Aluminum Filter Filter...
- Page 18 12/20 Weight (kg)
- Page 19 12/20...
Need help?
Do you have a question about the Fresco Series and is the answer not in the manual?
Questions and answers