Related Manuals for Allmatic HYPER 400
Summary of Contents for Allmatic HYPER 400
- Page 1 HYPER Ambidextrous irreversible operator for swing door gates. 6-1624982 - ENGLISH - rev.1 - 20/05/2021...
-
Page 2: Table Of Contents
INDEX 1. GENERAL SAFETY WARNINGS 2. DESCRIPTION 3. LIST OF PACKAGING, ACCESSORIES AND OVERALL DIMENSIONS 4. PRODUCT VIEW AND TECHNICAL CHARACTERISTICS 5. PRELIMINARY CHECKS 6. INSTALLATION 7. DECLARATION OF CONFORMITY 8. MAINTENANCE 9. PRODUCT DISPOSAL 10. WARRANTY 2 / 16 6-1624982 - rev.1 - 20/05/2021... -
Page 3: General Safety Warnings
Before installing the product it is mandatory to read the document related to the GENERAL SAFETY WARNINGS accompanying the product. Document 6-1620001. The additional sheet can also be downloaded from www. allmatic.com. 2. DESCRIPTION Ambidextrous irreversible gearmotor for swing gates with doors up to 4.5 m long and up to 300kg. -
Page 4: List Of Packaging, Accessories And Overall Dimensions
3. LIST OF PACKAGING, ACCESSORIES AND OVERALL DIMENSIONS HYPER HYPER Gearmotor for gates with hinged doors complete with assembly kit consisting of: fixing brackets, capacitor, unlocking key and Gearmotor for gates with hinged doors complete with assembly kit consisting of: fixing brackets, capacitor, unlocking key and hardware fasteners. - Page 5 ø 10.5 ø 10.5 ø 10.5 ø 11 ø 11 WITHOUT INTERNAL MECHANICAL STOPPERS 790 (HYPER 400) 990 (HYPER 600) WITH INTERNAL MECHANICAL STOPPERS (1 or 2) 810 (HYPER 400) 1010 (HYPER 600) 6-1624982 - rev.1 - 20/05/2021 5 / 16...
-
Page 6: Product View And Technical Characteristics
Fixing point for front bracket Motor supply cable Screws for adjusting internal mechanical stoppers (op- Key to unlock tional) Release lever to unlock TABLE 2 - HYPER 400 technical characteristics TECHNICAL CHARACTERISTICS U.M. HYPER 400 Recommended control board BIOS2 24... - Page 7 HYPER 400 230Vac WARNING! In the graph next to it is reported, as an explanatory example, the relationship between weight and length of the door for the gearmo- tor HYPER 400 230vac. 6-1624982 - rev.1 - 20/05/2021 7 / 16...
-
Page 8: Preliminary Checks
5. PRELIMINARY CHECKS ZONE OF ENTRAPMENT INTERNAL SIDE OF ZONE OF ENTRAPMENT THE PROPERTY WARNING! It is mandatory to conform the characteristics of the gate to the rules and laws in force. The door can be automated only if it is in good condition and complies with EN 12604. - The door shall not have pedestrian doors. - Page 9 Via dell'Artigianato 1 DENOM 32026 -Borgo Valbelluna (Bl) tel. +39 0437 751175 fax +39 0437 751165 info@allmatic.com - www.allmatic.com Il presente disegno è di proprietà della DUCT Prepare on the installation site the ducts for the passage of motor cables.
- Page 10 5.3 ADVICE ON INSTALLATION WHAT YOU CAN DO: • Ensure that the motor is installed on level. • The motor shall be installed at least 50 mm from the lower edge of the gate door. • The motor can be installed at the top of the gate door. •...
-
Page 11: Installation
Keep in mind that values may vary slightly and must be checked in advance. TABLE 7 - HYPER 400 Recommended installation dimensions W ( α ) 980 (110°) - Page 12 6.2 DETERMINE THE INSTALLATION MEASUREMENTS (OUTWARD OPENING) Before fixing the supplied brackets it is necessary to determine the installation dimensions A and B. Start by putting the gate in position of "OPEN DOOR". Choose the sizes of A and B from Tables 7 and 8 of the previous paragraph, according to your installation and in order to obtain the desired degree of opening "α".
- Page 13 6.3 FASTEN THE REAR BRACKET TO THE COLUMN Attach the rear bracket to the column in accordance with the agreed dimensions. WARNING! In determining the height from the ground to which the bracket is fixed on the pillar, take into account that the brackets for anchoring the piston to the gate shall be fixed at the same level, and that the motor shall be installed at least 50mm away from the lower edge of the gate door.
- Page 14 6.5 ADJUSTMENT OF INTERNAL MECHANICAL STOPPERS (OPTIONAL) MAGNET MECHANICAL STOP OF OPENING MECHANICAL STOP OF CLOSING To adjust the internal mechanical stoppers (optional), proceed as follows: Unlock the motor and manually open the gate to the position of "OPEN DOOR". Approach a magnet (not supplied) or one of the washers provided in the kit on the motor body at the opening mechanical stopper until you find the point where it remains attached.
-
Page 15: Declaration Of Conformity
NEUTRAL Yellow / Green Ground GROUND 7. DECLARATION OF CONFORMITY Manufacturer: Allmatic srl Address: Via dell’Artigiano, 1 - 32026 Borgo Valbelluna (BL) Italia Telephone: +39 0437 751175 E-mail: info@allmatic.com Web site: www.allmatic.com Declares that the HYPER product complies with the provisions of Community Directives:... -
Page 16: Product Disposal
The liability of the manufacturer for damage caused to anyone by accidents of any nature caused by our defective products, are only those that derive from the Italian law. ALLMATIC S.r.l 32026 Borgo Valbelluna - Belluno – Italy Via dell’Artigiano, n°1 – Z.A. Tel. 0437 751175 – 751163 r.a. Fax 0437 751065 www.allmatic.com - E-mail: info@allmatic.com...
Need help?
Do you have a question about the HYPER 400 and is the answer not in the manual?
Questions and answers