Table of Contents
Related Manuals for Backyard Creations Conley
Summary of Contents for Backyard Creations Conley
- Page 1 Owner’s Manual Conley 10’ x 10’ Gazebo with Awning and Bar Model Number: CON-1010-21 SKU Number: 272-1939 Note: This gazebo frame is designed to be used as a permanent fixture. Remove the main canopy and awning when not in use or during high winds, rain or snow.
- Page 2 Parts List 10’ x 10’ Gazebo with Awning and Bar Letter Illustration Description Qty. Main Roof Connector Upper Roof Connector Upper Roof Support Finial Main Roof Corner Support Main Roof Corner Support Extension Main Roof Side Support Cross Beam Cross Beam Cross Beam Cross Beam 2 of 19...
- Page 3 Letter Illustration Description Qty. Corner Post Corner Post Corner Post U-Shaped Connector Cross Beam Corner Plate Cross Beam Center Connector Plate Bar Shelf Bar Support Stand Bar Connector Awning Frame - Left Side Awning Frame - Right Side Awning Corner Connector 3 of 19...
- Page 4 Letter Illustration Description Qty. Awning Frame - Left (Front and Back) Awning Frame – Right (Front and Back) Awning Frame – Center Awning Hydrolic Rod Awning Lock Base Plate Base Cover Main Roof Canopy Upper Roof Vent Canopy Awning Canopy M6 x 15 mm Bolt with Washer M6 x 32 mm Bolt with Nut and Washers 4 of 19...
- Page 5 Letter Illustration Description Qty. M6 x 50 mm Bolt with Nut and Washers M6 x 15mm Bolt with Washer M6 Hex Wrench Allen Wrench Ground Stake Accessory Hook 5 of 19...
- Page 6 Assembly Instructions 10’ x 10’ Gazebo with Awning and Bar Note: For video instructions please visit: https://insideout.store/video-assembly-instructions/ Important: Read all the instructions before assembly. Failure to do so may result in faulty assembly and ⚫ potential injury. ⚫ Before assembling the product, remove all protective materials, hardware kit(s), and identify all parts packed in the carton are present.
- Page 7 Step 2: Insert Cross Beam Center Connector Plate (G) into Cross Beam (D/D1) using Bolt and Washer (R). Repeat for remaining cross beams (D/D1). Insert Cross Beam Center Connector Plate (G) into Cross Beam (D2/D3) using Bolt and Washer (R). See Figure 2. Tighten Bolts. 7 of 19...
- Page 8 Step 3A: Attach Cross Beams (D/D1) to Corner Posts (E/E) using Bolt and Washer (R). Repeat for corner Posts (E/E1) and (E/E2). See Figure 3 and Figure 4. DO NOT TIGHTEN BOLTS UNTIL AFTER STEP 4 Step 3B: Attach Cross Beams (D2/D3) to Corner Post (E1/E2) using Bolt and Washer (R). See Figure 3 and Figure 4.
- Page 9 Step 4A: Connect the U-Shaped Connector (F) to the top of the Corner Posts using Bolt and Washer (U). Repeat for three remaining corner posts. See Figure 5.1. Step 4B: Connect the U-Shaped Connector (F) to the center of the Cross Beams using Bolt and Washer (U). Repeat for three remaining Cross Beams.
- Page 10 Step 5A: Screw the Accessory Hook (Y) into the Main Roof Connector (A). Insert the Main Corner Roof Support (B) into Main Roof Connector (A) until the "push button" lock clicks. Repeat for the three remaining Main Roof Corner Supports (B). See Figure 7. Step 5B: This step requires two people.
- Page 11 Step 6: Insert Main Roof Side Support (C) into the Main Roof Connector (A) until the "push button" lock clicks. Attach the opposite end of the Main Roof Side Support (C) to the U-Shaped Connector (F) in the center of the cross beam using Bolt, Nut, and Washers (S). Repeat for three remaining Side Supports (C).
- Page 12 Step 7: Connect the Bar Connector (H2) to the Corner Post (E1/E2) and tighten with Bolt and Washer (R). See Figure 11. TIGHTEN BOLTS. Step 8: Using two people connect one end of the Bar Shelf (H) to Bar Connector (H2) using Bolt and Washer (R).
- Page 13 Step 9: Assemble Upper Roof Frame: Insert Upper Roof Support (A2) to Upper Roof Connector (A1) until "push button" lock clicks. Repeat for three remaining supports. Attach Upper Roof Vent Canopy (P1) to the upper roof frame. See Figure 14. Screw the Finial (A3) into the upper roof frame.
- Page 14 Step 10A: Place Main Roof Canopy (P) over main roof frame. Note: The Main Roof Canopy (P) has two "open" corner seams. The "open" corner seams are placed over Corner Posts (E1/E2). Do not secure the Main Roof Canopy (P) until the upper roof frame is installed.
- Page 15 Step 11A: Secure the Main Roof Canopy (P) to the four Main Roof Corner Support Extensions (B1). See Figure 17. Step 11B: Secure the Main Roof Canopy (P) to the four Main Roof Side Supports (C). See Figure 18. Note: Canopy will be tight once secured to the roof frame. 15 of 19...
- Page 16 Step 12: Awning Assembly Note: Assemble awning frame before attaching awning canopy (Q). Step 12A: Attach Left Awning Frame (I) to Back Awning Frame (J) with Bolts and Washers (R). Repeat for Right Awning Frame (I1) and Back Awning Frame (J1). See Figure 19. Step 12B: Attach Back Awning Frame (J) to the Back Awning Frame (J1) and the Center Awning Frame (K) with Bolts and Washers (R).
- Page 17 Step 13: Using two people attach assembled awning to gazebo. Step 13A: Connect the back of awning to Corner Posts (E1 and E2) using Bolt, Nut and Washer (T). See Figure 23.1. Step 13B: Connect one end of the Awning Hydrolic Rod (L) to Corner Post (E1) and the opposite end to awning frame using Bolts and Washers (R).
- Page 18 Step 14: Insert four Stakes (X) into the ground through the Base Plate (N). Repeat for each corner. See Figure 25. Note: Please see our video for additional assembly assistance: https://insideout.store/video-assembly-instructions/ 18 of 19...
- Page 19 Care & Maintenance Maintain your outdoor gazebo by removing the canopies and storing out of the elements when not in use, or during hazardous weather conditions (wind, rain, snow, etc.). Frame: Clean frames with a mild soap and warm water. Do not use abrasive materials, cleaners or bleach. Rinse with clean water and dry thoroughly.
Need help?
Do you have a question about the Conley and is the answer not in the manual?
Questions and answers
How do I order replacement parts from comely for my gazebo