Sealey SG10.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! Turn off, or disconnect from air supply before servicing or performing any maintenance and when unit is not in use.

WARNING! This shot blasting kit will generate gritty dust which could damage surface finishes and contaminate moving parts. It is

recommended that shot blasting be carried out in a dedicated room free from unrelated materials, and where there is adequate lighting.
Where this is not possible consideration should be given to covering exposed surfaces and masking moving parts as necessary.
WARNING! Wear approved ear, eye, hand and respiratory protection when operating the blaster. A full range of personal safety

equipment is available from your Sealey dealer.
Maintain correct balance and ensure firm footing by wearing non slip shoes.

Spillages of abrasive material, which may be slippery, must be cleaned up

immediately to avoid injury.
Maintain the blaster in good condition (use an authorised service agent).

Replace or repair damaged parts. Use recommended parts only. Unauthorised parts

may be dangerous and will invalidate the warranty.
Keep the unit clean for best and safest performance.

Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery,

and contain long hair.
Always keep the blast nozzle directed at the workpiece.

If a failure or malfunction occurs immediately disconnect from air supply.

Keep all other persons away from the working area. Contact with high pressure

blast or inhaling the dust generated is dangerous. If other personnel are required in
the vicinity of the shot blasting then they must wear protective equipment similar to
the operator's.
DO NOT use the blaster for any purpose other than that for which it is designed.

DO NOT attempt to clear a blocked nozzle while the unit is pressurised.

DO NOT allow untrained persons to operate the blaster.

DO NOT leave the blaster operating unattended.

DO NOT stand on the blaster.

DO NOT direct air from the air hose at yourself or others.

DO NOT operate system with air supply exceeding 100 psi.

DO NOT operate the blaster if any parts are missing or damaged as this may cause

failure and/or personal injury.
DO NOT get the blaster wet or use in damp or wet locations or areas where there is condensation.

DO NOT operate the blaster when you are tired, under the influence of alcohol, drugs or intoxicating medication.

DO NOT use any abrasive which contains free silica, as indicated in the Health & Safety Guidance Note EH59 (available from HMSO).

2. INTRODUCTION & SPECIFICATION
2.1. Introduction
The SG10.V2 and SG12 sand blasting guns are suitable for use in the body shop.The feathering action of these blasters makes them
especially good for treating stone chips. The SG12 features a forced air recirculation system. Both models are supplied with a set of
rubber nozzles for sealing the gun head to the panel. Sets of spare nozzles are also available.( Part no. SG10/ACC)
2.2. Specifications
Model No. .....................................SG10.V2
Air Pressure ..............................90 to 100psi
Air consumption. ....................... 10 to 15cfm
Max blast Ø. ...................................... 18mm
2.3. Abrasives We recommend the use of Sealey Blasting Grit, part nos. B/25KG ( 25kg bag ) or SG10/SAND6 ( 6 X 700g pots ).
3. AIR SUPPLY
WARNING! Ensure the air supply does not exceed 100psi

while operating the unit. Too high an air pressure will
shorten the life of the unit due to excessive wear and may
cause damage and/or personal injury.
3.1. Ensure the gun trigger is in the 'Off' position before connecting
to the air supply.
3.2. Where possible the compressor should be sited in a separate
room with the connecting airline kept as short as possible.
The compressor should have an air filter and water separator (fig.1).
3.3. Drain the compressor air tank daily. Water in the air line will damage the unit.
3.4. The recommended hook-up procedure is shown in fig.1.
3.5. The minimum hose diameter should be 1/4" I.D. and fittings must have the same inside dimensions.
3.6. Use correct hoses and fittings. DO NOT use quick change couplings as they add weight and can cause failure due to vibration. Add a
leader hose and connect coupling between this and supply hose.
3.7. Keep hoses away from heat, oil and sharp edges. Check hoses for wear and ensure that all connections are secure.
INSTRUCTIONS FOR:
SHOT BLASTING GUNS
MODEL No's:
Model No. ...........................................SG12
Air Pressure ............................. 90 to 100psi
Air consumption. ....................... 12 to 15cfm
Max blast Ø. ....................................... 21mm
fig.1
Original Language Version
SG10.V2 & SG12
SG10.V2, SG12 Issue: 2 - 19/10/09