Fantini Cosmi Intellitherm Techno D C56 Manual

Intellitherm C56
ADVANCED
MONITORING HOW MANY HOURS THE HEATING STAYS ON
22 22 24 24 2 2
C C 4 4
20 20
18 18 6 6
DAY DAY
16 16 8 8
14 14 12 12 10 10
MINIMUM AND MAXIMUM ROOM TEMPERATURE ON THE PREVIOUS DAY
22 22 24 24 2 2
20 20 C C 4 4
18 18 6 6
DAY DAY
16 16 8 8
14 14 12 12 10 10
4 Read the time when said MINIMUM or MAXIMUM temperature was
recorded
SUMMER - AIR CONDITIONING OPERATION
When you move the switch I to the
switches to operating the AIR CONDITIONING system. The red knob is used for
adjusting the comfort mode temperature required in the room, while the economy
I
and antifreeze modes are disabled.
The red sectors on the ring appearing on the display consequently indicate the
hours when the air-conditioning system is in operation, while the sectors in any
other color indicate when it is off.
TELEPHONE ACTIVATOR
Intellitherm C56 has been designed for combining with the CT5 telephone
activator. This accessory enables remote control of the temperature controller by
means of a normal telephone line. The CT5 telephone activator is equipped with a
voice synthesizer that enables its immediate and straightforward use. It also enables
remote monitoring of the room temperature and of the proper operation of the
temperature controller.
CT5 even enables the remote control of virtually any other electrical appliance
(sprinklers, household appliances, etc.).
TECHNICAL FEATURES
- In compliance with the CEI EN 60730-1 and parts two
- Terminal carrying capacity 8 (5) A 250 V ac
- Micro-disconnection (1BU)
- Co-load switching contact
- Temperature control:
- comfort from 2 to 62 °C
- economy from 2 to 62 °C
- Differential ± 0.25 °C
- Reference thermal gradient 4° K/h
- OFF mode with optional antifreeze protection (5 °C)
selected by means of a dip switch
-
double insulation
We reserve the right to make any technical and structural changes deemed necessary without .
FUNCTIONS
With Intellitherm C56, you can keep a check on how many
hours the heating has actually been on (relay closed - ON) on
the previous day or since the temperature controller was last
enabled (i.e. since the last time the batteries were changed or
the device was reset).
1
S
Move the switch S to the position
P 2
Move the switch P to the PROG position
3 Read the hours of heating on the previous day
Read the hours of heating since the controller was
4
enabled.
With Intellitherm C56 you can also keep a check on
the MINIMUM and MAXIMUM temperatures
recorded in the room on the previous day and the time
when they occurred.
Move the switch S to the (economy) position
1
for the MINIMUM temperature or to the
S
(Comfort) position for the
temperature
2
P
Move the switch P to the PROG position
3
Read the MINIMUM or MAXIMUM room temperature
SUMMER position, Intellitherm C56
- Protection grade IP 20 (normal pollution)
- Powered by 2 alkaline AA 1.5V pencil Batteries,
with no connection to the mains
- Battery life two years approx.
- Automatic monitoring of battery charge with
signal on display when battery is low
- Battery changing without losing previously-
memorized programs
-
Switch for summer/winter operating modes
-
Reset button for restoring standard program
-
Overall dimensions: 120 x 80 x 27 mm
Intellitherm Techno D - C56
DAILY TEMPERATURE CONTROLLER
1 - WALL MOUNTING
Intellitherm C56 is supplied complete with a base
suitable for mounting flush in a rectangular three-
module or a round outlet box, or for attaching to the
wall.
Fit the controller 1.5 m above floor level, well away
from kitchens, sources of heat, doors or windows.
Make sure that the base is attached on a level and
without any straining.
MAXIMUM
2 - ELECTRIC CONNECTIONS
Connect terminals 1 - 2 to the heating system with two
wires, replacing the conventional thermostat at any
time, without adding any further connections. When
the room temperature increases, the relay
terminals 1 - 2and closes 1 - 4
Terminal 4 is free and can be used for signals or other
purposes.
3 - SELECTING THE OFF MODE
During periods when it is OFF, Intellitherm can be set
to maintain a temperature setting of 5°C to protect the
system from the risk of freezing.
If you require such ANTIFREEZE protection, position
the dip switch (situated at the bottom left-hand side on
the back of the body of the C56) on HIGH. If, on the
other hand, you want the system to be switched OFF
completely, position the dip switch on LOW .
This selection must be made at the time of installation
and before fitting the batteries.
NOTE: if, at any time after installation, you wish to
change this selection, the Intellitherm must be
reset and reprogrammed.
4 - FITTING THE BODY OF THE TEMPERATURE
CONTROLLER ON THE BASE
5 - FITTING THE BATTERIES
Insert two good-quality, alkaline long-life AA 1.5 V
pencil batteries in the space provided, taking care to
comply with the polarity indicated. The batteries can
last about two years; when they begin to run down,
the battery symbol on the display starts to flash
If the batteries are not changed within 15 days,
Intellitherm C56 will automatically switch off and only
the word OFF will appear on the display.
Via dell'Osio, 6 20090 Caleppio di Settala MI - ITALY
International calls Tel. ++39 02 95682222
Fax +39 02 95307006
E-mail: export@fantinicosmi.it http//www.fantinicosmi.com
DISTANCE BETWEEN CENTERS FOR
FIXING THE BASE
B -
60 mm
A -
83,5 mm
TERMINAL BOARD AND CONNECTIONS
opens
.
2
4 1
SELECTING THE OFF OR OFF+ANTIFREEZE
PROTECTION MODES
FITTING AND CHANGING THE BATTERIES
Lift the cover and fit two 1.5V batteries
.
22 22 24 24
20 20
18
A = for rectangular
flush-mounted boxes
type 503 (three
modules)
B = for round flush-
mounted boxes
L O O S E N T H I S
SCREW AND TURN
THE BODY OF THE
C O N T R O L L E R
U P W A R D S T O
DETACH THE BASE
FOR FIXING TO THE
WALL.
2 1 4
ANTIFREEZE (5°C)
OFF
-
+
2 2
C C 4 4
6