Table of Contents
Advertisement
High quality, license-free, ultra-tiny VTX
The TBS UNIFY PRO32 is a successor to the most popular line of video transmitters (TBS UNIFY PRO). We
have improved the robustness, decreased the size and power consumption, added capability for insane
features and perfected the way it is installed in your multirotor. In a nutshell, it's the most comprehensive,
future proof, highest quality and overall best VTX line made to date.
Key features: Main features across all Unify Pro32 models
•
World's lightest 37ch video transmitter line (custom channels via Smartaudio and CRSF)
•
Power to Channel calibration for each channel - extremely consistent output power
•
25mW (more power available, requires HAM license*)
•
One button frequency and power setup
•
OSD configuration using TBS SmartAudio 2.1 (via FC, TBS Crossfire/ Tracer or PNP PRO OSD)
•
LUA support for CRSF users
•
U.FL connector (Unify PRO32 nano)
•
MMCX connector (Unify PRO32 HV)
•
1-3S input or 2-6S input with 5V output versions available
•
Improved noise filtering
•
Double noise filtering (Unify PRO32 HV)
•
Optimized heat dissipation
•
Solder-on module dimensions available on request
1
Revision 2021-03-29
Advertisement
Table of Contents
Summary of Contents for Team Blacksheep TBS UNIFY PRO32 5G8 nano
- Page 1 High quality, license-free, ultra-tiny VTX Revision 2021-03-29 The TBS UNIFY PRO32 is a successor to the most popular line of video transmitters (TBS UNIFY PRO). We have improved the robustness, decreased the size and power consumption, added capability for insane features and perfected the way it is installed in your multirotor.
- Page 2 Smart Audio or CRSF for the VTX? Button not working Control by PWM channel (Unify PRO32 Nano only) Video transmitter pinout TBS UNIFY PRO32 5G8 nano TBS UNIFY PRO32 HV 5G8 Barcode Control Technology showcase ...
- Page 3 Force device into bootloader mode Specifications TBS UNIFY PRO32 5G8 nano TBS UNIFY PRO32 HV (MMCX) Input voltage: 1S - 3S LiPo 2S - 6S LiPo 3V - 13V ...
- Page 4 * requires HAM license, special unlocking procedure, available on selected models only! Attention These video transmitters are capable of radio frequency transmissions and output power that may be not allowed in your country. Please always check your local RF legislation to set the frequency and output power according to ...
- Page 5 Overview Nano32 Pro32 5 ...
- Page 6 Button menu control The menu consists of categories and settings. Pressing the button for 3 seconds will toggle between categories, pressing it for a short time toggles between settings. To enter the menu, hold the button for 3 seconds.
- Page 7 7 ...
- Page 8 For Unify PRO32 Nano The TBS UNIFY PRO32 5G8 signals selected channel, band and power levels using a startup sequence of LED codes. The same sequence is also repeated in the menu to make it unified. First the LED flashes to ...
- Page 9 Channel/ Band - Frequency Table Channel 1 2 3 4 5 6 7 8 Band A 5865 5845 5825 5805 5785 5765 ...
- Page 10 TBS UNIFY PRO32 automatically reduces output power before it reaches critical heat levels. Pinout TBS UNIFY PRO32 5G8 nano The UNIFY PRO32 5G8 Nano comes with pre installed silicon wires for easy installation in your build. There ...
- Page 11 TBS UNIFY PRO32 HV 5G8 The UNIFY PRO32 5G8 HV comes with a cable assembly with silicon wires for easy installation in your build. There is a filtered 5V output for your camera. The installed Step Down converter is a new, more powerful DCDC and is capable of powering most 5V ...
- Page 12 Control by Flight Controllers (Smartaudio) Using any Smart Audio V2.1 compatible flight controller simply connect the Smart Audio data pin to a free and supported port on your FC (see pinout below). For Betaflight users, you can then configure the connected port in Betaflight configurator to Smart Audio V2.1 protocol.
- Page 13 Crossfire/Tracer connection using CRSF All Unify PRO32 do have a full serial interface which has extended functionality compared to Smartaudio which is just a onewire protocol. ● Set the Unify to CRSF by the button ●...
- Page 14 Button not working When the Unify Pro32 detects a signal on the RX pad, it will disable the button. To change the VTX to CRSF or SA, you can unsolder the wire or force your Crossfire/ Tracer RX to not output any signal. Set the output of the Tracer RX to CH X (PWM) for the pin the VTX is connected to ...
- Page 15 Barcode Control The video transmitter can be controlled via barcodes through your camera. This allows you to enable PITMode, and power up your video transmitter by holding the barcode in front of your camera. Or simply to carry your favorite channel in your pocket or on your backpack and revert to that channel easily and ...
- Page 16 ● CRSF CRSF is a protocol designed by Team BlackSheep and championed through the TBS Crossfire remote control system. It has been integrated into most popular remote controls, is an incredibly high bandwidth (low latency) full duplex, serial data transmission protocol. It comes with native functionality such as OTA ...
- Page 17 CleanSwitch A new feature introduced with the TBS UNIFY PRO 5G8 is CleanSwitch. When video transmitters power up or change frequency, they usually send a burst across the entire band which disturbs fellow flying pilots. All UNIFY PRO32 5G8 video transmitters will remain in their lowest power output (less than 0.1mW) while ...
- Page 18 18 ...
- Page 19 Manual designed by ivc.no, written by TBS, ivc.no and kamikatze-fpv.de 19 ...
Need help?
Do you have a question about the TBS UNIFY PRO32 5G8 nano and is the answer not in the manual?
Questions and answers