All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by RB 0262 Service PaCE...
EN 4 L01H.1A Safety & Maintenance Instructions, Warnings, and Notes 2. Safety & Maintenance Instructions, Warnings, and Notes Safety Instructions For Repairs Warnings Safety regulations require that during a repair: • In order to prevent damage to ICs and transistors, avoid all •...
Mechanical Instructions L01H.1A EN 13 4. Mechanical Instructions Index: Main panel with bracket. 1. Rear Cover Removal 1. Disconnect the strain relief of the AC power cord. 2. Service Position Main Panel 2. Disconnect the degaussing coil by removing the cable from 3.
Page 14
EN 14 L01H.1A Mechanical Instructions Side I/O Panel Removal 1. Remove the complete Side I/O assembly after unscrewing the two fixation screws [1]. 2. Release the 2 fixation clamps [2] and lift the board out of the bracket. CL 06532012_004.eps...
Service Modes, Error Codes and Fault Finding L01H.1A EN 15 5. Service Modes, Error Codes and Fault Finding Index: – 61.25 MHz (channel 3) for NTSC set (AP-NTSC) 1. Test points. • Colour system: 2. Service Modes. – PAL-BG for AP-PAL.
Page 16
EN 16 L01H.1A Service Modes, Error Codes and Fault Finding – X = the main software version number. CSM Menu – Y = the sub software version number. 3. S Indication of the actual mode. S= SDAM= Service Default Alignment mode.
Page 17
Service Modes, Error Codes and Fault Finding L01H.1A EN 17 2. Select the INSTALLATION sub menu. 5.3.2 Sound Problems 3. Select and change the SYSTEM setting until picture and sound are correct. No sound or sound too loud (after channel change / 4.
Page 18
EN 18 L01H.1A Service Modes, Error Codes and Fault Finding The Blinking LED Procedure • Set is non-stop in hiccup mode Set is in over current mode; check the secondary sensing (opto coupler 7515) and the MainSupply voltage. Signal Via this procedure, you can make the contents of the error Stdby_con must be logic low under normal operation buffer visible via the front LED.
Block Diagram, Testpoints, I2C, and Supply Voltage Overview L01H.1A 6. Block Diagram, Testpoints, I C, and Supply Voltage Overview Block Diagram UIR/LS 1259 INTERFACE (FOR SYSTEM SETS ONLY) 0240 AUDIO AMPLIFIER FRONT CONTROL CONTROL +3.3V +3.3V DATA-OUT 32 PIN SMART CARD CONNECTOR (FOR 29"...
Block Diagram, Testpoints, I2C, and Supply Voltage Overview L01H.1A Wiring Diagram EPS 4B PANEL TOP CONTROL LEFT FRONT INTERFACE PANEL TOP CONTROL 0254 0215 0255 0211 0215 0214 0212 RIGHT 0219 0231 INTERFACE PANEL 0211 0242 0227 0212 0280 0228...
Block Diagram, Testpoints, I2C, and Supply Voltage Overview L01H.1A Testpoint Overview Main Panel Copper Track side AUDIO OUTPUT 7901 OR 7902 1V / div DC 500mV / div DC 1V / div DC TV-PROC. 20us / div 5ms / div...
Page 22
Block Diagram, Testpoints, I2C, and Supply Voltage Overview L01H.1A I2C And Supply Voltage Diagram POWER SUPPLY SCAVEM LINE DEFLECTION 5445 3362 ANODE CRT +13Va FOCUS FOCUS 5500 : 6500 6560 FOCUS CRT 5560 5564 5561 MAIN SUPPLY 3487 0231 5451...
Page 23
Schematics and PWB’s L01H.1A 7. Schematics and PWB’s Large Signal Panel: Power supply 0211 C2 6500 C7 I539 F11 0212 A2 6520 E2 I540 D9 POWER SUPPLY 0213 C6 6522 E3 I541 E9 VlotAux+13V 2581 0231 C2 6523 D5 I542 C9...
Schematics and PWB’s L01H.1A Large Signal Panel: Control 0217 G3 0240 B4 0250 B3 CONTROL 0261 D3 0273 B5 FOR PIP FOR ITV ONLY 0274 B9 F612 3611 F606 0279 C4 +3.3V 100R 0304 H3 DATA-OUT +3.3V 1660 E8 7602...
Schematics and PWB’s L01H.1A Large Signal Panel: NICAM + 2CS + BTSC (Stereo / SAP Decoder) 0239 G10 1831 C9 2831 C9 2832 C9 2833 D5 2834 B4 2835 B4 NICAM + 2CS + BTSC (STEREO/SAP) DECODER (AP) 2836 B5...
Page 32
Schematics and PWB’s L01H.1A Large Signal Panel: Audio / Video Source Switching 0296 B5 2801 A5 AUDIO/VIDEO SOURCE SWITCHING (AP) 2802 E5 2803 C3 2804 B6 From Micronas 2805 D6 3801 A5 SC2_CTRL 3802 A5 A9-50 I801 3801 +6V8 3803 B5...
Page 33
Schematics and PWB’s L01H.1A Large Signal Panel: Front I/O + Front Control + Headphone 0214 F10 0215 C5 0218-A C3 0218-B C3 0218-C B3 0219 D5 0232 F5 FRONT IO + FRONT CONTROL + HEADPHONE 0259 F11 0270 B6 0277-A B2...
Page 35
Schematics and PWB’s L01H.1A Large Signal Panel: Tilt and Rotation Personal Notes: 0268 C6 2171 D2 2172 D3 3171 C2 3173 C2 3174 C3 TILT & ROTATION 7000 C4 F171 C6 F172 D6 I171 C2 I172 C2 I173 C3 I174 D3...
Page 36
Schematics and PWB’s L01H.1A Layout Large Signal Panel (Top View) CL 16532053_005.eps 050601...
Page 37
Schematics and PWB’s L01H.1A Layout Large Signal Panel (Mapping Top View) Layout Large Signal Panel (Overview Bottom View) Part 1 CL 16532053_06a.eps Part 2 CL 16532053_06b.eps Part 3 Part 4 CL 16532053_06c.eps CL 16532053_06d.eps CL 16532053_006.eps 100701 CL 16532053_05m.eps 100701...
Page 38
Schematics and PWB’s L01H.1A Layout Large Signal Panel (Part 1 Bottom View) Part 1 CL 16532044_06a.eps 240801...
Page 39
Schematics and PWB’s L01H.1A Layout Large Signal Panel (Part 2 Bottom View) Part 2 CL 16532053_06b.eps 310501...
Page 40
Schematics and PWB’s L01H.1A Layout Large Signal Panel (Part 3 Bottom View) Part 3 CL 16532053_06c.eps 040601...
Page 41
Schematics and PWB’s L01H.1A Layout Large Signal Panel (Part 4 Bottom View) Part 4 CL 16530153_06d.eps 050601...
Page 42
Schematics and PWB’s L01H.1A CRT Panel VG2 F10 0165 A8 0244 E2 0245 D2 CRT PANEL 0254-A B7 0255 B7 0256-A B7 AQUADAG 2330 B4 1V / div DC 1V / div DC 1V / div DC 50V / div DC...
Alignments L01H.1A EN 55 8. Alignments Index: 8.2.1 Vg2 Adjustment (AKB method) General Alignment Conditions Hardware Alignments 1. Connect the RF output of a pattern generator to the Software Alignments and Settings antenna input. Test pattern is a 'black' picture (blank screen on CRT without any OSD info).
Page 56
25HT2011/93Z 113 0 ON / OFF 25HT2011/94Z 113 0 WIDESCREEN ON / OFF 25HT2212/67R 113 0 TUNER NONE / APLS / PHILIPS 25HT2212/69R 113 0 ON / OFF 25HT2012/79R 113 0 CHINA ON / OFF 25HT2012/93R 113 0 US REGION CODE...
Page 57
Radio 1 = Tuner has FM radio feature and TV chasis support FM radio 1 = Tuner has LNA feature Tuner 0 = None (no tuner), 1 = Philips (model), 2 = Alps (model) Byte 3 Not Used (Devices) Not Used...
Page 58
EN 58 L01H.1A Alignments 8.3.2 Deflection 8.3.4 White Tone The Deflection Sub menu contains the following items: White Tone Menu • AKB ON to enable, OFF to disable the 'black current loop' (AKB = Auto Kine Bias). • Brightness (set Brightness) •...
Page 59
Alignments L01H.1A EN 59 8.3.5 Geometry • Select East-West Width EW and align the picture width until the side castellations disappear. • Select East-West Parabola / width PW and align the The geometry alignments menu contains several items to align vertical sides until the sides are straightened.
EN 60 L01H.1A Circuit Description 9. Circuit Description Index: 1. Introduction The L01 is divided into 2 basic systems, i.e. mono and stereo 2. Audio Signal Processing sound. While the audio processing for the mono sound is done 3. Video Signal Processing in the audio block of the UOC, an external audio processing IC 4.
Page 61
Circuit Description L01H.1A EN 61 9.2.2 Mono 9.3.3 Video Source Selection In mono sets, the signal goes via the SAW filter (position 1004 The Composite Video Blanking Signal (CVBS) from buffer in case of QSS demodulation and 1003 in case of Intercarrier...
Page 62
EN 62 L01H.1A Circuit Description Also some picture improvement features are implemented in voltage on pin 54 is normally 3.3 V (limiter not active). this part: During set switch-off, the black current control circuit • Black stretch This function corrects the black level of generates a fixed beam current of 1 mA.
Page 63
Circuit Description L01H.1A EN 63 divided by two, to lock the first control loop to the incoming IC7471 is supplied by +13 V. The vertical flyback voltage is signal. determined by an external supply voltage at pin 6 When the IC is switched ‘on’, the ‘Hdrive’ signal is suppressed (VlotAux+50V).
Page 64
EN 64 L01H.1A Circuit Description The ‘Ewdrive’ signal from pin 15 of IC7200 takes care for the correct correction. It drives FET TS7400. It also corrects SUPPLY START-UP V CC breathing of the picture, due to beam current variations (the...
Page 65
Circuit Description L01H.1A EN 65 Degaussing Control Circuit B1/B2 n⋅V Main Supply Focus Mains AC Input Main Power Panel VideoSupply Supply Main Aux Filament Tilt& Rotation GATE Degaussing Circuit VlotAux +13V 3V3 Reg. Correction Horizontal GATE Vaux Deflection +3.9V +3.3V...
Page 66
EN 66 L01H.1A Circuit Description The moment that the voltage on pin 1 drops below the ‘under voltage lock out‘ level (UVLO = ± 9 V), the IC will stop switching and will enter a safe restart from the rectified mains voltage.
Page 67
Circuit Description L01H.1A EN 67 In Standby, the power supply works in ‘burst mode’. Burst mode can be used to reduce the power consumption Active/ below 1 W at stand-by. During this mode, the controller is active inactive (generating gate pulses) for only a short time and for a longer time inactive waiting for the next burst cycle.
Page 68
EN 68 L01H.1A Circuit Description Over Power Protection 9.7.1 Introduction During the primary stroke, the rectified AC input voltage is measured by sensing the current drawn from pin 4 (DEM). This The microprocessor part of the UOC, has the complete control current is dependent on the voltage on pin 9 of transformer and teletext on board.
Page 69
Circuit Description L01H.1A EN 69 • SEL-MAIN-FRNT-RR This is the source select control signal from the microprocessor. This control line is under In case one of these protections is activated, the set will go into user control or can be activated by the other two control ‘standby’.
Page 70
EN 70 L01H.1A Circuit Description Field Memory Sandcastle: pulse derived from sync Frequency Modulation signals Horizontal Acquisition: horizontal sync Short Circuit pulse coming out of the HIP SCAVEM Scan Velocity Modulation Horizontal Flyback Pulse: horizontal Serial Clock sync pulse from large signal deflection...