Sealey LED035.V2 Instructions

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you
years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to the instruction
manual
1. SAFETY
1.1. GENERAL SAFETY.
Ensure the penlight is correctly charged before initial use.

DO NOT turn either light on when it is being re-charged.

DO NOT shine directly into your, other person's or animal's eyes.

DO NOT allow children to use the penlight.

DO NOT use the penlight if you suspect that the battery or the penlight casing is damaged.

DO NOT immerse the penlight in water.

When not in use store the penlight in a safe, dry, childproof location.

1.2. ELECTRICAL SAFETY.
USE ONLY THE SUPPLIED MAINS CHARGER PLUG FOR CONNECTING TO THE MAINS POWER SUPPLY.
WARNING! It is the user's responsibility to read, understand and comply with the following electrical instructions:

You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current Circuit
Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device) is used with
all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3. You must ensure that you:
Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power

supply. If worn or damaged DO NOT use.
Check cables are always protected against short circuit and overload.

Important: Check that the voltage marked on the charger plug is the same as the power supply to be used.

DO NOT pull the charger plug from the mains socket by the lead.

DO NOT use any other type of charger with this product other than desktop computer or laptop (5VDC) USB sockets.

DO NOT place the connector into any area of the spotlight except the correct jack inlet socket.

DO NOT try to take the charger plug apart.

DO NOT use the charger plug to charge or power any other electrical item.

DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only).

2. INTRODUCTION
Small and compact, ideal for keeping in a pocket. Features 5 SMD LEDs for use as an inspection lamp and 1 ultra bright 3W CREE on top for use
as a directional torch. Rechargeable Lithium-ion battery that suffers no memory effect and performs better for longer. Supplied with USB to pin jack
lead and mains charger.
3. SPECIFICATION
Model No:........................... LED035.V2
Battery:................................ 3.7V 2.0Ah Li-ion
LED Quantity:...................... 5 + 1
Lumen Output:..................... 150lm (side lamp)
Lumen Output:..................... 110lm (end torch)
Charging Time:.................... 4hrs
Operating Time:................... 4hrs
Length:................................ 190mm
© Jack Sealey Limited
INSTRUCTIONS FOR:
RECHARGEABLE INSPECTION PENLIGHT
5SMD LED + 3W CREE LED LITHIUM-ION
LED035.V2
MODEL No:
Original Language Version
LED035.V2 Issue: 1 - 06/11/15