Table of Contents
Advertisement
Troubleshooting • Solución de problemas
EN
Problem
Crib toy does not
function
Remote control
does not function
Motion or lights
does not function
ES
Problema
El juguete para
cuna no funciona
El control remoto
no funciona
El movimiento
o las luces no
funcionan
FR
Problème
Le jouet pour
berceau ne
fonctionne pas
La télécommande
ne fonctionne pas
Détection des pannes
Probable Cause / Solution
Remove Try-me pull tab and discard
Check or replace main batteries
Set Power/volume Switch to Low or High
Press Play/start Button on crib toy to activate IR
sensor (Power/volume Switch must not be OFF)
Check or replace batteries in remote control
Move within range of crib toy (12 to 15 ft.)
Select mode that includes lights or motion
Use Play/stop Button to restart playback
Check or replace main batteries
Causa probable / Solución
Retire la lengüeta extraíble TryMe y deséchela
Verifique o reemplace las baterías principales
Configure el interruptor de Encendido/Volumen a Bajo
o Alto
Presione el botón de reproducción/inicio del juguete
para cuna para activar el sensor IR (el interruptor de
Encendido/Volumen no debe estar Apagado)
Verifique o reemplace las baterías del control remoto
Muévase dentro del rango del juguete para cuna (de
12 a 15 pies)
Seleccione el modo que incluye luces o movimiento
Use el botón de Reproducción/Detener para reiniciar la
reproducción
Verifique o reemplace las baterías principales
Cause probable / Solution
Retirer la languette pour le mode Essaie-moi et la jeter
Vérifier ou remplacer les piles de l'unité principale
Placer l'interrupteur de mise en marche/commande du
volume sur Low (bas) ou High (élevé)
Appuyer sur le bouton lecture/début du jouet pour ber-
ceau pour activer le capteur IR (l'interrupteur de mise
en marche/commande du volume ne doit pas être à la
position OFF [arrêt]
Vérifier ou remplacer les piles de la télécommande
Rester dans la portée du jouet pour berceau (de 3,5 à
4,5 m)
– 16 –
See page
3
4
9
10
6
13
9
10
4
Consulte
página
3
5
9
10
6
13
9
10
5
Voir
page
3
5
9
11
6
13
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Sea Dreams Soother and is the answer not in the manual?
Questions and answers
How do I purchase the crib strap and remote?
New Crib aquarium stoped working
To fix a Baby Einstein Sea Dreams Soother that has stopped working, try the following steps:
1. Check the Batteries – Ensure the batteries are properly installed and replace them if they are old or depleted.
2. Inspect the Battery Compartment – Look for any corrosion or dirt in the battery compartment and clean it if necessary.
3. Ensure Proper Attachment – Make sure the soother is securely attached to the crib using the provided straps.
4. Reset the Device – Remove the batteries for a few minutes, then reinstall them to reset the soother.
5. Check the Remote – If using the remote, verify that its battery is functional and replace it if needed.
6. Confirm Sound and Light Settings – Adjust the volume and light settings to ensure they are not turned off.
If the soother still does not work, consult the product manual for further troubleshooting or contact the manufacturer for support.
This answer is automatically generated
Who is the manufacturer for the Baby Einstein aquarium? We have 2 units that are no longer working.
The Baby Einstein Sea Dreams Soother is manufactured by Baby Einstein.
This answer is automatically generated
Music isn't playing
The music may not be playing on the Baby Einstein Sea Dreams Soother for several reasons:
1. Demo Mode: If the unit is new, the demo mode tab may still be in place. Remove it to enable full functionality.
2. Battery Issues: Ensure the main unit has 4 "C" batteries and the remote has 2 "AAA" batteries, and replace them if they are depleted.
3. Standby Mode: The unit enters standby mode after 25 minutes. Press the play button on the main unit or use the remote to restart playback.
4. Remote Signal: The infrared remote needs to be within 3.5 to 4.5 meters (12 to 15 feet) and in a direct line of sight with the soother.
5. Volume Setting: If the volume is too low, adjust it using the volume controls on the main unit.
6. Faulty Unit: If none of the above solutions work, the unit may be defective.
This answer is automatically generated