Related Manuals for volkano Phonic Series
Summary of Contents for volkano Phonic Series
- Page 1 Phonic Series INSTRUCTION MANUAL IMPORTANT: Please read before using this product. VK-2002-BK / VK-2002-GD / VK-2002-BL...
-
Page 2: Specifications
SPECIFICATIONS Bluetooth: Version: V5.0 Chipset: JL-6925 Profiles: AVRCP, A2DP, HFP Range: 10 m Impedance: 64 Ω Frequency Range: 20 Hz ~ 20 kHz Sensitivity: 108 dB Battery: 400 mAh Li-Ion Driver Size: 40 mm Charging Time: 2.5 Hours Charge Input: 5 V DC, 1 A Playtime (at 50% volume): 18 ~ 24 Hours... -
Page 3: Identifying Parts
IDENTIFYING PARTS Power On /Off + Next / Volume Up Play / Pause / Call - Previous / Volume Down 5. M Mode Button: FM Radio / MP3 (Micro SD Card) / Bluetooth 6. Microphone 7. USB Charging Port 8. Aux Input 9. - Page 4 INCLUDED IN THE BOX • Volkano Phonic Bluetooth Folding Headphones • Instruction Manual • USB to Micro USB Cable • 3.5 mm Aux Line Input Cable CHARGING Please ensure that the battery is fully charged before using the device for the first time.
-
Page 5: Connecting With Paired Devices
CONNECTING WITH PAIRED DEVICES • Switch on the headphones. • Press the M Mode Button to switch to Bluetooth Mode. • The red and blue LED lights will flash, this means that the headphone is ready to pair with a Bluetooth device. •... - Page 6 4. FM Mode Function Operation Press the M Mode Button to cycle to FM Mode Enter FM Mode Auto-Scan Long press the Play Button to auto-scan stations Press the + Volume Up / Forward Button to skip a station and continue searching, or - Volume Down / Fine Tune Backward to return to a station.
-
Page 7: Safety Precautions
• The product should only be used with the parts provided by the manufacturer. • This product is intended for indoor use only. • Never use your Phonic Series Headphones near water or in areas where it can come into contact with water. Never handle the Phonic Series Headphones if they have been dropped in water or any other liquid. -
Page 8: Troubleshooting
TROUBLESHOOTING 1. No Power Recharge your Phonic Series Headphones using the included Micro USB Cable. Try using a different Micro USB Cable. 2. Music is not playing over Bluetooth Make sure your Bluetooth device has A2DP profile. Check if both devices are paired and connected over Bluetooth. -
Page 9: Warranty
Use of them does not imply any affiliation with or endorsement by them. WARRANTY These Volkano Phonic Series Bluetooth Headphones include a standard 12-month limited warranty against manufacturing defects and faults. Should your product be unboxed with any faulty parts, poor finishing, visible damage, or fail to perform due to a manufacturing defect or poor workmanship, please return it with your proof of purchase (till slip or invoice) to the store of purchase for an exchange, or repair, depending on the store’s returns policy.
Need help?
Do you have a question about the Phonic Series and is the answer not in the manual?
Questions and answers
Hi my Bluetooth volcano headset not switch on, when chaging the light show of chaging when switch on no light show for switch on
Your Volkano Phonic Series Bluetooth headset may not be turning on and showing no light due to the following reasons:
1. Battery is not charged – Ensure the battery is fully charged before use. Connect the provided USB charger cable to the charging slot and a 5V USB power source. The red LED should light up during charging.
2. Faulty charging connection – Check if the charging cable and power source are working correctly. Ensure the USB charger is properly connected.
3. Battery issue – If the headset does not charge or turn on after charging, the battery may be faulty.
4. Power button issue – Ensure you are pressing and holding the Power button for about 3 seconds until the blue LED flashes.
5. Internal hardware malfunction – If none of the above steps work, the headset may have an internal defect.
Try charging the device and turning it on again. If the issue persists, the headset may need repair or replacement.
This answer is automatically generated
Hi my headphones light switched from red to blue while charging, what does that mean???
When the Volkano Phonic Series headphones are charging, the LED indicator light displays red. When the headphones are fully charged, the LED indicator light flashes twice and then turns off. The light does not switch from red to blue while charging.
This answer is automatically generated
how do you factory reset volcano headphones pebble series on phonic series
My phonic headphones are suddenly not turning on even after charging them
If the Volkano Phonic Series headphones are not turning on after charging, try the following troubleshooting steps:
1. Ensure Proper Charging – Use the included Micro USB cable to charge the headphones. If they do not turn on, try using a different Micro USB cable.
2. Check Battery Status – Make sure the headphones have been charged for a sufficient period.
3. Restart the Headphones – Try powering them off and on again.
4. Inspect for Damage – Ensure there are no visible signs of damage to the charging port or cable.
If the issue persists, the battery or internal components may be faulty.
This answer is automatically generated
How do you shuffle music from the sim card
Good day I want to pair my headphones to my Samsung A35. I was previously paired to my Damsung E21 F I saays I need a pin could you please help me.
To pair Volkano Phonic Series headphones to a Samsung A35:
1. On the headphones:
- Switch them on.
- Press the M Mode Button to enter Bluetooth Mode.
- Wait for the red and blue LED lights to flash (indicates pairing mode).
2. On the Samsung A35:
- Go to Settings > Bluetooth.
- Turn Bluetooth on (if not already on).
- The phone will automatically search for devices. If not, tap “Search for Devices.”
- Select “Phonic” from the list of found devices.
3. Confirm the pairing.
No PIN is needed unless prompted; if prompted, enter "0000".
This answer is automatically generated
Good day I want to pair my Headphones with my Samsung A35 but I need a pin. Could you please help me.
To pair Volkano Phonic Series headphones with a Samsung A35:
1. Turn on Bluetooth on the Samsung A35 by going to Settings > Connections > Bluetooth.
2. Turn on the headphones and press the M Mode button to switch to Bluetooth mode.
3. Wait for the red and blue LED lights to flash, indicating the headphones are ready to pair.
4. On the Samsung A35, search for new Bluetooth devices.
5. Select “Phonic” from the list of available devices.
6. If a PIN is required, enter 0000.
7. When paired successfully, the blue LED on the headphones will flash slowly.
The headphones are now ready to use.
This answer is automatically generated
How can i reset my headphones?