CTM LYNG Mkomfy R-T 25A Installation Instructions User Instructions

Panel-installed cooker guard relay

Advertisement

Quick Links

Installation instructions/User instructions
Mkomfy R-T 25A
Panel-installed cooker guard relay
Mkomfy set with sensor and relay
is supplied ready paired and ready for use
Fulfils the requirements
of NEK 400:2014
SAVE THESE INSTRUCTIONS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Mkomfy R-T 25A and is the answer not in the manual?

Questions and answers

Summary of Contents for CTM LYNG Mkomfy R-T 25A

  • Page 1 Installation instructions/User instructions Mkomfy R-T 25A Panel-installed cooker guard relay Mkomfy set with sensor and relay is supplied ready paired and ready for use Fulfils the requirements of NEK 400:2014 SAVE THESE INSTRUCTIONS...
  • Page 2: User Information

    User information Microsafe Mkomfy is a safety product from CTM Lyng AS. The product is mandatory for new installations and major renovation projects and is intended as extra safety for avoiding uncontrolled fire breakout and damage to property. The product assumes normal care in the use of the cooker and associated cooking implements.
  • Page 3: Temperature Sensor

    User information Sound alarm 1 sound signal: Timer function, time expired. 2 short sound signals: Battery needs changing. 3 short sound signals: Over-heating. Light Function button One press will extend the Temperature sensor time by 30 min, or turn Must be cleaned regularly with the cooker on after a cloth dampened with slightly disconnection.
  • Page 4: Battery Change

    User information Battery change Recommended every three years or when the battery warning signal is given. The sensor will warn about battery change when necessary. This is done by 2 short sound signals every 5 minutes. Flip the cooker guard away from the wall. Loosen two screws on the rear and remove the cover.
  • Page 5: Installation Information

    Installation information Installation information for sensor Carefully clean the wall and make sure it is dry before pressing the cooker guard into place at the correct height (remove the backing tape). The adhesive foot must be fixed to the cooker guard. NB: If a screw is used to fix the foot, the screw head may not be greater than 6.9 mm in diameter or protrude more than 2.5 mm.
  • Page 6: Function Test

    Installation information Function test To test for function, run a “forehead test” Slide switch Unscrew the rear cover of the sensor and set slide switch 4 to position ON. ① Sensor ① Point the sensor eye marked towards your own face/forehead and check that the cooker turns off (the temperature of your forehead is over 30°C).
  • Page 7 Installation information Sensor Rear Front DipSW Function button Dip 1 Not in use Dip 2 ON: *Extra-high temperature Dip 3 ON: **Induction Dip 4 ON: Function test and pairing mode. See pages 6 and 8. * Extra-high temperature (To be carried out only by an authorised installer) In certain locations or with certain types of hob, the sensor may be slightly over-sensitive.
  • Page 8 Installation information Pairing of Sensor and Cooker Guard Relay The Mkomfy set with sensor and cooker guard relay in the same pack are already paired. If you have bought a separate sensor, this must be paired with the cooker guard relay. This can be done in two different ways. Read through the whole instruction for both alternatives before performing pairing! Alternative 1: Pairing of Sensor without physical intervention on cooker guard relay.
  • Page 9 Installation information Overview of cooker guard relay Blue Yellow R-T 25A Green Programming button Explanation of LEDs Green Lights up continuously while the relay is connected. Flashes if there is no communication with the sensor * Flashes when paired units are deleted or if the command from the sensor is rejected.
  • Page 10 Installation information Installation is not complete until the radio connection has been checked by pressing the function button on the Sensor and noting that the red diode on the relay responds with a flash and that the Sensor acknowledges this with a sound signal and red flash. LOAD/CONTACTOR* R-T 25A *Can also control a contactor.
  • Page 11 User information Alarms signals with use of Mkomfy Alarm signal: One (1) sound signal every 15 seconds. Cause: In the last 5 minutes of the timer function. Action: Press the button for an extra 30 minutes of function time. Alarm signal: One (1) sound signal every second for 5 seconds.
  • Page 12 Timer: dimensions, sensor: 2 hours/12 hours 96x66x28 mm Battery type: Battery life: 2 pcs. AAA/LR03 Up to 6 years Transmitter power: 868,100 MHz +5 dBm El. No. Name 6251698 Mkomfy R-T 25A Manufacturer: CTM Lyng AS, www.ctmlyng.no, Tel. +47 72831611...

Table of Contents