Download
Share
Print this page
  1. Manuals
  2. Brands
  3. HMI Manuals
  4. Bathroom Fixtures
  5. TRU-FIT
  6. Installation instructions manual

HMI TRU-FIT Installation Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
PARTS LIST
ITEM PART
A ZSS-4506
B
ZSS-4505
C
ZSS 4504
D ZSS 4504
E
CHG HGTW*
F
CHG BTB
G CMF Anchor
H #10 x 2"
J
ZV-935
K #8 x 2"
L
#8 x 3/4"
M #10 x 3/4"
N ZV 969
O
P
Q SP-GSB125
R
CHGP982
S
CHGP976
T CHGP972
* Standard hinge part number listed. Reference original order PO for replacement parts.
Hinge styles may vary.
When ordering repair parts, please provide the following information:
1. Model Number
2. Part Number
3. Part Description
4. Finish Color
Required Tools:
• TWO PEOPLE
• Pencil
• Tape Measure
• Electric Drill
• Phillips Head Bit
• Scissors
• Level
• Flat Head Screwdriver
• Hammer
• Silicone
• Painters or Masking Tape
• 1/8" and either 3/16" or 1/4" Drill Bits*
* Select the proper drill bits for your installation conditions
(i.e. tile, porcelain, marble, etc)
V5_21_26
TRU-FIT
DOOR & PANEL
DESCRIPTION
Wall Jamb
Hinge Jamb
Longer Piece = Wall Channel
Shorter Piece = Curb Channel
Glass Hinge
Back-to-Back Pull
Plastic Anchors for Wall Jamb
Wall Jamb Screws
Plastic Anchors for Channels
Wall and Curb Channel Screws
Hinge Jamb to Wall Jamb Screws
Heavy Glass Hinge to Post Screws 8
Adjustable Post Cap
3/8" Clear Glass Door
3/8" Clear Glass Panel
Glass Blocks
Bottom Sweep
Angle Seal (Optional)
Bulb Seal (Optional)
INSTALLATION INSTRUCTIONS
QTY
1
1
1
1
2
1
6
8
6
6
5
1
1
1
6
1
1
1
IMPORTANT NOTE:
Door should not be used for 72
hours in order to let silicone
cure properly.
* The three pre-drilled holes and screws
go on the inside of the enclosure.
** The two screws on the outside of the
enclosure are optional, but
recommended for structural integrity.

Advertisement

loading
Need help?

Need help?

Do you have a question about the TRU-FIT and is the answer not in the manual?

Questions and answers

Summary of Contents for HMI TRU-FIT

  • Page 1 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL PARTS LIST IMPORTANT NOTE: ITEM PART DESCRIPTION A ZSS-4506 Door should not be used for 72 Wall Jamb ZSS-4505 Hinge Jamb hours in order to let silicone ZSS 4504 Longer Piece = Wall Channel cure properly.

  • Page 2: Door & Panel

    • These units have been tested under extreme usage condi- tions and have not failed WHEN PROPERLY INSTALLED. The TRU-FIT Shower Enclosure is made of tempered glass. While tempered glass is strong, it CAUTION on edge is hit too hard or something else happens it can break. Tempered glass is designed to shatter into small pieces, like automobile windows, but they can still be dangerous.
  • Page 3 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL STEP 1 Determine center line of your shower base by measuring the thickness of the Figure 1 base and use a pencil to mark the center. Draw this line the entire length of the base.
  • Page 4 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL STEP 5 Put a small amount of silicone in each hole drilled. Place Plastic Anchors (E), if needed, in holes and gently tap with a hammer. Be sure not to hit the tile. (see Figure 5)
  • Page 5 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL STEP 9 Put a small amount of silicone in each hole drilled. Place Plastic An- chors for Channels (J), if needed, in holes gently tap with hammer until anchor is flush. It might be necessary to use a razor knife to cut the lip of the anchor off so it is completely flush with the wall.
  • Page 6 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL STEP 13 Set Wood Block on center of base for spacing and safety. Set the Glass Door (O) on top of Wood Block (U) and position Hinge Jamb (B) to go over the Wall Jamb (A). USING TWO PEOPLE (1 PERSON INSIDE,1 PERSON OUTSIDE), slide Hinge Jamb (B) over Wall Jamb (A) carefully until fully compressed.
  • Page 7 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL STEP 16 Install three #8 x 3/4” Self Tapping Screws (L) into the pilot holes drilled. (See Figure 16) STEP 17 FIGURE 16 Now that the Glass Door (O) is secure, double check you have an 1/8”...
  • Page 8 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL STEP 20 With door in the open position, carefully remove the Glass Panel (P) and Glass Blocks (Q) and drill pilot holes in curb channel as shown in Figure 20 A. Replace the Curb Channel (D) under the Wall Channel (C). Use a pencil to mark for pilot holes and remove channel for drilling.
  • Page 9 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL STEP 23 Silicone the Glass Panel (P) in place by applying an even bead inside troughs on both sides of Wall Channel (C) and Curb Channel (D) as well as where the wall channel and curb channel meet the wall and base. (See Figure 23) Clean off any excess silicone.
  • Page 10 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL STEP 26 The Adjustable Post Cap (N) covers the exposed top of the Wall Jamb (A) and Hinge Jamb (B). Set the cap in place BACKWARDS (only to mark it for cutting) with the legs going in Hinge Jamb (B) (See Figure 26A) and mark for cutting (See Figure 26B).
  • Page 11 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL STEP 27 To attach the Back-to-Back C-Pull (F), first loosen set screws with an allen wrench and take the pull apart. (See Figure 27) NOTE: The pull is mounted so that there is no metal touching the glass. The clear plastic washers go on either side of the glass between the pull and the glass.
  • Page 12 TRU-FIT INSTALLATION INSTRUCTIONS DOOR & PANEL STEP 29 There are three different polycarbonates provided. All are OPTIONAL and serve to help prevent water from escaping shower. NOTE: If using the optional polycarbonates, for the best adhesion, clean glass or tile with alcohol before application.

  • Page 13: Troubleshooting

    • A complete description of the problem. • A photocopy of your invoice/receipts for the product installed. Under no circumstances should HMI Shower Enclosures products be returned to your dealer, distributor, or the HMI Shower Enclosures without a written Return Merchandise Authorization (RMA). V5_21_26...